User's Manual

ManualsBrandsRTX Hong Kong ManualsElectronicsUPCS Repeater

Contents

1) Getting to know your repeater......................2

Checking the package contents.............................2

How it works.........................................................2

Features............................................................3

Specifications...................................................4

2) Setting up your repeater................................4

Setting up the base................................................5

Changing the telephone system PIN................5

Automatic registration..........................................5

Manual registrationError! Bookmark not defined.

Registration for a daisy-chain layout ...................6

Registering to a different base..............................6

3) Installing the repeater....................................6

Finding the right location.....................................6

Map the base's coverage area...........................7

Test the location...............................................7

Installing the repeater...........................................8

Multiple-repeater systems.....................................8

Incorrect installation ........................................9

Correct installation...........................................9

Daisy-chain installations................................10

4) Troubleshooting and Maintenance.............11

Turning on the verification tone .........................11

Maintenance .......................................................12

5) Legal and warranty information................12

Important safety instructions ..............................12

Important electrical considerations................13

FCC regulatory information...............................13

Part 15 compliance.........................................13

Privacy information .......................................14

Radio interference information......................14

I.C. Notice...........................................................15

Terminal Equipment ......................................15

Radio Equipment ...........................................15

One Year Limited Warranty................................15

Contact Information............................................17

Having Trouble? ............................................17

Need a Part?...................................................17

Help for our Special Needs Customers..........17

Summary of content (17 pages)

PAGE 1
Contents 1) Getting to know your repeater...................... 2 Checking the package contents............................. 2 How it works......................................................... 2 Features............................................................ 3 Specifications................................................... 4 2) Setting up your repeater................................ 4 Setting up the base ................................................ 5 Changing the telephone system PIN ....
PAGE 2
1) Getting to know your repeater Checking the package contents You should have received the following items: • UDR100 DECT repeater • AC adapter • Mounting screw and wall anchor How it works The UDR100 repeater lets you extend the coverage area of your cordless DECT telephone system in all directions, including up and down.
PAGE 3
In addition, the UDR100 supports a sequential or "daisy chain" layout to extend coverage in a single direction. Up to 3 repeaters can be installed in sequence: For detailed information on daisy-chain layout and configuration, contact your installer or refer to the UDR100 Administrator's Guide.
PAGE 4
• Up to 6 repeaters per base station • Up to 3 repeaters in a sequential or daisy-chain layout • 2 internal antennas to support 2 simultaneous calls • Repeater connection verification tone • Low power consumption Specifications Unit weight: Input: 100 -240VAC 50 -60Hz Output; 5VDC 500mA 5oz (142g) Frequency band: 1920Mhz -1939Mhz Transmit power: 110mW Receiver sensitivity: <-92 dBm at 10-3 BER Operating Temperature 14° to 122° F (-10° to +50° C) Standards: Designed in accordance with the Digita
PAGE 5
Use ONLY the power adapter that came with your repeater. A different power adapter may cause an electrical hazard or damage the repeater. Setting up the base Changing the telephone system PIN Before you start the registration process, you must reset the system PIN of your telephone to 0000 (consult the manual that came with your base for more information). After you reset the PIN, make sure to re-register the handset you used back to the base station.
PAGE 6
Registration for a daisy-chain layout Registering the repeaters to operate in a daisy-chain or sequential layout requires network administrator access and configuration software. Contact your installer or refer to the UDR100 Administrator's Guide (provided with the configuration software) for more information. Registering to a different base Once the repeater is registered, you need to reset it before you can change the registration to a different base.
PAGE 7
walls, niches and cupboards. Map the base's coverage area To find the best location for the repeater, you need to determine the base's coverage area. Stand near the base and make a call. Walk away from the base with the handset, and make a note where the signal becomes weaker. The optimum location for the repeater is as far from the base as possible while still maintaining a "good" signal, or just inside the location where the signal became weaker.
PAGE 8
repeater to another location. Installing the repeater Be sure the wall material can hold the weight of the repeater. Never install a repeater in damaged or decaying wall material. Step 1: Hold the repeater in its final location, and mark the center of the top edge. Step 2: From the edge mark, measure down approximately 1 1/2 inches, and mark the screw location. Step 3: At the screw location, use a 3/16ths drill bit to make a pilot hole approximately 1 inch deep.
PAGE 9
Incorrect installation Correct installation
PAGE 10
Daisy-chain installations You can combine "normal" and "daisy-chain" connections to create a wide variety of coverage configurations, as long as you have no more than six repeaters per base unit: For detailed information on daisy-chain layout and configuration, contact your installer or refer to the UDR100 Administrator's Guide.
PAGE 11
4) Troubleshooting and Maintenance Problem There is a lot of static when calls handoff to the repeater. AND/OR The LED on the repeater won't stop flashing. Try... • Moving the repeater closer to the base. • Checking for interference from electronic devices. • Making sure the repeater is not too close to metal objects or thick walls. • Making sure the repeater is inside the base's good signal range. Calls won't handoff to the repeater. • Making sure there is at least 35 feet between repeaters.
PAGE 12
Maintenance Caution: Unplug the repeater from the wall outlet before cleaning! • Wipe the front of the repeater front with a damp cloth or an antistatic wipe. • Do not apply liquid cleaners directly on the repeater. • Never use aerosol cleaners or solvents. • To avoid static discharge, never use a plain dry cloth.
PAGE 13
• To reduce the risk of electric shock, do not disassemble this product. Contact qualified service personnel when some service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: • When the power supply cord is damaged or frayed.
PAGE 14
Privacy information Cordless telephones are radio devices. Communications between the handset and base of the cordless telephone are accomplished by means of radio waves which are broadcast over the open airways. Because of the inherent physical properties of radio waves, communication can be received by radio receiving devices other than your own telephone unit, consequently, any communications using the cordless telephone may not be private.
PAGE 15
I.C. Notice Terminal Equipment NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
PAGE 16
E. used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or F. installed or programmed by anyone other than as detailed by the owner’s manual for this product.
PAGE 17
Uniden America Service 4700 Amon Carter Blvd. Fort Worth, TX 76155 Contact Information Having Trouble? Our customer care specialists are here to help you! Visit our website at www.uniden.com or call our Customer Hotline at 1-800-297-1023 during regular business hours.* Need a Part? To order headsets, additional handsets, replacement batteries or other accessories, visit our website at www.uniden.com or call 1-800-554-3988 during regular business hours.