S INSTRUCTION MANUAL FOR CALIBERS .357 Magnum, .30 Carbine, .41 Magnum, .44 Magnum, & .45LC BLUED & STAINLESS STEEL RUGER® NEW MODEL BLACKHAWK®, SUPER BLACKHAWK®, HUNTER & BISLEY SINGLE ACTION REVOLVERS READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL CAREFULLY BEFORE USING THIS FIREARM For Product Service on this Model Please Call: (603) 865-2442 (See p.
State-By-State Warnings Certain states require by law that their own specified warning notices in larger-than-normal type be conspicuously included by the manufacturer, distributor, or retail dealer with firearms sold in that state. Sturm, Ruger sells its products in compliance with applicable laws and regulations. Because our products may be sold in these states, we include the following: California: WARNING ADVERTENCIA “A los niños los atraen las armas de fuego y las pueden hacer funcionar.
Maine: “ENDANGERING THE WELFARE OF A CHILD IS A CRIME. IF YOU LEAVE A FIREARM AND AMMUNITION WITHIN EASY ACCESS OF A CHILD, YOU MAY BE SUBJECT TO FINE, IMPRISONMENT OR BOTH. KEEP FIREARMS AND AMMUNITION SEPARATE. KEEP FIREARMS AND AMMUNITION LOCKED UP. USE TRIGGER LOCKS.” Maryland: “WARNING: Children can operate firearms which may cause death or serious injury.
New Jersey: “IT IS A CRIMINAL OFFENSE TO LEAVE A LOADED FIREARM WITHIN EASY ACCESS OF A MINOR.” New York City: “THE USE OF A LOCKING DEVICE OR SAFETY LOCK IS ONLY ONE ASPECT OF RESPONSIBLE FIREARMS STORAGE. FOR INCREASED SAFETY, FIREARMS SHOULD BE STORED UNLOADED AND LOCKED IN A LOCATION THAT IS BOTH SEPARATE FROM THEIR AMMUNITION AND INACCESSIBLE TO CHILDREN AND OTHER UNAUTHORIZED PERSONS.
WHY ARE WE INCLUDING A FIRED CARTRIDGE CASE WITH EVERY RUGER PISTOL AND REVOLVER? Certain states and jurisdictions now require that all newly manufactured pistols and revolvers must be accompanied by a cartridge case, which has been test fired from that gun at the factory. The case must be placed in a sealed container bearing certain information concerning this test cartridge.
Use the Correct Lock: While the basic locking device is substantially similar for all Ruger firearms, due to the different shapes of the many Ruger firearms, some firearms utilize different locking devices. NEW MODEL BLACKHAWK® revolvers utilize a 2 1/2” lock. It is very important to use the correct locking device! To Install the Factory-Supplied External Locking Device: 1. Keep the muzzle pointed in a safe direction and your fingers outside the trigger guard at all times! 2.
OPERATION OF INTERNAL LOCK (ON REVOLVERS SO EQUIPPED) Never rely upon any safety mechanism or mechanical device to justify unsafe or careless handling of a firearm. When securing your revolver or to prevent unauthorized access, you should rely first and foremost on the key-operated locking device supplied with your revolver. (See Page 5.) However, for added security, and to comply with certain state and local laws, your NEW MODEL BLACKHAWK® revolver also is equipped with a manually operated internal lock.
Be sure to store the internal lock key in a secure location, away from children and careless adults. Do not store your firearm with the key in the internal lock keyway. Never lock a loaded gun – always unload the gun before locking. INSTRUCTIONS FOR ACCESSING INTERNAL LOCK THROUGH RIGHT GRIP PANEL If you would like to access the internal lock on your NEW MODEL BLACKHAWK® without removing the grips, you can drill a small hole through the right grip panel as follows: 1.
FIREARMS SAFETY-YOUR RESPONSIBILITY SAFETY MUST BE THE FIRST AND CONSTANT CONSIDERATION OF EVERY PERSON WHO HANDLES FIREARMS AND AMMUNITION. This Instruction Manual is designed to assist you in learning how to use and care for your RUGER® NEW MODEL BLACKHAWK® or BISLEY revolver properly. Please contact us if you have any questions about it. Only when you are certain you fully understand the Manual and can properly carry out its instructions should you practice loading, unloading, etc. with live ammunition.
WARNINGS OF GREAT IMPORTANCE ARE FOUND ON THE FOLLOWING PAGES: Locking Devices Alterations Lead Exposure Ammunition Handling Firing Safe Carrying Position 5 10 14 15 16 17 18 Disassembly Lubrication Storage Shipping Parts Purchasers Malfunctioning Parts 21 26 27 30 31 32 OTHER CAUTIONS AND WARNINGS APPEAR THROUGHOUT THE MANUAL. FIREARMS ARE DANGEROUS WEAPONS– READ THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL THOROUGHLY AND CAREFULLY BEFORE USING.
The patented Ruger New Model single action revolver mechanism incorporates a transfer bar. The transfer bar – which is raised into firing position as the trigger is pulled to the rear – transmits the energy of the hammer blow to the firing pin. This transfer bar mechanism makes a “safety” notch unnecessary. The gate (loading gate) can be opened only when the hammer and trigger are fully forward. Opening the gate immobilizes the trigger, hammer, and transfer bar.
NOMENCLATURE Bisley Fluted Cylinder Model Shown CAUTION–NUMBERED CYLINDERS 3 4 5 4 5 3 00-00345 Do not accept delivery of a New Model Blackhawk Convertible (a model with two cylinders) unless the numbers on the front face of both cylinders match the last three digits of the serial number on the frame. Use of the wrong cylinder can cause improper alignment or timing and may result in personal injury.
The mechanism of the RUGER® NEW MODEL BLACKHAWK® & BISLEY provides maximum security against accidental discharge. As with any other firearm, however, the New Model must be used with strict attention to correct safety practices. In addition, the revolver should be inspected frequently to assure that it is working properly. The Ruger New Model revolver mechanism is illustrated below.
WARNING - LEAD EXPOSURE Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead and other substances known to the state of California to cause birth defects, reproductive harm, and other serious physical injury. Have adequate ventilation at all times. Wash hands thoroughly after exposure. SHOOTING OR CLEANING GUNS MAY EXPOSE YOU TO LEAD AMMUNITION The table below shows the correct type of ammunition for use in each of the revolvers listed.
AMMUNITION (CARTRIDGES) NOTICE WE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR ANY DAMAGE OR INJURY WHATSOEVER OCCURRING IN CONNECTION WITH, OR AS THE RESULT OF, THE USE IN RUGER REVOLVERS OF FAULTY, OR NONSTANDARD, OR “REMANUFACTURED” OR HANDLOADED (RELOADED) AMMUNITION, OR OF CARTRIDGES OTHER THAN THOSE FOR WHICH THE FIREARM WAS ORIGINALLY CHAMBERED.
Notes on the .44-40/44 Mag. Super Blackhawk Convertible (this model no longer in production): Ruger New Model Super Blackhawk convertible revolvers using the cylinder chambered for the .44-40 cartridge can use all factory loadings of this ammunition both regular and high speed. Do not use any other ammunition in the .44-40 cylinder. The .44 magnum cylinder can use all factory loadings of the .44 magnum cartridges and .44 special cartridges. Notes on Revolvers Chambered for 9mm or .
TO LOAD AND FIRE 1. Do not load the revolver until you are ready to use it. 2. Note – The loading gate cannot be opened unless the hammer and trigger are fully forward, and the hammer cannot be cocked once the gate is opened. 3. Open the gate. This permits the cylinder to rotate. 4. Turn cylinder clockwise, by hand, and insert cartridges in chambers. 5. Align a chamber with the barrel and close the gate.
CAUTION: The recoil of any centerfire caliber causes the muzzle of the gun to flip upward with substantial force. The shooter need not be apprehensive, but be prepared. Keep a firm grip on the revolver and hold it away from your face when firing. DRY-FIRING: Going through the actions of cocking, aiming, and pulling the trigger of an unloaded gun is known as “Dry Firing.” It can be useful to learn the “feel” of your revolver.
TO ‘UNCOCK’ (DECOCK) THE REVOLVER If your revolver is cocked, and you wish to let the hammer down to its forward position (against the frame), proceed as follows: USE EXTREME CARE WHEN ATTEMPTING TO DECOCK THE REVOLVER, AS THE THUMB SLIPPING DURING THIS PROCESS CAN RESULT IN AN ACCIDENTAL DISCHARGE IF THE TRIGGER IS HELD TO THE REAR. 1. Make certain that the revolver is pointing in a safe direction (See Rule 2, Page 42). 2.
The revolver is now in its normal carrying condition -- hammer and trigger fully forward and transfer bar lowered out of firing position. CAUTION: The hammer must be carefully eased fully forward before the hammer is drawn back to the full-cock position for the first shot. The hammer should be drawn with a firm positive motion to the fullcock position for each shot, thus actuating the working parts for complete indexing.
CORRECT UNLOADING SEQUENCE 2 3 1 REPEAT FOR ALL CHAMBERS 4 Do not eject unfired cartridges onto any surface where the cartridge primer might strike a solid object and discharge the cartridge. WARNING – DISASSEMBLY 2 Never clean, lubricate, disassemble or work on a revolver while it is loaded. Never install or remove a loaded cylinder. A loaded cylinder can discharge if dropped or struck. Read instructions before disassembling gun.
The tip of the screwdriver blade should perfectly fit the grip frame screw slots. A tip too large will scrape away metal, while too small a tip will damage the screw slots. Before taking the gun apart, set up to do it properly. Cover the work surface with a soft cloth so that the gun finish (and sights) will not be damaged, and provide a tray into which the parts can be put as they are removed from the gun. DISASSEMBLY (Make Sure Revolver is Unloaded!) 1.
7. Remove cylinder latch, gate detent spring, and gate. 8. Remove hammer pivot. Then remove the hammer/pawl assembly and the trigger/transfer bar assembly. (Note that the hammer is attached to the pawl and the transfer bar is attached to the trigger. See Figure 5). (Groove in Hammer Pivot) (Groove in Trigger Pivot) Figure 4 Figure 5 ALTHOUGH THE FOREGOING OUTLINES THE CORRECT PROCEDURE, WE WISH TO EMPHASIZE THAT SUCH DETAILED DISMANTLING IS SELDOM IF EVER NECESSARY.
2. (Refer to Figure 4, p. 23). Align hammer in frame and insert hammer pivot with the grooved end of the pivot on the gate side of the frame. (The long screw, XR01901, when also inserted on the gate side, will intersect the groove and lock the pivot in place. See step number 11, p. 25). 3. Replace the loading gate, cylinder latch and gate detent spring as shown in Figure 6.
11. See Figure 7, and note the end of the trigger spring (the arrow marked “A”). This end of the spring must be depressed so that it slides under the rear portion of the trigger when the grip frame is forward. With all the above springs and plungers aligned, fully mate the grip frame and cylinder frame and install the five grip frame screws. Note that the long screw (XR01901) should go in the grip frame hole on the gate side (Figure 7-B) of the revolver. 12.
Some cartridges with lead bullets deposit metal fouling in the chamber throats, in the forcing cone of the barrel, and in the bore. If ‘leading’ is noted in your revolver, clean it out before it builds up and interferes with reliable functioning and accuracy. A special ‘lead removing’ cleaning tool (for bore and chambers) is available from gun stores. The revolver’s internal mechanism can be lubricated without disassembly.
STORAGE GUNS SHOULD NOT BE STORED LOADED! USE THE LOCKING DEVICE SUPPLIED WITH THE REVOLVER TO RENDER IT INOPERATIVE FOR SAFE STORAGE. (SEE PAGE 5) Do not keep your revolver in a leather, fabric or canvas holster when it is stored. These materials attract moisture, even though the holster may appear to be perfectly dry. Sturm, Ruger also offers gun safes for sale as a means to secure more than one firearm. Please call the Heritage Safe Company at 1-800-515-7233 for details and ordering information.
CARE OF STAINLESS STEEL REVOLVERS Firearms made of stainless steel are relatively more resistant to corrosion than blued steel firearms. However, you should still inspect it frequently and clean, lubricate and apply an appropriate rust preventative as required. Sometimes surface discoloration may be noted, particularly in the grip area of stainless steel handguns, resulting from perspiration. Contact with some types of holsters can also cause stains or rusting.
SIGHTS (ON REVOLVERS SO EQUIPPED) ADJUSTMENT – Each click of the sight adjustment screw (either windage or elevation) will move the point of impact of the bullet approximately 3/4” at a range of 25 yards. The height of the front sight has been set to take advantage of the elevation adjustment in the rear sight, considering the various ranges at which the gun is most likely to be used. Barrel length and load used affects trajectory. Therefore the shooter should determine sight settings by firing trials.
SERVICE AND PARTS POLICY If you have any questions with regard to the performance of your RUGER® NEW MODEL BLACKHAWK or BISLEY revolvers, please write or call (603-865-2442) our Newport, New Hampshire Product Service Department, fully describing all circumstances.
It is the purchaser’s responsibility to be absolutely certain that any parts ordered from the factory are correctly fitted and installed. Firearms are complicated mechanisms and IMPROPER FITTING OF PARTS MAY RESULT IN A DANGEROUS MALFUNCTION, DAMAGE TO THE FIREARM, AND SERIOUS INJURY TO THE SHOOTER AND OTHER PERSONS. The purchaser and installer of parts must accept full responsibility for the correct adjustment and functioning of the revolver after such installation.
WHEN ORDERING PARTS BE SURE TO STATE WHETHER YOUR REVOLVER IS BLUED OR STAINLESS. ALSO, INCLUDE THE COMPLETE SERIAL NUMBER AND SPECIFY THE CALIBER AND BARREL LENGTH. GRIP FRAME NOTE: The New Model Super Blackhawk steel Grip Frame (Stainless steel or blued) will fit any New Model Single Six or New Model Blackhawk revolver. However, because the Grip Frame must be “match-polished” to fit each cylinder frame, it is furnished (as a component part) only ‘in the white,’ that is, not polished or blued.
RUGER® NEW MODEL BLACKHAWK®, SUPER BLACKHAWK®, HUNTER & BISLEY PARTS LIST Design, prices and specifications subject to change without notice.
Part Name * Barrel, 7 1/2” - .45 LC Base Pin Assembly Base Pin Assembly Base Pin Latch Body Base Pin Latch Body (high gloss finish) Base Pin Latch Nut Base Pin Latch Nut (high gloss finish) Base Pin Latch Spring Base Pin Latch Spring Case - 4 5/8” & 5 1/2” barrels Case - 6 1/2” & 7 1/2” barrels Case - 10 1/2” barrels * Cylinder - .30 cal. * Cylinder - .357 cal. * Cylinder - .357 cal. * Cylinder - .357 cal., non-fluted cyl. * Cylinder - 9mm * Cylinder - .41 cal. * Cylinder - .44 mag. cal. * Cylinder - .
Part Name Cylinder Latch Assembly Cylinder Latch Spring Cylinder Latch Spring Cylinder Latch Spring Plunger Cylinder Latch Spring Plunger Ejector Housing - Aluminum Ejector Housing - Satin Finish Ejector Housing - Steel Ejector Housing - Steel Ejector Housing - Satin Finish Ejector Housing Ejector Housing Screw Ejector Housing Screw (high gloss finish) Ejector Housing Spring Ejector Housing Spring Ejector Housing Spring Ejector Housing Spring Ejector Rod Assembly Ejector Rod Assembly Ejector Rod Assembl
Part Name Front Sight, Red Insert Front Sight Base - .357 cal., .45LC, & .44 mag. (except 10 1/2” bbl.) Front Sight Base - .44 mag. Front Sight Base - .45LC & .45/45ACP Front Sight Blade - .357 cal., .45LC, .45/45ACP & .44 mag. Front Sight Blade - .45LC (7 1/2” bbl.) Front Sight Locating Pin Part No. H03600 KMR13601 Model Hunter Blackhawk & Super Blackhawk - Stainless Models MR-36-44 MR-36-45 MR03600 Super Blackhawk, 10 1/2” bbl.
Part Name Grip Frame Screw - B - Back (2 Req’d.) Grip Frame Screw - B - Back (hex screws - 2 Req’d.
Part Name Hammer Strut Mainspring Mainspring Mainspring Seat Mainspring Seat Medallion, 2 Req’d.
Part Name Recoil Plate Cross Pin Recoil Plate Cross Pin Scope Base Torx® Head Screw, 8 Req’d Scope Ring Assembly, Medium Rings Scope Ring Clamp Scope Ring Nut Scope Ring Screw Torx® Key Wrench, Not Illustrated (for Scope Base Torx® Head Screw) Transfer Bar Trigger, High Gloss Finish Trigger, High Gloss Finish Trigger Trigger Pivot Pin Trigger Pivot Pin Trigger Spring Trigger Spring Trigger Spring Pivot Pin Trigger Spring Retaining Pin Part No.
NEW MODEL BLACKHAWK® & SUPER BLACKHAWK® EXPLODED VIEW BLACKHAWK® SUPER BLACKHAWK® 40
RUGER® BISLEY EXPLODED VIEW HUNTER MODEL COMPONENT PARTS 41
THE BASIC RULES OF SAFE FIREARMS HANDLING We believe that Americans have a right to purchase and use firearms for lawful purposes. The private ownership of firearms in America is traditional, but that ownership imposes the responsibility on the gun owner to use his firearms in a way which will ensure his own safety and that of others. When firearms are used in a safe and responsible manner, they are a great source of pleasure and satisfaction, and represent a fundamental part of our personal liberty.
A safe direction must take into account the fact that a bullet may penetrate a wall, ceiling, floor, window, etc., and strike a person or damage property. Make it a habit to know exactly where the muzzle of your gun is pointing whenever you handle it, and be sure that you are always in control of the direction in which the muzzle is pointing, even if you fall or stumble. Keep your finger off the trigger until you are ready to shoot! 3. FIREARMS SHOULD BE UNLOADED WHEN NOT IN USE.
5. BE SURE OF YOUR TARGET BEFORE YOU SHOOT. Don’t shoot unless you know exactly where your bullet is going to strike. Be sure of the bullet stop behind your target, even when dry-firing with an unloaded gun. If you are in the field hunting, do not fire at a movement or noise. Take the time to be absolutely certain of your target before you pull the trigger. 6. WEAR SHOOTING GLASSES AND HEARING PROTECTORS WHEN YOU SHOOT.
8. DON’T SHOOT AT A HARD SURFACE, OR AT WATER. Bullets can glance off many surfaces like rocks or the surface of water and travel in unpredictable directions with considerable velocity. 9. NEVER TRANSPORT A LOADED FIREARM. Firearms should always be unloaded before being placed in a vehicle. A suitable carrying case or scabbard should by used to carry an unloaded firearm to and from the shooting area. 10. AVOID ALCOHOLIC BEVERAGES WHEN SHOOTING. Don’t drink until the day’s shooting is over.
A BRIEF ACCOUNT OF AN EXTRAORDINARY ACHIEVEMENT: RUGER FIREARMS Sturm, Ruger & Company, Inc., had its beginning in a small machine shop occupying a rented frame building in Southport, Connecticut. In January, 1949, with an initial investment of only $50,000 and an idea, William B. Ruger and Alexander M. Sturm started production of a .
WHY NO WARRANTY CARD HAS BEEN PACKED WITH THIS NEW RUGER FIREARM The Magnuson-Moss Act (Public Law 93-637) does not require any seller or manufacturer of a consumer product to give a written warranty. It does provide that if a written warranty is given, it must be designated as “limited” or as “full” and sets minimum standards for a “full” warranty. Sturm, Ruger & Company, Inc.
