Data Sheet TouchMonitor TM3 Smart
TouchMonitor TM3 Smart Flexible touch screen layout • Loudness: EBU, ITU, ATSC, ARIB, OP-59, AGCOM, CALM • LRA • PPM/True Peak SPL • Stereo/6-channel operation • Dialnorm • Audio: Analog, S/PDIF, AES3 • Moving Coil • Timecode • Chart TouchMonitor TM3 Smart (TM3S) is an exceptionally budget-friendly metering solution for applications including editorial working environments, edit suites and smaller control rooms, to name but a few. It consists of a display unit with 4.
Hardware TM3 Smart (TM3S) • 6-channel version for Peak, TruePeak, correlation and Loudness measurements, equipped with all licences • Table-top unit with display unit and remote interface box (cable length 2 m), with mains adapter • 4.3“ touch screen (272 x 480 pixel) • Loudness metering acc. to EBU R128, ITU-R BS.
Software Smart Software Package With the integrated Smart software package, TM3 Smart (TM3S) is fully equipped. It provides the wide range of RTW‘s approved loudness and audio metering tools to meet the demands of a wide variety of applications.
Smart Software Package (continued) The Timecode Reader instrument is used to decode and to display an LTC timecode of an external analog or digital source for the use with Loudness applications. AES Status monitor for displaying various parameters of AES3 digital audio signals in plain text. Additional control keys for positioning on the display. Global Keyboard with definable on-screen keys for simultaneous control of defined functions in multiple instruments, and for preset recall.
Dimensions Display Unit TouchMonitor TM3 Smart 21 [0.83”] Active Area 4.3 inc h 95.04 [3.74”] 138 [5.43”] 82.5 [3.25”] 53.86 [2.12”] 15° 50 [1.97”] 1 | Front view 2 | Side view Interface Box TouchMonitor TM3 Smart 146 [5.75”] 2 | Side view (right) 2 [0.08”] 85 [3.35”] 27 [1.06”] 85 [3.35”] Dimensions in mm [inch”] Common tolerance: ±0,5 mm [±0.02”] 1 | Top view 6 4 | Rear view 2 [0.08”] 2 [0.08”] 3 | Side view (left) 27 [1.06”] 146 [5.75”] 27 [1.06”] 85 [3.
Dimensions (continued) Option TM3-2U 5 [0.2“] 1 | Front view 77 [3.03“] 5 [0.2“] 82 [3.23“] Ø 3.5 [0.14“] Ø 3.5 [0.14“] 82 [3.23“] 41 [1.61“] (can only be ordered together with a TM3S – allows mounting into front panels/mounting plates or into optional 19“/2U rack carrier/mounting frame TM3-MA2U) 20.7 [0.81“] 160 [6.3“] [0.12“] 3 17.7 [0.7“] 150 [5.9“] 2 | Side view 125.3 [4.93“] Dimensions in mm [inch”] Common tolerance: ±0,5 mm [±0.02”] 77 [3.03“] 2 [0.08“] 3 [0.
Dimensions (continued) Option TM3-MA2U (separate available 19“/2U rack carrier/mounting frame for mounting up to two TM3S equipped with TM3-2U option) Dimensions in mm [inch”] Common tolerance: ±0,5 mm [±0.02”] 22 1.5 [8. 72 “] 47 U . ) [3 .2 88 (2 “] “] 19 6[ 2. 48 1 | Schematic diagram of mounting a TM3S with option TM3-2U into 19“/2U rack carrier TM3-MA2U 8 © 03/2018 | Technical changes without notice. | RTW GmbH & Co.KG | Am Wassermann 25 | 50829 Köln | Fon +49 221.
Connection Connectors ATTENTION! - For operating the TM3 Smart (TM3S), an appropriate mains adapter is required. RTW recommends the use of the RTW wide voltage power supply 1178-R (100 - 240 V AC/24 V DC, 2.7 A) approved for TouchMonitor. This power supply is included in the TM3 Smart (TM3S) package.
Pin Assignment Analog In L, Analog In R (unbalanced, RCA-F) Sub-D connector (25-pin Sub-D-F) Pin: Function: Pin: Function: Pin: Ring: Signal Shield/chassis Pin Ring (External view of the connector) NOTE - The input sensitivity for 0 dB reading is adjustable in the range from 150 mV to 30 V. While using the RCA connectors, the corresponding inputs of the SubD connector cannot be used.
Specifications System General Power requirements: Current drain: Display: Connectors: Dimensions (W x H x D): Weight: Operating temperature: Analog Inputs +24 V DC (external 2 A max. overcurrent protective device shall be installed!) 160 mA nominal, power-up current is much higher Capacitive 4.3’’ touch screen (272 x 480 pixel) 1 x 4-pin locking low voltage connector type Binder 710 (DC) 1 x USB Mini-B; USB 2.
Specifications (continued) PPM/True Peak Display General Input sources: Peakmeter: Display: Functions: Analog Peakmeter Analog scales: Integration time: Peak hold indicator: Integration time (Attack): analog and/or digital 2-ch. Stereo to 6-channel (Multichannel, 5.1) • Peak level • Peak hold (selectable color) • Numerical value of the display • Gain (+20 dB, +40 dB acc. to standard) • Peak hold on/off • Memory • Reset • DIN5: +5 .. -50 dB, • Nordic: +12 .. -42 dB, • BR IIa: 7 ..
Specifications (continued) Customer Specific Loudness Mode Display: • Bargraphs for each single channel (can be combined with PPM bargraphs) • M bargraph (Momentary value) • S bargraph (Short - shortterm value) • I-Bargraph (Integrated - long term value) • Red scale markers for 0 LU thresholds Numerical display: • Short, Integrated, Momentary, LRA values • Maximum values for True Peak (TPmax), Momentary (Mmax), Short (Smax) • Duration of Integrated measurment (I-time) Scales: *) Loudness scales: • EBU+9: +9
Specifications (continued) Timecode Reader Decoding and display of LTC timecode. Display: Mode: Input: Colors: numerical display of LTC (from analog or digital sources) LTC (fixed), instrument selectable when creating a Non-Audio group one analog or digital channel selectable selectable, 32 colors PPM + Loudness: - Ch.
Specifications (continued) Items of Delivery TM3 Smart (Table-top unit): TM3 Smart (Panel-mount unit): Optional Accessories • 2-ch. Stereo to 6-channel (Multichannel, 5.1) • Smart Software Package with all instruments as described in Software section • TM3 display unit with 4.3“ touch screen in a table-top case with fixed connector cable (approx. 2 m) • Interface box, connected with display unit • Mains adapter, manual Order no.
Block Diagram © 03/2018 | Technical changes without prior notice. RTW GmbH & Co. KG Am Wassermann 25 | 50829 Köln | Germany Fon: +49 221. 70 913-0 | Fax: +49 221. 70 913-32 Internet: www.rtw.com | E-Mail: rtw@rtw.
