RPT-110-3PCxxx-K9 REPEATER USER GUIDE Technical Reference Document Version 1.
Trademarks RTX and the combinations of its logo thereof are trademarks of RTX A/S, Denmark. Other product names used in this publication are for identification purposes and maybe the trademarks of their respective companies. Regulatory information United States Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules.
Confidentiality This document should be regarded as confidential, unauthorized copying is not allowed © May-2019 RTX A/S, Denmark, All rights reserved http://www.rtx.
Contents 1. 2. Introduction ................................................................................................................................................................ 5 1.1. Document History ............................................................................................................................................. 5 1.2. What is new......................................................................................................................................
1. Introduction The RPT-110-3PCxxx-K9 repeater user guide is designed to give a detailed overview on how to install, register and manage RTX repeaters 1.1. Document History REVISION 1.0 1.1 1.2 AUTHOR HDJ JSK JSK ISSUE DATE 26-06-2019 15-08-2019 20-09-2019 1.2. What is new What new features have been added. VERSION V460 FEATURE 1.3.
2. Installation of Repeater After planning the network, next is to determine the proper places or location the repeater. The repeater should be mounted as high as possible. 2.1. Package – Contents/Damage Inspection Before Package Is Opened: Examine the shipping package for evidence of physical damage or mishandling prior to opening. If there is a proof of mishandling prior to opening, you must report it to the relevant support center of the regional representative or operator.
2.2. Damage Inspection The following are the recommended procedure for you to use for inspection: 1. Examine all relevant components for damage. 2. Make a “defective on arrival – DOA” report or RMA to the operator. Do not move the shipping carton until the operator has examined it. If possible, send pictures of the damage. The operator/regional representative will initiate the necessary procedure to process this RMA.
2.3. Repeaters Mechanics The repeaters front end shows an LED indicator that signals different functional states of the repeater. The indicator is off when the repeater is not powered on.
2.4. Mounting the repeater There are 2 way to mount the repeater.
3.
4. Repeater registration There are 2 different ways to register RTX repeater’s “Local Automatic” and “Manually” Local Automatic: In this mode the repeater registers to the base station with best signal strength, this option is only recommended for single cell systems and Multi cell systems where the repeater is only able to sync with one specific base station. Manually: Manual registration is used in most cases when adding repeaters to a multi cell system.
Screen shot Step 3: Give the repeater a name and press “save” Step 4: Power on the repeater(s) and registration will start. When the LED is steady green the repeater is successfully registered. Screen shot PARAMETERS DESCRIPTION IDX System counter RPN SINGLE CELL SYSTEM: The base has always RPN00, first repeater will then be RPN01, second repeater RPN02 and third RPN03 (3 repeaters maximum per base) MULTI CELL SYSTEM: Bases are increment by 2^2 in hex, means first base RPN00 second base RPN04 etc.
4.2. Register repeater(s) “Manually” NOTE: Do not power on the repeaters before they have been added on the base station NOTE: When adding first repeater the base station(s) will reboot, this is because encryption is being enabled, the same goes if all repeaters is deleted, then the system will reboot to disable encryption. Step 1: To register repeater(s), navigate to the Repeater page.
Screen shot Step 5: Select the RPN for the repeater. ERROR: The repeater will choose the first available slot on the selected base station. RPN x: The repeater connects to RPN x of the chosen base station. E.g.
5. Firmware update The repeaters are updated over air.
PARAMETER DEFAULT VALUE(S) DESCRIPTION FIRMWARE UPDATE SERVER ADDRESS Empty IP address or DNS of firmware update files source Valid Inputs: AAA.BBB.CCC.DDD or Example: firmware.rtx.net or 10.10.104.41 FIRMWARE PATH Empty Location of firmware on server (or firmware update server path where firmware update files are located). Example: RTXFWU TERMINAL FILE PATH Empty Location of image (folder where background and start up image are located).
6. LED and button Power cycle The repeater basically has two modes: Subscribed or not subscribed. When powered up without a registration, the following applies.
RED n flash n handset relayed by repeater RED Steady on 1. Registration procedure timed out after 5 min. 2: When key is held pressed the LED will light up in 2 sec. to indicate that releasing the key will delete registration, LED turns off after 4 more sec. RED/GREEN Flashing Red/Green Recovery mode – repeater is locked to base station/repeater without repeater mode activated. 1: Sync. Source base station/Repeater not found (Manual mode).
