Handset Operations Manual RTX 8830 Version 1.
Contents Handset Operations Manual ....................................................................................................................... 1 Contents...................................................................................................................................................... 2 1 About This Document ......................................................................................................................... 5 1.1 Audience ..................................
5 Basic Operation................................................................................................................................. 17 5.1 How to Switch the Handset On/Off ............................................................................................... 17 5.2 Lock/Unlock the Keypad ................................................................................................................ 17 5.3 Entering a number in idle ....................................................
6.8 F-Keys ............................................................................................................................................. 61 6.9 Alarm List ....................................................................................................................................... 62 7 6.9.1 How to Trigger Alarms on the Handset .................................................................................. 62 6.9.
1 About This Document This document describes the features and functionalities available in the RTX SME VoIP DECT 8830 Handset. We describe how to operate the handset without going into details of its mechanical features. 1.1 Audience This guide is intended for everyday users as well as system administrators. 1.
2 Making Handset Ready In this chapter we briefly describe how to prepare the handset for use, install, and how to insert and charge new batteries. 2.1 Package - Contents/Damage Inspection 2.1.1 Before Package Is Opened Examine the shipping package for evidence of physical damage or mishandling prior to opening. If there is proof of mishandling prior to opening, you must report it to the relevant support center of the regional representative or operator. 2.1.
2.1.3 Damage Inspection The following are the recommended procedure for you to use for damage inspection: 1. Examine all relevant components for damage. 2. Make a “defective on arrival - DOA” report or RMA to the operator. Do not move the shipping carton until it has been examined by the operator. The operator/regional representative will initiate the necessary procedure to process this RMA. They will guide the network administrator on how to return the damaged package if necessary. 3.
2.2.4 How to Open Back Cover 1. Twist the back-cover lock to open position and lift back cover away from the handset. 2. Remove Back Cover from Handset 2.2.5 How to Replace Battery Remove the back cover from the handset as showed in section 2.2.4 How to Open Back Cover above. Then remove the old battery and replace with a new one. 2.2.
3 Phone Overview This section contains an overview of the handset from a front and a rear view. 3.1 Handset Front View and Top View 1. Earpiece Speaker 2. Screen 3. Navigation Keys (Up/Down/Right/left) 4. Selection Key (Centre of Navigation Keys) 5. Call Key/ Accept Call Key (Off-hook key) To answer a call, and functions as a short cut to the Call list. 6. End, ON/OFF Key, Back Key (On-hook key) To end call, to return to a previous menu, and to switch the handset on/off by long press. 7.
3.2 Handset – Rear View 12. Headset connector (3.5mm) This is for connecting a headset. The connector is protected against dust by the headset connector cover. 13. Belt Clip 14. Pull Cord For using a magnetic pull cord to activate the pull cord alarm. 15. Volume Up/Down Key (Side Key) To increase/decrease the volume during call. 16. Mute Key (Side Key) To turn off the microphone in call, so that the counterpart is muted. 17.
4 Display This section contains a description of the different icons seen in the idle and in the menu. 4.1 Icons and Text in the Display All functions and settings available to the handset user are shown as icons and text in the display. The icons and text in the display indicate functions and settings to which you have access.
“Voice mail message” icon is displayed in the status bar when there are voice mails that have not been listened to. This icon remains until the voice mail has been listened to. “Message” icon is displayed in the status bar when there are messages on the handset that have not been read. “Bluetooth Enabled” icon is displayed when Bluetooth is enabled on the handset, but the handset is not paired with any Bluetooth device.
During navigation across the different menus the highlighted icon is moving to indicate where the navigation key is. The menu icons are showed and shortly explained in the following: The “Contacts” menu contains all names/numbers in the local phonebook. The “Central directory” menu contains all names/numbers in the central directory of the system.
4.3.3 Speaker Key The speaker key is used to shift between speaker mode and normal mode during call. When the handset is set to speaker mode during call the speaker key lights up in red, and the sound comes from the speaker on the back of the handset. 4.3.4 Activity Menu Key When using this key from idle the activity menu is opened from which all the different menus available on the handset can be opened. 4.3.
When the mute function is enabled during a call it is indicated on the “Connected” screen with the image of the handset that is red as seen above. Mute is turned off by pressing the mute button again. 4.4 The Keypad The keypad is used when entering a name or number, and the sketch below shows the available characters on the handset. NOTE: Depending on the selected menu language, other characters can be available. Therefore the character order can differ from the table above. 4.4.
4.4.3 Silent Mode from #-Key By long-pressing the #-key when the handset is in idle, the handset will turn to silent mode, and a “Sound Off” icon will be shown in the status bar. This feature enables that the user rapidly can turn on silent mode. To turn off silent mode again long press the #-key in idle, or enter “Audio settings” and disable the “Silent” profile. NOTE: When this mode is enabled it is possible to switch on the vibrator on the handset in Audio Settings > Vibrator (see 7.6.
5 Basic Operation The following explain three basic operations of the handset: How to switch the handset on/off, how to lock/unlock the keypad, and the available options when entering a number in idle. 5.1 How to Switch the Handset On/Off Switching on the handset To switch the handset on long press the on-hook key to switch the handset on.
6 Menu Operation In the following a description of the different menus and submenus on the handset will be given. Before the functions of every menu are explained a menu tree will be showed at top to give an overview of how to enter the different menus. From idle it is possible to enter some of the menus directly via the three softkeys as displayed on the image below.
6.1.1 Add Contact To add a new contact press the right softkey “More”, select “Add contact”, and the information displayed in the menu tree below can be filled out for the contact. Hereby, it is possible to edit the name, add different phone numbers (work, mobile, home, and other), and add a specific ringtone to be used for exactly this contact. To save a new contact, press the left softkey “Safe”. 6.1.
Pressing “Call” initiates a call to this contact. When pressing “Edit” it is possible to edit the name, work, mobile, home, other, or ringtone for the highlighted contact. 6.1.3 More Contacts Options When a specific contact is highlighted, pressing “More” in the “Contacts” menu enables the features seen below. Edit before call This function makes it possible to edit the number of the contact before calling the contact.
A contact can only be assigned to one speed dial number at a time. The first defined number of the contact will be dialed when the speed dial key is pressed. This means that if all numbers (work, mobile, home, and other) are defined for the contact then the work number will be dialed. If the work number is not defined then the mobile number is dialed etc. NOTE: The ‘1’ key is reserved for voicemail. Long key press on ‘0’ is used for starting a normal dial string with ‘+’. 6.1.4.
NOTE: The speed dial function can also be set up for the F-Keys (for additional information on this see section 7.8 F-Keys) 6.2 Central Directory In the “Central directory” menu different contacts can be called according to which list the system administrator has setup in the base system. This menu can be entered directly from idle with the middle softkey , or from the menu by pressing the menu activity key “Central directory”. and choosing 6.2.
NOTE: When the central directory is in LDAP mode pressing right softkey “Back” the handset will return to the “Search” field, and a new search for a contact can be made. Pressing the red “On-hook” button, in the central directory, will send the user back to idle. If the central directory instead of LDAP Mode is set to Local mode, opening the central directory will get you directly to browsing mode, and to enter the search mode press the middle softkey as displayed below.
To scroll through the search results use the navigation keys up and down and you will scroll through the list. If a green arrow is seen to the right of a contact (as seen above), this contact has more than one number added, and to scroll through these different numbers use the left/right navigation keys. 6.2.2 Calling a Contact in the Central Directory To call a contact from the central directory press the green “Off-hook” button, and the contact number that currently appears on the screen will be called.
This menu can be entered directly from idle with the right softkey button , by pressing the green off-hook or from the menu by pressing the menu activity key and choosing “Calls”. When opening the “Calls” menu, the list “All calls” is automatically opened. Using the left/right navigation keys it is possible to view the four different lists. All calls: This list consists of all the different call types (including both outgoing and incoming) that have been made on the handset.
Using the up/down navigation keys scrolls through the list of missed calls. When the entries has been displayed once, the text displaying call information is no longer bold, and the red missed call icon disappears from the status bar indicating that the user has seen missed call; this is displayed in the second image above. 6.3.1 Call To initiate a call directly from the local call list use the up and down navigation keys to highlight an entry, and press the left softkey “Call”.
6.3.3 More Calls Options When a specific call is highlighted, pressing “More” in the “Calls” menu enables the features seen below. View details This shows the same details about the call as the “View” function explained in 7.3.1 Call/View. Save as contact With this feature it is possible to save the number in the call list as a contact. Append to contact This function makes it possible to add the number in the call list to an existing contact.
To delete all items in the specific list, press the left softkey “Yes”. To return to the call list, press the right softkey “No”. 6.4 Connectivity The “Connectivity” menu is entered in the menu by pressing the menu activity key in idle. In this menu it is possible to register or deregister the handset to a certain base system. Moreover, the “Select network” function makes it possible to register the handset to more than one base system. 6.4.
NOTE: For the handset to function on different base systems, the handset must be completely out of range of system 1 to connect to system 2. 6.4.2 Deregister The handset can be deregistered from a registration. The user will in this case be prompted for a PIN code (base deregistration PIN), the PIN code is default “0000” and cannot be changed via the handset. This is displayed below.
6.5 Settings The “Settings” menu is entered through the menu by pressing the activity menu key in idle. The “Settings” menu contains the following personal handset settings: Settings Audio settings Time & Date Language LED Signal Power save Security Handset name Line Reset settings Status Auto answer Silent charging Do not disturb Hide number Call Forward Idle screen saver Bluetooth Each of these settings will be described in the following. 6.5.
6.5.1.1 Silent The “Silent” profile can be either enabled with the right softkey “On”, or disabled with the left softkey “Off”. When the “Silent” profile is enabled no sounds are played on the handset, and the handset does not ring on incoming calls or messages. In the Audio settings menu only “Ring emergency”, “Vibrator” and “Noise reduction” can be entered when the “Silent” profile is enabled.
To select the desired ring volume the navigation keys up/down or right/left is used to respectively increase or decrease the volume. Thereby, pressing “Ok” saves the current ring volume. The currently applied ring melody is played when adjusting the ring volume so that the respective ring volume can be heard before selected. Ring mute The ringer is switched off when the lowest level is selected in “Ring volume”, and a mute image is showed in the display as seen below.
To hear the melody before selecting it, each melody in the list can be played by selecting the right softkey “Play”. The softkey “Play” changes to “Stop” during playback and the playback can then be stopped by pressing this button. 6.5.1.3 Ring normal and urgent message The handset can receive messages with both a normal priority and an urgent priority. Therefore different ring melodies can be selected for each type of received message. Ring normal msg. In the “Ring normal msg.
To select the desired alert volume the navigation keys up/down or right/left is used to respectively increase or decrease the volume. Thereby, pressing “Ok” saves the current alert volume. The currently applied alert melody is played when adjusting the alert volume so that the respective alert volume can be heard before selected. Alert mute The alert sound is switched off when the lowest level is selected in “Alert volume”, and a mute image is showed in the display.
To hear the melody before selecting it, each melody on the list can be played by selecting the right softkey “Play”. The softkey “Play” changes to “Stop” during playback and the playback can then be stopped by pressing this button. 6.5.1.6 Vibrator In the vibrator menu different vibrator options can be selected for the handset. The options for the handset vibrator are as showed and explained below. Off This function disables vibrator whereas the handset will not vibrate at incoming calls.
6.5.1.7 Key Sound The “Key Sound” settings controls if a key sound is heard as the keys are pressed on the handset, or if no sound is made. The following three different options can be selected for the key sounds: Silent If this feature is chosen, there will not be heard any sounds when pressing the keys on handset. Click With this function enabled a click sound is heard when a key is pressed. Tone When this options is enabled a tone will be heard when a key is pressed.
6.5.1.9 Coverage Warning A coverage warning can be set to occur when the handset is out of range of a base station in the system. When the feature “Coverage warning” is enabled (On) an audible indication is given in the earpiece of the handset when the user is close to the maximum range of the nearest base station in the system. Hereby, the user knows that the call is at the edge of the possible coverage of the call, and that the user has to move back in to coverage to keep the call going.
Noise reduction is a function used when the handset is in call. During a call if noise reduction is enabled on the handset, the background noise around the user is reduced. In this way, the user should sound clearer to the counterpart since the background noise is reduced to a minimum. 6.5.2 Time & Date To set the time and date in the handset select the “Time & date” menu. Below it is shown how the time and time format can be changed.
6.5.3 Language In this menu it is possible to select different languages for the handset. The menu tree below shows the different languages available on the handset. Settings Language English Espanol Deutsch Francais Italiano Nederlands Portugues Dansk Svenska Turkce Polski Norsk Russian-1 Russian-2 Hrvatski Srpski Slovinsky Cesky The currently applied language is displayed when highlighting the menu “Language”.
As seen in the images above each colour of the LED signal (green, yellow, and red) can respectively be configured to indicate: Missed call The LED signal blinks in the chosen colour when there is a missed call. Voice message The LED signal blinks in the chosen colour when there is a voice mail message that has not been listened to. Low battery The LED signals blinks in the chosen colour when the battery is low (below 20% battery on the handset).
6.5.6 Security In the “Security” menu it is possible to set an automatic keylock, and change the PIN of the handset. Automatic keylock If the “Automatic keylock” feature is enabled, the keypad will lock automatically after a certain amount of time that the handset has not been used. The currently applied setting is displayed when highlighting the menu “Automatic keylock”. A list of selectable timeouts is displayed when the user enters the “Automatic keylock” menu.
Settings Handset name Line Reset settings Status Handset name By selecting “Handset name” the name of the handset can be changed. As seen above, an editor is displayed when entering the menu. The handset name is typed in by using the numeric keys and afterward pressing the left softkey “Save”. The handset name is displayed in the third line of the idle display.
As it can be seen above, the handset PIN code is required to reset the handset to its default settings. After such a reset the handset is still registered. The base is not reset to default when selecting this feature. Status The menu “Status” delivers some useful information to the end user about both base station that the handset is currently using and handset status. The displayed information is as follows.
The “Auto answer” feature makes it possible for the handset to automatically answer an incoming call. This setting can be set to the following conditions: Normal With this enabled the handset does not answer a call automatically, but the user must always press the green “Off-hook” key to answer a call. The call is not answered by removing the handset from the charger.
Silent The handset receives an incoming call as normal, but it does not ring (i.e. no audio alert but the incoming call screen is displayed). 6.5.10 Do Not Disturb This “Do not disturb” feature is to be used when the handset user does not want to be disturbed. With this feature disabled, the handset reacts as normal on all incoming activity. If the function is enabled, though, the handset will not react, and the calling counterpart will be directed to voice mail if this feature is enabled.
On for next call If this function is enabled, then the caller ID will be hidden to the counterpart only for the next outgoing call, and then for the following calls the number will not be hidden anymore. Always on With the “Always on” enabled, the caller ID will be hidden for the counterpart for all outgoing calls initiated until this feature is disabled again. NOTE: When hide number enabled, base sends SIP header “Privacy: id” to address sip:anonymous@anonymous.
answered during a certain time period as for example 30 seconds. This feature is setup in the same way as “Forward Unconditionally” as displayed above. Forward Busy When “Forward Busy” is enabled the handset forwards all incoming call if the handset is busy, or if the user presses “Reject” on the call. This feature is enabled in the same way as “Forward Unconditionally” which is showed above. 6.5.
6.5.14.1 Enable/disable Bluetooth can either be enabled or disabled on the handset. The handset can only be paired with a Bluetooth device when Bluetooth is enabled. With Bluetooth enabled an icon status bar to indicate that Bluetooth is enabled on the handset. In the status bar, the Bluetooth icon is displayed in the is shown if Bluetooth is enabled, but the handset is not paired with any Bluetooth devices. This Bluetooth icon Bluetooth device. is displayed if the handset is paired with a 6.5.14.
The handset is now connected to the Bluetooth device, and audio will be routed through the Bluetooth headset in call. To inform the user that the devices are paired a Bluetooth icon in the status bar. is shown 6.5.14.3 Paired devices The handset can be paired with up to four different Bluetooth headsets. When paired with one device this is displayed, as below, in the “Paired devices” list. By using the up/down navigation key the handset can be connected to any of the paired devices.
Change Name This option changes the name of the paired Bluetooth device on the handset. In this way the handset user can change the name of the Bluetooth device to something other than the original name. Delete With this option the selected paired device can be deleted. If a paired Bluetooth device is deleted the handset will no longer be paired with this device and it will be removed from the “Paired devices” list.
6.6.1 How to Setup Text Messaging For the text messaging function to work on the handset, this needs to be enabled on the base station web interface. As seen above the text messaging feature is enabled on the handsets via “Management” on the base station web interface. With this feature enabled it is possible to send messages from one handset on the system to another handset on the system.
Additionally, it is possible to send the text messages via a text messaging server (MobiCall server) which enables handsets on different systems of base stations to send text messages to one another. When using a text messaging server for text messaging the “Text Messaging Server” and “Text Messaging Port” needs to be filled out. An example of this is seen below. For further information on the text messaging feature and setup on the base station see the base station manual via reference [3]. 6.6.
As displayed above, pressing ’New’ makes it possible to write a new message by using the keypad. The maximal message text length is 160 characters, and the number of characters typed are displayed at the bottom right corner of the text field. To choose other symbols than those available on the keypad press the middle softkey ‘Symbol’, and an amount of symbols will be available to select.
Contacts By selecting this option the contact list is displayed, and the message can be sent to one of the local contacts in the contact list. Enter number In this option it is possible to enter a number, and thereby sending a message to this number. Send to many By choosing ‘Send to many’ the message can be sent to more than one contact in the contact list without exiting from the list of contacts. This is displayed below.
are used to navigate between them. The content of these four submenus are described in the following sections. 6.6.6 Drafts ‘Drafts’ is the submenu that is opened when the ‘Messaging’ menu is selected. In this menu drafts are saved if a message has been written, but was not sent. When pressing select on a highlighted draft, this is opened according to the last time that it was edited, and it is possible to edit it, and send it again.
6.6.5.2 What is Stored in Drafts? When writing a new message and then exiting with the red on-hook key before the message is sent, this message can be saved as a draft. This is displayed below. By pressing the left softkey ‘Yes’ the message is saved as a draft, and can be opened again in the ‘Drafts’ menu. If the right ‘No’ softkey is pressed the message is not stored as a draft, and the handset returns to the previously opened menu without saving the message. 6.6.
Reply With this option it is possible to reply the counterpart to the received message. Forward By selecting ‘Forward’, the newly received message is entered again, and can be edited and forwarded to another number. Save as contact With the function ‘Save as contact’ it is possible to save the number that the message was received from in the local phonebook.
To open a sent message scroll up/down to highlight it, and then press the left softkey ‘Select’. By pressing the middle softkey, the message is opened, and it is possible to forward it to another handset than it was originally sent to. 6.6.8.1 The More Option When pressing the right softkey ‘More’ a list of options is given as seen below. 6.6.9 Settings In the ‘Settings’ menu it is possible to set messaging options on or off. These options will be described below. Version 1.
Overwrite old If this option is set to ‘On’ with the left softkey, then the oldest messages is overwritten if the maximum number of messages is reached. The maximum number of messages that can be stored in drafts, inbox, and sent messages is 250. If the number of 250 messages is exceeded, and the option is set to ‘Off’ then no new messages can be received before deleting some old messages manually.
An alarm will then occur at the time that has been set. The time can both be set with the numeric keypad, or with the up/down navigation keys. Recurrent alarm This feature enables another alarm to be set, thereby another time can be saved by pressing left softkey “Save”. In this way, two alarms can occur. The time can both be set with the numeric keypad, or with the up/down navigation keys. Snooze time The “Snooze time” indicates the time for the alarm to be snoozed when it goes off. Version 1.
This means that when the alarm occurs the user can either “Dismiss” it with the right softkey, or “Snooze” it with the left softkey. In this case the snooze time gives the time before the alarm occurs again. NOTE: If the handset is in silent mode or if the volume is set to mute then an alarm will be a silent alarm, and no sound will be heard during the alarm. The “Silent Alarm” icon will be displayed in the status bar. 6.
name and number, respectively. For the new F-key to be saved press the left softkey “Save”, and this F-key is added to F-keys. Edit F-Key This feature enables that an existing F-key can be edited, if the name or number need changing.
Running Alarm To trigger the Running Alarm the handset needs to be shaken up and down for a couple of seconds. Hereby the running alarm is triggered by running if the user has the handset in the hand or in a pocket or similar during running. Man Down Alarm The Man Down alarm is triggered if the handset is lying down in an angle from 60degrees. The time for the handset to be still before the alarm is triggered can be set on base station web interface (in reference to next chapter 6.9.
Profile Alias An alias or user-friendly name to help identify the different profiles when selecting which profiles to enable for the individual handsets. Alarm Type The type of alarm is dependent of what kind of event that has triggered the alarm on the handset. The handset supports either of the following categories: Man Down No Movement Running Pull Cord Emergency Button Disabled Alarm Signal The way the alarm is signaled as it is received on the handset.
and filling out “Text Messaging Server” and “Text Messaging Port” (see 6.6.1 How To Setup Text Messaging). 6.9.2.2 How to Configure Alarms on the Handset Afterwards for each handset in the extension page, it can be selected which of the configured alarm profiles, the given handset shall subscribe to. To configure an alarm profile for a certain handset click on the IPEI of that handset, and the following screen will appear allowing you to setup emergency settings for the handset.
To activate a certain alarm type on the handset, it must be ticked as seen above. For the handset shown above it means that Running, Pull Cord, and Emergency Button can be triggered from that handset whereas Man Down and No Movement are not ticked meaning that these alarms cannot be triggered on that handset. NOTE: After saving these emergency settings for the extension the handset or the base station must be power cycled for the changes to take effect.
The color of the alarm represents what priority the alarm has. The priority of different scenarios to start the alarm is set on the server, and it is defined what should send a green, yellow, or red alarm to the handset. Additionally, an alarm can be sent out to either one handset, or more handsets which is also defined in the server settings. Version 1.
7 Calls Operations In this section the different types of calls and call handling will be described. 7.1 Incoming call As the handset receives an incoming call an alerting screen will be displayed as displayed below. This will be accompanied by a ring signal and/or a vibrating handset according to the respective settings on the handset.
NOTE: An incoming call can also be rejected by pressing the red “On-hook” key. 7.1.3 Silencing an Incoming Call When the handset is alerting it is possible to press the left softkey “Silent” whereas the handset will continue to alert, but without any heard ringing. 7.1.4 Ending a Call To end an ongoing call press the red “On-hook” key , and the call will be terminated. The duration of the call is shown in the display.
3. The handset will show a “Calling” screen as seen above. 4. When the counterpart answers the call the screen will show “Connected”, and the two parts are now in call. 7.2.1.1 Line Call If the handset is used in a multiline environment, it is possible to make a call from different lines by pressing the middle softkey “Line”, and choose the line according to which system the call should be made from. See 7.5.6 Handset Name, Line, Reset Settings, Status.
7.3 Call Holding/Retrieving It is possible to hold a call which means that the one party of the call is put on hold and cannot hear the other party, but can only hear a repeated short tone on hold until the call is retrieved. 1. To put the counterpart of the call on hold press the left softkey “Hold”, and this party is put on hold. 2. To retrieve the call, and thereby continue the conversation, press left softkey “Retrieve” which is only showed on the screen when the other party of the call is put on hold.
2. Press the right softkey “Transfer” on either of the handsets in call, and the counterpart of the call is put on hold. 3. Enter the number that the transfer should be made to, and press the green “Off-hook” button 4. A ring back tone is heard and a third party is called. 5. As the third party answers the call the handset user initiating the transfer will show a connected screen as seen above.
1. Initiate a call with a counterpart so that the handset displays “Connected” as shown above. 2. Press the right softkey “Transfer” on either of the handsets in call, and the counterpart of the call is put on hold. 3. Enter the number that the transfer should be made to, and press transfer. 4.
5. As the second party answers the call a blue “Connected” screen as above is displayed. 6. By pressing the left softkey “Swap” the green “Connected” screen is displayed instead which indicates that the ongoing call is now between the first party whereas the second party is now put on hold. 7. From this point, it is possible to toggle between the two parties by pressing “Swap”.
This indicates that the party 2567 now has two ongoing calls with one of them on hold, and it is possible to swap between them, make a conference, or transfer one of the parties. 7.7 Conference Call In a conference call there are always at least three parties in the same conversation. Hereby, this feature enables the user to have an ongoing call with more than one person – the parties in a conference call are called participants. 7.7.
5. When the called party answers the call the second party is still on hold, and the conversation is only between the third party and the first party, i.e. initiator of the conference. 6. To start conversation between the three parties – i.e. a conference – press the middle softkey “Conf.” 7. The “Conference” screen as seen above will then be displayed, and the three participants will be in a conference call. Thereby the conversation is between all three parties.
NOTE: Different configurations on the PBX that the base system uses may result in different terminations of a conference call. E.g. the configuration of some PBX’s could cause that the whole conference call is not terminated if the initiator of the conference presses the red “On-hook” key to terminate. Version 1.
8 SD Card A SD card is an external memory card that gives the possibility of storing information from the handset externally. In this way more people can use the same handset since the SD card is the memory unit containing all individual data. The SD card can then be inserted into one handset making that your personal handset on one day, and inserted into another handset which makes that your personal handset on another day. 8.
a certain registration on a base station, inserting the SD card will make the handset use the registration from the SD card instead of its own. In this way, the information of the SD Card will always be used instead of the information of the handset when an SD card is inserted in the handset. NOTE: The SD card will never overwrite the information already on the handset, but the user will just get the information from the SD card instead of the handset when an SD card is in the handset.
9 Accessories It is possible to get different accessories to the RTX SME VoIP 8830 handset. These different accessories are listed in the following: - Dual Charger Single Charger Adapter for Charger Vertical Leather Pouch Horizontal Leather Pouch Belt Clip Swivel Belt Clip Battery Battery Cover Headset Deployment tool 3.5mm RTX2610 HS Plug version 3.5mm Version 1.
10 Troubleshooting This troubleshooting section contains information on how to solve some operational problems that you may experience on the handset. 10.1 Operational problems State: The handset does not ring Problem cause: The sound off icon is seen in the status bar; hence the handset is silent mode. Action: Increase the volume in Audio Settings, or long press the #-key in idle.
Additional handset information RTX8830 Important safety information Use Only power adaptor listed in the user instructions Charge the battery or handset only in combination with RTX8630 DECT Handset Desktop Charger and the Ten Pao S008CM0550060 adapter that comes with the product. Plug the Ten Pao S008CM0550060 AC/DC adaptor in a wall outlet socket near the equipment for easy access/removal of the AC/DC adaptor.
Dansk Undertegnede “RTX Products” erklærer herved, at følgende udstyr “RTX8830” overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF Deutsch Hiermit erklärt “RTX Products”, dass sich das Gerät “RTX8830” in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Suomi “RTX Products” vakuuttaa täten että “RTX8830” tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska Härmed intygar “RTX Products” att denna “RTX8830” står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Intended use These phones are designed for use with an RTX IP DECT phone network. Any other use is considered unintended use.
Exposure to Radio Frequency (RF) Signals This phone is a radio transmitter and receiver. It is designed and manufacturer not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on the safety standards previously set by both U.S. and international standards bodies.