User's Manual

ManualsBrandsRTX Hong Kong ManualsElectronicsDECT telephone handset and charger

Additional handset information RTX8111

Important safety information

Charge the battery or handset only in combination with RTX8111 DECT Handset Desktop Charger and the SALOM SSW-2374 or Friwo

FW7712-1 or FW7713/XX or Ten Pao S005SV0500100 or S005SB0500100 adapter that comes with the product.

Plug the SALOM SSW-2374 or Friwo FW7712-1 or FW7713/XX or Ten Pao S005SV0500100 or S005SB0500100 AC/DC adaptor in a wall outlet

socket near the equipment for easy access/removal of the AC/DC adaptor.

Important battery information

This product uses rechargeable Lithium-Ion batteries 3.7V, 1100mAh. Only use batteries that come with the handset or dedicated spare batteries

marked with “Battery Pack, CE-MB206-5C-XX or RTR001FXX”. Do not use any other type, since this may present a risk of leakage, fire, explosion or

other hazardous situation. For battery replacement or removal please remove the battery cover of the handset. Never disassemble, customize or short-

circuit batteries. Do not place battery in fire or heat the battery. Charge battery only with RTX8111 Charger and the

SALOM SSW-2374 or Friwo

FW7712-1 or FW7713/XX or Ten Pao S005SV0500100 or S005SB0500100

adapter or adaptor itself that comes with the product.

Sensitive Electronic Environment

Any radio-based equipment can potentially cause interference with other equipment and can be interfered from other equipment. This also applies for

DECT equipment. However due to the very low transmission power level the chances for interference are very small. Research proves that

operational DECT phones normally don’t influence electronic equipment however some precautions must be taken into account for sensitive

electronic equipment e.g. sensitive laboratory equipment. When DECT phones operate in straight nearness of sensitive electronic equipment

incidental influence can appear. You are advised not to place the DECT phone on or close (less than 10cm) to this kind of equipment, even in standby

mode. Please also use the other documentation supplied with the various parts of your telephone system.

Product disposal information

For countries in the European Union

The symbol depicted here has been affixed to your product in order to inform you that electrical and electronic products should not be disposed

of as municipal waste.

Electrical and electronic products including the cables, plugs and accessories should be disposed of separately in order to allow proper treatment, recovery

and recycling. These products should be taken to a designated facility where the best available treatment, recovery and recycling techniques are available.

Separate disposal has significant advantages: valuable materials can be re-used and it prevents the dispersion of unwanted substances into the municipal

waste stream. This contributes to the protection of human health and the environment.

Please be informed that a fine may be imposed for illegal disposal of electrical and electronic products via the general municipal waste stream. In order to

facilitate separate disposal and environmentally sound recycling, arrangements have been made for local collection and recycling. In case your electrical

and electronic products need to be disposed of please refer to your supplier or the contractual agreements that your company has made upon acquisition of

these products.

For countries outside the European Union

Disposal of electrical and electronic products in countries outside the European Union should be done in line with the local regulations. If no arrangement

has been made with your supplier, please contact the local authorities for further information.

Battery disposal information

Defect or exhausted batteries should never be disposed of as municipal waste. Return old batteries to the battery supplier, a licensed battery dealer or a

designated collection facility. Do not incinerate batteries.

Regulatory information Europe

Declaration of conformity

Česky

“RTX Telecom”

tímto prohlašuje, že tento “RTX8111” je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk

Undertegnede “RTX Telecom” erklærer herved, at følgende udstyr “RTX8111” overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Deutsch

Summary of content (41 pages)

PAGE 1
Additional handset information RTX8111 Important safety information Charge the battery or handset only in combination with RTX8111 DECT Handset Desktop Charger and the SALOM SSW-2374 or Friwo FW7712-1 or FW7713/XX or Ten Pao S005SV0500100 or S005SB0500100 adapter that comes with the product. Plug the SALOM SSW-2374 or Friwo FW7712-1 or FW7713/XX or Ten Pao S005SV0500100 or S005SB0500100 AC/DC adaptor in a wall outlet socket near the equipment for easy access/removal of the AC/DC adaptor.
PAGE 2
Hiermit erklärt “RTX Telecom”, dass sich das Gerät “RTX8111” in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti Käesolevaga kinnitab “RTX Telecom” seadme “RTX8111” vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
PAGE 3
Defect or exhausted batteries should never be disposed of as municipal waste. Return old batteries to the battery supplier, a licensed battery dealer or a designated collection facility. Do not incinerate batteries. RTX Telecom A/S Stroemmen 6 9400 Noerresundby Denmark Regulatory information United States Interference information: This device complies with Part 15 of the FCC Rules.
PAGE 4
Exposure to Radio Frequency (RF) Signals L'exposition à la radiofréquence (RF) This wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limit for exposure to radio frequency (RF) energy set by the Ministry of Health (Canada), Safety Code 6. These limits are part of comprehensive guidelines and established permitted levels of RF energy for the general population.
PAGE 5
First Alcatel-Lucent 8232 DECT Handset OmniPCX Enterprise 8AL90862USAAed00B Draft 13 april 2012
PAGE 6
Contents Contents Precautions for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 4 Toc 1. Getting to know your telephone 1.1 Phone description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Status icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 MENU icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 7
9. Using the telephone in GAP mode 9.1 Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 Receiving a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 Calling from your personal directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4 Redialling the last number dialed (redial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.
PAGE 8
Precautions for use Coverage area The DECT functions provided by your Alcatel-Lucent system allow user mobility management via DECT cordless telephones. Radio coverage of the Alcatel-Lucent system is ensured by a network of radio terminals. The coverage area of a radio terminal is called a cell. howtoc • Mobility: A user can make or receive calls in any cell. • Radio transfer: This function enables the user to move during a conversation and go from one cell to another.
PAGE 9
Precautions for use • • • • • • • • Operating conditions This approved DECT telephone is intended to be used with an Alcatel-Lucent cordless PBX. The following conditions must be respected, notably concerning the use of radioelectric frequencies: dect equipment can only be used to establish links between fixed points if these links are temporary and the equivalent isotropically radiated power at the antenna is less than 250 mw.
PAGE 10
Getting to know your telephone 1 Other 1.
PAGE 11
1.2 Status icons The status icons are displayed on the welcome screen and indicate the status of the telephone.
PAGE 12
1.4 Call icons Making a call Receiving a call Call on hold Accessing the directories Transferring a call Switching to DTMF signals Setting up a conference Diverting your calls to your voice message service Putting on common hold Parking an external communication Call duration and cost Additional options (Features depending on the system) In the event of a multiple call, the icons are given indices to represent the different correspondents 1.
PAGE 13
Getting started 2 Other 2.1 Installing the battery in the telephone • Installing the battery in the telephone Position the battery "connectors" side as shown in the drawing (A). Terminate the installation of the battery in its compartment by pressing as shown in the drawing (B). Replace the cover. • To remove it Lift up the cover. 2.2 Remove the battery from its compartment as shown in the drawing.
PAGE 14
2.3 Switching on your telephone Your telephone is switched on Press the switch on/off key If the display fails to light up or the battery icon is flashing, recharge the battery. If the radio reception icon doesn’t appear on the telephone display: • Check that you’re in an area covered (if you’re not, move close to a radio terminal). • Check that the telephone is properly installed in the system (consult the PABX manager).
PAGE 15
Using your telephone 3 Other 3.1 Making a call • dial • send the call You are in communication • hang up To make an external call, dial the outside line access code before dialing your contact number 3.2 Calling from your personal directory • access menu • contacts • personal dir validate access to the personal directory • select the name of the person you wish to call • send the call Quick access: 3.
PAGE 16
3.4 Receiving a call You are receiving a call: • answered incoming calls • disabling the ringer:press the hang up key when your telephone rings: it is still possible to answer by pressing the unhook key. Speak • hang up The ringer does not ring if: . the vibrator is active, the vibrator active icon is displayed on the screen saver. . the ringer is disabled, the ringer disabled icon is displayed on the screen saver. 3.
PAGE 17
3.
PAGE 18
During a conversation 4 Other 4.1 Make a second call You are in conversation with one correspondent • dial the number • send the call • the first call is on hold • Recover the correspondent on hold • hang up Your telephone rings • recover the correspondent on hold You can also initiate a second call by first validating the 'Other call' option and using the personal directory or the company directory. 4.
PAGE 19
4.4 Transferring a call During a conversation, to transfer the call to another number: You are in communication with a first correspondent • call the recipient of the transfer • send the call You are in conversation with the destination number • transfer the two correspondents are connected After dialling the number of the recipient, you can transfer your call directly without waiting for your correspondent to answer by selecting 'Transfer'.
PAGE 20
To recover your parked call: • access menu • services • services • pick-up services • Park/retrieve You are on a call If the parked call is not recovered within a preset time (by default 1 minute 30), it is directed to the operator. 4.
PAGE 21
Sharing 5 Other 5.1 Answering the general bell When the operator is absent, incoming external calls are diverted to a general bell. You can answer these calls: • access menu • services • services • pick-up services • Night pick up 5.2 Call pick-up You hear a telephone ringing in an office where no-one can answer. If authorised, you can answer the call on your own telephone.
PAGE 22
Temporary exit from your hunting group / Return into your group: • access menu • services • services • • • • 5.4 divers services Hunting grp in / Hunting grp out your group number apply Sending a written message to an internal correspondent • access menu • messages • text msg • Confirm • send a message? • Confirm • dial the number of your correspondent (dial, directories, last numbers dialed...
PAGE 23
5.
PAGE 24
Keep in touch 6 Other 6.1 Diverting calls to your voice mailbox • access menu • forward. • fw immediate voice mail. • Confirm 6.2 Consulting your voice mailbox When you have received a message, the Message icon is displayed on the welcome screen. The red LED on your telephone flashes to indicate there is a message.
PAGE 25
6.4 Define an overflow number When your set is not available, outside the coverage area or not working, calls to your set will be automatically forwarded to this number if it has been defined. • access menu • services • overflow • apply • modify / delete • dial the number of your correspondent (dial, directories, last numbers dialed...) • confirm 6.
PAGE 26
Fwd on Busy When you are in conversation, all your calls are diverted to the number you choose.
PAGE 27
Programming your telephone Other 7.1 Initializing your voice mailbox • you can use the message icon on the welcome screen to initialize your voice mailbox. OR • access menu • messages • voice mails • confirm access to the voice mailbox • enter your temporary password • enter your new password • record your name • end of recording • follow the instructions of the voice guide 7.2 Modifying your personal code Your personal code is used to access your voice mailbox and to lock your telephone.
PAGE 28
• Choose the tune • ring melody • select the melody of your choice • apply • Adjusting the ringer volume • level • select the volume of your choice • apply • You can adjust the buzzer/ringer mode according to your needs • press on the ringer/vibrator key • off:ringer and buzzer are deactivated • Ring only:rings only • Vibrate and ring:vibrates before ringing • Vibrate only:vibrates only • Vibrate & Ring:vibrates and rings simultaneously This key can be used to switch rapidly from the ringer to the vibrator
PAGE 29
*You can activate or disable the following functions: Handset name Status Ascending ringing Coverage warning Keypad tone Headset mode Economy mode Vibrator Security Reset settings 7.
PAGE 30
7.8 Modifying a card in the personal directory • access menu • contacts • personnal dir • select the card to be modified • apply • modify • • • • modify the name apply modify the number apply Use the browser to position on the character or digit to modify. To delete a character, briefly press the delete key ; to erase a field full of characters, hold down the erase key (long press). 7.
PAGE 31
If you do not validate the answer to the first call-back, a second call-back will be made. After a second call-back with no answer, the call-back request will be cancelled. If your line is forwarded to another set, the appointment reminder will not follow the forwarding To cancel your appointment call-back request: • access menu • alarms • cancel appointment • where appropriate, dial the number of the destination set • apply 7.
PAGE 32
Registering the telephone Other 8.1 Registering the telephone on a system for the first time For the mobile telephone to function, it must be registered on at least one Alcatel-Lucent or GAP system (registration operation).If when first switched on the display indicates: 'System 1 Auto install ?' your telephone has not been registered on any system; consult your installation technician or proceed as follows:1. Prepare your system for registration (see system installation guide).2.
PAGE 33
• access menu • install • register • enter the pin code • apply • select a system • • • • enter park code apply enter access code apply • select power mode Launch subscription • return to idle If the registration operation runs correctly (Subscription accepted), the telephone is ready for use, and the radio coverage icon appears. If the registration operation has not been successful, the station proposes launching the subscription again.
PAGE 34
Using the telephone in GAP mode Your telephone complies with the GAP standard and can be used in simplified mode on another DECT/GAP system (other PABX or indoor relay unit). Unless otherwise specified, the functions described below are available on your telephone in combination with the mandatory functions provided by your fixed GAP system. Automatic transfer between radio cells: This telephone function enables you to move around between radio relay units, without any break in communications.
PAGE 35
9.4 Redialling the last number dialed (redial) • long press OR • access menu • call log • select the name of the person you wish to call • send the call 9.5 Sending DTMF signals During a call, you sometimes have to send DTMF signals, for example, for a voice message service, an automatic switchboard or when remotely consulting an answering machine. To do this: Press the star key (hold down for a few seconds). 9.
PAGE 36
• Modify a contact • select the card to be modified • edit OR • select the type of contact work / mobile / home • edit contact • name: • enter the name (10 characters maximum) • apply • select the type of contact work / mobile / home • enter the number • apply • save • yes To delete a character, briefly press the delete key. ; to erase a field full of characters, hold down the erase key (long press). 9.
PAGE 37
Adjusting the ringer volume: • access menu • ring • ring volume • apply • increase / reduce the volume • apply • return to idle Selecting language: • access menu • settings • language • Select the language of your choice • apply • return to idle Other features: • access menu • Ring • • • • • • • Vibrator: to adjust the ringer and/or the vibrator Keypad tone: activate or deactivate the keypad tone Confirmat.
PAGE 38
Accessories 10 Other 10.1 Phone package When you purchase your phone, it is equiped with a clipbelt installed on its back. You can uninstall this clipbelt and replace it by the cap provided in the box of your new phone. • turn the clipbelt by doing a counterclockwise quarter turn • Uninstall the clipbelt by pulling it towards you. Place the cover to put in place of clipbelt such as described on the picture. Push the cover towards the back of the phone until the cover is clipped. 10.
PAGE 39
10.3 Characteristics of the mains power adapter input: 100/240 V - 50/60 Hz Output: 5V - 1A The mains power socket used must be close to the charger/holder and easily accessible, so that it can be used as an 'on/off' facility. 10.
PAGE 40
Glossary 11 Call transfer Function enabling a call to be transferred to another telephone within the system. Common directory: This directory contains all the speed-dial numbers accessible to the users of the France Télécom diatonis system. Conference: The conference function allows the user, in contact with two correspondents, to set up a three-way conference. DECT: European cordless telephone standard: Digital Enhanced Cordless Telecommunication.
PAGE 41
Declaration of compliance Safety Instructions 7KLV DSSURYHG '(&7 WHOHSKRQH LV LQWHQGHG WR EH XVHG ZLWK DQ $OFDWHO /XFHQW FRUGOHVV 3%; 7KH IROORZLQJ FRQGLWLRQV PXVW EH UHVSHFWHG QRWDEO\ FRQFHUQLQJ WKH XVH RI UDGLRHOHFWULF IUHTXHQFLHV ವ &KDQJHV RU PRGLILFDWLRQV WR WKH HTXLSPHQW QRW H[SUHVVO\ DSSURYHG E\ WKH SDUW\ UHVSRQVLEOH IRU FRPSOLDQFH FRXOG YRLG WKH XVHUಬV DXWKRULW\ WR RSHUDWH WKH HTXLSPHQW ವ 7R OLPLW WKH ULVN RI LQWHUIHUHQFH SHRSOH ZLWK SDFHPDNHUV PXVW NHHS WKH ZLUHOHVV WHOHSKRQH DZD\ IURP WKHLU