Data Sheet TMR7 Smart
TMR7 Smart Touch Screen • AES3 I/O via XLR • Highly Flexible Screen-Layout • 2 x 2-ch. PPM/True Peak • 2 Audio Vectorscopes Loudness acc. to all relevant standards • LRA • SPL-Meter • RTA • Moving Coil • Loudness Chart The four audio inputs provided by the two AES3 XLR ports are flexibly configurable for mono or stereo sources, providing separate instruments for each source. This allows e. g. in radio broadcast the parallel monitoring of the on-air signal and a separate source.
Hardware Configuration • TMR7 Smart in a sturdy table-top frame with movable tablestand and power supply. • Resisitive 7“ touch screen 16 : 9 TFT (800 x 480 pixel) • 4-channel audio interfaces (2 x AES3 inputs via XLR-F and 2 x AES3 outputs via XLR-M) • Connectors for Ethernet, 2 x USB 2.0, GPIO, 24 V DC • Integrated Smart software package • Highly flexible screen layout options with scalable instruments Main Unit with Interfaces © 09/2017 | Technical changes without notice. | RTW GmbH & Co.
Software Smart Software Package With the integrated Smart software package, TMR7 Smart is fully equipped. It provides a wide range of RTW‘s approved loudness and audio metering tools to meet the demands of a wide variety of applications.
Dimensions TMR7 Smart Table-top unit 1 | Front view (dimensions in mm) 2 | Side view (dimensions in mm) 3 | Rear view (dimensions in mm) © 09/2017 | Technical changes without notice. | RTW GmbH & Co.KG | Am Wassermann 25 | 50829 Köln | Fon +49 221. 70 913-0 | Fax +49 221. 70 913-32 | rtw@rtw.com | www.rtw.
Connection Connectors ATTENTION! - For operating the TMR7Smart an adapted mains adapter is required. RTW recommends the use of the RTW wide voltage power supply 1178-R (100 - 240 V AC/24 V DC, 2.7 A). This power supply is included in the TMR7 Smart package. 4-pin locking low voltage connector without function AES3 In 1 (XLR-F) AES3 Out 1 (XLR-M) AES3 In 2 (XLR-F) AES3 Out 2 (XLR-M) 1 1 2 2 24 V DC, 1 A LAN GP IO (RJ-45) (RJ-12) USB A 2.
Pin Assignment AES3 In 1, AES3 In 2 (transformer-balanced, 3-pin XLR-F) LAN Pin: Function: RJ-45 standard network connector (10/100 MBit) 1 2 3 Shield/case +, hot –, cold Pin 1 Pin 2 Pin 3 (External view of the connector) NOTE - The AES3 inputs are permanently terminated with110 . GP IO (RJ-12 6P6C socket) External control of functions and presets recall as defined in the Global Keyboard menu. The inputs defined as „active low“ have to be switched against 0 V (Pin 1).
Specifications System General Power requirements: Current drain: Power dissipation: Display: Connectors: Dimensions (W x H x D): Weight: Operating temperature: +24 V DC (external 2 A max. overcurrent protective device shall be installed!) 1 A nominal, 2.5 A power-up current (10 μsec.) approx. 8,5 W (w/o SDI), approx. 11 W (with SDI) 7’’ TFT touch screen 16 : 9 (800 x 480 pixel) 1 x 4-pin locking low voltage connector type Binder 710 (DC) 2 x USB A; USB 2.
Specifications (continued) Audio Vectorscope Display mode: Inputs: AGC: Grid: AES3 Status Monitor Display: 2-channel L/R (Stereo signal with the input channels of the selected audio group) fast/slow L/R or M/S • channel data are displayed as plain text, hex or binary • Channel selectable • Audio bit activity • Hardware status Global Keyboard The Global Keyboard is used for simultaneous control of defined functions in multiple instruments, and for preset recall.
Specifications (continued) Loudness Range Instrument (LRA) Display: Graphical display of the Loudness Range Mode: selectable: LRA Bar, MagicLRA, MagicLRA + I, MagicLRA + I + Num Scale range: selectable: 6 LU, 10 LU, 20 LU, 30 LU LRA low range: 2 LU; adjustable from 1 to 20 LU in steps of 1 LU Comfort zone: 4 LU; adjustable from 1 to 20 LU in steps of 1 LU LRA high range: depends on the selected scale range and the spread of the comfort zone Colors: selectable for each range SPL Meter Mode Display: Referenc
Specifications (continued) Loudness Chart Instrument Time Select: Functions: • Horizontal running bargraphs (Timeline Bars) with individual selected colors for evaluating the common quality of Loudness values TP, M, S, I • Coordinate system displaying a graph with Tolerance Levels: the course over time of one measured value - TP Headroom: • Position of the Relative Gate switchable • Adjustable time ranges - TP Operation Range: • Selection of time periods for analyzing • Vertical Integrated bargraph switchab
Overview TouchMonitor TMR7 Smart table-top unit • Table-top unit with easy-to-use graphical interface, high-quality 7“ touch screen 16 : 9 TFT, integrated audio interface, Ethernet, 2 x USB, GPIO, 24 V DC, table-stand, mains adapter. • Smart software package with precise signal processing, functions for control, comprehenisve range of RTW‘s approved loudness and audio metering tools, and flexible display options Order number: TMR7S Audio Interfaces (I/O Options) max.
