Specifications

ManualsBrandsRTS ManualsOtherXCP-48-RJ45

90000253_E

Including all PortServer TS, Digi Connect,

and Digi One Products

Cable Guide

Summary of content (152 pages)

PAGE 1
Cable Guide Including all PortServer TS, Digi Connect, and Digi One Products 90000253_E
PAGE 2
 Digi International Inc. 2005. Digi, Digi International, the Digi logo, the Making Device Networking Easy logo, Digi One, Digi Connect, PortServer TS, and RealPort are trademarks or registered trademarks of Digi International, Inc. in the United States and other countries worldwide. All other trademarks are the property of their respective owners.
PAGE 3
Ta b l e o f C o n t e n t s Chapter 1 EIA-232 Asynchronous Interface General EIA-232 Cable Information ...................................................... 9 Physical Cable Characteristics ................................................................... 9 Grounding Requirements............................................................................ 9 Environmental Requirements ..................................................................... 9 Data Rate Information.............................
PAGE 4
Chapter 4 EIA-232: RJ-45 to DB-25 Digi RJ-45 Connector Pin Assignments .............................................. 21 RJ Connector Types............................................................................ 21 Digi RJ-45 to DB-25/DB-9 Cable Adapters.......................................... 22 Part numbers for RJ-45 to DB-25 Cable Adapters: .................................. 22 Part numbers for RJ-45 to DB-9 Cable Adapters: ....................................
PAGE 5
RJ-45 Pinouts ........................................................................................... 34 DB-9 Pinouts............................................................................................. 34 RJ-45 8 Pin EIA-485 Multi-drop Mode ...................................................... 35 Chapter 7 DataFire 2000 Sync Adapter Introduction.......................................................................................... 37 Features................................................
PAGE 6
Modem Adapter ........................................................................................ 67 Digi One, PortServer TS, and Multi-Port Serial Cards RJ-45 to DB-9M Modem Adapter ........................................................................................ 68 Digi One, PortServer TS, and Multi-Port Serial Cards RJ-45 to DB-25M Printer Adapter.......................................................................................... 69 Digi CM RJ-45 to DB-9F DTE RS-232 Crossover Cable ....
PAGE 7
SCSI Terminal Server DB-25M to DB-25F Terminal Emulator Cable..... 113 RJ-11 6 Pin/4-Wire to DB-9F Terminal Emulator Cable ......................... 114 RJ-11 6 Pin/4-Wire to DB-25F Terminal Emulator Cable Software Flow Control Only ............................................................................................ 115 RJ-11 6 Pin to DB-9F Terminal Emulator Cable ..................................... 116 RJ-11 6 Pin to DB-25F Terminal Emulator Cable ...................................
PAGE 8
Contents
PAGE 9
EIA-232 Asynchronous Interface Chapter 1 General EIA-232 Cable Information Use this information to determine the proper EIA-232 cable requirements for your application. Physical Cable Characteristics EIA-232 serial interface cables should be shielded, low capacitance cables, designed specifically for serial data transmission. Grounding Requirements EIA-232 interface cables should have the shield grounded at both ends of the cable.
PAGE 10
• • In situations where low-capacitance cable is unavailable, or very long cable runs are required, "short-haul" modems can be used to increase the effective range of the EIA-232 interface. Short-haul modems are similar to standard modems, except that they are connected directly to each other via a cable instead of going through a telephone circuit. Use only externally-powered short-haul modems with Digi products.
PAGE 11
EIA-232: DB-25 to DB-25 Chapter 2 Digi DB-25 Connector Pin Assignments Signal Description DTE Use Pin # GND Chassis Ground N/A Shell TxD Transmitted Data Output 2 RxD Received Data Input 3 RTS Request to Send Output 4 CTS Clear to Send Input 5 DSR Data Set Ready Input 6 SG Signal Ground reference 7 DCD Data Carrier Detect Input 8 DTR Data Terminal Ready Output 20 RI Ring Indicator Input 22 DB-25 Software Handshaking (XON/XOFF) Cable The following three-wire cable
PAGE 12
Terminal/Printer Cable with DTR Handshaking DB-25 Female (Digi End) Signal Pin TxD 2 RxD DB-25 Male (Peripheral) Pin Signal connected to 3 RxD 3 connected to 2 TxD CTS 5 connected to 20 DTR SG 7 connected to 7 SG GND Shell connected (via shield) to Shell GND jumpered 4+5 RTS+CTS Note: Some terminal or printer manufacturers may use different methods of flow control. Consult your documentation for specific wiring requirements.
PAGE 13
DB-25 Fully-Wired Terminal/Printer Cable The following cable wiring supports most serial terminals or printers with either software or hardware handshaking. This cable is valid with any Digi DB-25 serial port.
PAGE 14
Chapter 4 EIA-232: DB-25 to DB-25
PAGE 15
Chapter 4 EIA-232: DB-25 to DB-25 15
PAGE 16
Cable-to-Adapter Cross Reference For Digi One, PortServer TS, PortServer II, and Multi-Port Adapters with RJ-45 connectors RJ45 to ___ Male or Female Straight or Crossover Application DB9 F Crossover Bay Accelar, Nortel and other DB9 DTE devices Cable or Adapter Part Number Cable Identifier Cable 76000645 (4’) 61090048 76000697 NA Cable 76000264 (4’) 61080048 Adapter none NA 76000200 (2’) 61070024 76000201 (4’) 61070048 none NA 76000239 (2’) 61060024 76000240 (4’) 61060048 7
PAGE 17
EIA-232: DB-9 Chapter 3 Digi DB-9 Connector Options: AccelePort Xr, Xe, ClassicBoard Fan-Out Cables AccelePort and ClassicBoard adapters may be equipped with a fan-out cable consisting of a single DB-78M connector at the adapter end, and four or eight DTE-wired DB-9 male or female connectors at the peripheral end. Note: IMPORTANT! The Digi Neo and AccelePort Xp families use different cable assemblies from those used with ClassicBoard and other Digi adapters (AccelePort Xr, Xe, PC/X).
PAGE 18
Connector Boxes Digi connector box assemblies consist of a single HD-68M connector at the adapter end, connected by a 6-foot cable to a connector box equipped with four or eight DTE-wired DB-9 male connectors. AccelePort 16p adapters have two connectors, which may be connected to two 8-port boxes or a 16port rack-mount box. AccelePort 16p adapters include two 10-foot cables. 10-foot cables may be ordered as an upgrade option for 4- and 8-port adapters.
PAGE 19
DB-9 4-Wire Hardware Handshaking (DTR) Cable The following four-wire cable is often sufficient for a terminal, printer, or other DTE device configured for DTR (hardware) flow control. However, some terminals and printers may have other cable requirements. Consult your terminal or printer manual for this information. For more universal compatibility, use a fully-wired DB-9 terminal/printer cable .
PAGE 20
Terminal/Printer Cable for Software (XON/XOFF) or Hardware (RTS/CTS) Handshaking DB-9 (Digi End) Signal DB-9 Male (Terminal/Printer) Pin Pin Signal DCD+DSR 1+6 connected to 4 DTR RxD 2 connected to 3 TxD TxD 3 connected to 2 RxD DTR 4 connected to 1+6 DCD+DSR SG 5 connected to 5 SG RTS 7 connected to 8 CTS CTS 8 connected to 7 RTS GND Shell connected to Shell GND Note: Important: Other printer manufacturers may use different methods of flow control.
PAGE 21
EIA-232: RJ-45 to DB-25 Chapter 4 Digi RJ-45 Connector Pin Assignments 10 pin RJ-45 plugs may be difficult to obtain in the retail market; therefore, most Digi device driver software incorporates an optional feature called ALTPIN, which swaps the logical functions of DSR (Data Set Ready) with DCD (Data Carrier Detect). When ALTPIN is enabled, DCD becomes available on pin 1 of an 8 pin RJ45 connector (equivalent to pin 2 of a 10 pin connector).
PAGE 22
7 SG 7 6 5 8 CTS 8 7 6 9 DTR 9 8 10 DCD (DSR*) *When ALTPIN is in effect. 10 4 Digi RJ-45 to DB-25/DB-9 Cable Adapters RJ-45 to DB-25/DB-9 cable adapters can be purchased from Digi. These adapters consist of a 10 pin RJ-45 plug connected via a two- or four-foot cable to a DB-25 or DB-9 connector. The adapters are fully-wired and provide modem control.
PAGE 23
Part numbers for RJ-45 to RJ-45 8 pin Crossover Cable for Cisco & Sun Netra: Cable Description Order # Number found on Cable Cable RJ45 to RJ45 8 pin (single pack) 76000631 63000222-02 Cable RJ45 to RJ45 8 pin (bulk pack of 8) 76000632 63000222-02 Cable RJ45 to RJ45 8 pin (bulk pack of 16) 76000633 63000222-02 RJ-11 Software Handshaking (XON/XOFF) Cable The following 3-wire cable is often sufficient for a terminal, printer or other DTE device configured for software flow control.
PAGE 24
Terminal/Printer Cable with DTR Handshaking RJ-45 (Digi End) Signal Pin TxD 4 RxD DB-25 Male (Peripheral) Pin Signal connected to 3 RxD 5 connected to 2 TxD CTS 7 connected to 20 DTR SG 6 connected to 7 SG GND 3 connected (via shield) to 1 (or shell) GND jumpered 4+5 RTS+CTS Note: Some terminal or printer manufacturers may use different methods of flow control. Consult your documentation for specific wiring requirements.
PAGE 25
Using an 8 pin RJ-45 plug, the following cable wiring supports most serial terminals or printers with either software or hardware handshaking using the Digi ALTPIN option. Most terminals and printers use Request to Send/Clear to Send (RTS/CTS) for hardware handshaking. The cable shown supports this method.
PAGE 26
Terminal/Printer Cable for Software (XON/XOFF) or Hardware (RTS/CTS) Handshaking RJ-45 10 pin (Digi End) - Signal Pin DSR+DCD* * ALTPIN must be turned off for DCD to be on pin 10 2+10 RTS Note: DB-25 Male (Terminal/Printer) Pin Signal connected to 20 DTR 3 connected to 5 CTS GND 4 connected (via shield) to Shell GND TxD 5 connected to 3 RxD RxD 6 connected to 2 TxD SG 7 connected to 7 SG CTS 8 connected to 4 RTS DTR 9 connected to 6+8 DSR+D CD Some terminal or
PAGE 27
When ALTPIN is enabled, DCD becomes available on pin 1 of an 8 pin RJ45 connector (equivalent to pin 2 of a 10 pin connector). Note: ALTPIN is not supported for the PortServer product under Windows NT. Use a full 10-wire modem cable in this case. RJ-45 10 pin Plug to DB-25 Modem Cable The simplest way to connect a modem to a Digi RJ-45 jack is to use a Digi RJ-45 to DB-25 Cable Adapter. The following table shows how to apply the adapter wiring scheme to custom modem cables.
PAGE 28
Pin Positions for RJ-45 28 Chapter 6 EIA-232: RJ-45 to DB-25
PAGE 29
Chapter 5 EIA-422 Asynchronous Interface General EIA-422 Cable Information This section applies to Digi products equipped with EIA-422 asynchronous interfaces. Physical Cable Characteristics EIA-422 interface cables should be shielded twisted-pair cables. Each signal requires two leads (one twisted pair of wires) to complete a balanced voltage digital circuit. The shield should be connected to the Chassis Ground of the devices at both ends of the interface cable.
PAGE 30
EIA-422 Pinouts for DB-9, DB-25 and RJ-45 Connectors Signal Description DB-9 Pin DB-25 Pin RJ-45 10 Pin TxD+ Transmitted Data (+) 3 2 5 TxD- Transmitted Data (-) 9 14 1 RxD+ Received Data (+) 2 3 6 RxD- Received Data (-) 6 16 2 RTS+ Request To Send (+) 7 4 3 RTS- Request To Send (-) 4 19 9 CTS+ Clear To Send (+) 8 5 8 CTS- Clear To Send (-) 1 13 10 GND Chassis Ground Shell Shell 4 SG Signal Ground 5 - 7 EIA-422 Software Handshaking (XON/XOFF) Cable Use
PAGE 31
EIA-422 Hardware Handshaking (Ready/Busy) Cable Use the following table as a guide for EIA-422 wiring. Pin numbers have been omitted because they vary from product to product. For Digi pin numbers, see the section titled "Digi EIA-422 Connector Wiring" on page 29. For peripheral device pin numbers, see the documentation for your peripheral device.
PAGE 32
Chapter 7 EIA-422 Asynchronous Interface
PAGE 33
Chapter 6 EIA-485 Asynchronous Interface General EIA-485 Cable Information This section applies to Digi products equipped with EIA-485 asynchronous interfaces. Physical Cable Characteristics EIA-485 interface cables should be shielded twisted-pair cables with a maximum of 4000 feet in length. Each signal requires two leads (one twisted pair of wires) to complete a balanced voltage digital circuit. The shield should be connected to the Chassis Ground of the devices at both ends of the interface cable.
PAGE 34
Digi EIA-485 Connector Wiring Two wires (one twisted pair) are required for each signal, a positive lead ("+"), and a negative lead ("-"). The "+" leads at one end of the cable must be connected to the "+" leads at the other end, and the "-" leads at one end must be connected to the "-" leads at the other end. Incorrect wiring could result in damage to the connected devices. The following tables show the pin configurations for the EIA-485 versions of Digi DB-9 and RJ-45 10 pin connectors.
PAGE 35
RJ-45 8 Pin EIA-485 Multi-drop Mode Digi EIA-485 Connector Wiring Use the table below to see the pin assignments for the RJ-45 connector for EIA-485 multi-drop mode. EtherLite 2 EIA-485 ports are wired for half duplex multiple-drop EIA-485 mode and have no termination installed.
PAGE 36
Chapter 8 EIA-485 Asynchronous Interface
PAGE 37
DataFire 2000 Sync Adapter Chapter 7 Introduction The DataFire SYNC 2000 adapter is an intelligent, high performance synchronous communications adapter that is available in versions for PCI bus and Compact PCI (cPCI) bus compatible systems. The basic design comes with a Motorola MPC860 PowerQUICCô (Quad Integrated Communications Controller), with an integrated PowerPCô RISC processor providing four SCCs on the four-port adapter and two SCCs on the two-port adapter.
PAGE 38
Recommendations Digi recommends shielded cables (15 pF or less capacitance per foot) for all installations. The FCC requires the use of shielded cables to comply with EMI/RFI emission limits. In addition, cables that run long distances or through electrically noisy areas are subject to voltage surges that can cause data errors or equipment damage. EIA-232 specifies a maximum cable length of 50 feet. If you run cables farther than 50 feet, you increase the risk of surge damage and data loss.
PAGE 39
V.35 Pinouts V.35, Male 34-pin Connector Pin CCITT Description A n/a CGND B n/a GND C 105 RTS D 106 CTS E 107 DSR F 109 DCD H 108 DTR P 103A TxD- S 103B TxD+ R 104A RxD- T 104B RxD+ V 115A RxCLKi- X 115B RxCLKi+ Y 114A TxCLKi- AA 114B TxCLKi+ U 113A TxCLKo- W 113B TxCLKo+ EIA-232/V.28 Pinouts EIA-232 / V.28 (V.
PAGE 40
EIA-530/422 Pinouts EIA-530/422, Male DB-25 Connector 40 Pin CCITT Desc.
PAGE 41
Pinout Reference Chapter 8 Async Cable Part Numbers DTE Digi Part Number Description DTE Cable ID Number DCE Digi Part Number Digi Quad Cable DB-9M 76000003 60000211 N/A DB-9F 76000001 -- N/A DB-25M 76000008 - 76000007 DB-25F 76000006 -- 76000005 DB-25M 760000030 -- 760000028 DB-25F 760000026 -- 760000024 DB-9M 76002042 -- N/A DB-9F 76000013 -- N/A Digi Quad Box Digi Octa Cable DB-25M 76000021 60000183 76000020 DB-25F 76000019 -- 76000018 DB-25M 76000031 --
PAGE 42
Digi Order Number Description • ClassicBoard ISA ClassicBoard 16 (16654) Cable • Cable ID Number -- 62080060 PC/16 Ribbon Cable 10000358 10000359 -- PC/4 or PC/8 (2 Boards) Daisy Chain Cable -- 60000186 PC/4 or PC/8 (3 Boards) Daisy Chain Cable -- 60000196 PC/4 or PC/8 (4 Boards) Daisy Chain Cable -- 60000197 PC/16 (2 Boards) Daisy Chain Cable -- 60000268 PC/16e (RJ-45) 10000475 10000476 -- PC/16e and PC/16i (DB-25) 10000390 10000414 -- 16” Cable (DB-44) -- 62080016 60” Cable
PAGE 43
Cross Reference Cable to Order Numbers and ID Numbers Device Click on Description to See Pinout EtherLite RJ-45 to DB-25M Modem Adapter EtherLite RJ-45 to DB-25M 4-Wire Cable (RS-422) EtherLite RJ-45 to DB-25M Console Adapter EtherLite RJ-45 to DB-9F Console Adapter EtherLite and SCSI Terminal Server RJ-45 to DB-9M Modem Cable EtherLite Cables EtherLite and SCSI Terminal Server RJ-45 to DB-9F Terminal Emulator Cable EtherLite and SCSI Terminal Server RJ-45 to DB-25M Modem Cable EtherLite RJ-45 to DB-25M
PAGE 44
Device Click on Description to See Pinout Digi One, PortServer TS, and Multi-Port Serial Cards RJ-45 to DB-9F Cable Adapter Digi One, PortServer TS, and Multi-Port Serial Cards RJ-45 to DB-9F Modem Adapter and Straight-through Cable Digi One, PortServer TS, and Multi-Port Serial Cards RJ-45 to DB-9M Modem Adapter and Crossover Cable Digi One, PortServer TS, and Multi-Port Serial Card Adapters Digi One, PortServer TS, and Multi-Port Serial Cards RJ-45 to DB-25M Printer Adapter and Cable Digi One, PortS
PAGE 45
Device Click on Description to See Pinout Digi One EM DB-9 Connector Pinouts Digi One EM Digi One IA RealPort Cable ID Part Number *To order Digi Cable or Adapter *Labled on Cable or Adapter 63000058-01 63000066-01 63000070-01 Digi One EM DB-9 and Terminal Block Pinout Digi One IA RealPort DB-9 Connector Pinout 63000084-01 Digi One SP Digi One SP DB-9 Pinout 63000058-01 63000066-01 63000070-01 DataFire Sync 2000 X.21 V.
PAGE 46
Device Modem Cables Terminal Emulator Cable Click on Description to See Pinout DB-9F to DB-9M Modem Cable DB-9F to DB-25M Modem Cable DB-25F to DB-9M Modem Cable DB-25F to DB-25M Modem Cable SCSI Terminal Server DB-25M to DB-9M Modem Cable RJ-45 (Altpin On) to DB-9M Modem Cable RJ-45 (Altpin On) to DB-25M Modem Cable RJ-45 10 Pin to DB-9M Modem Cable RJ-45 10 Pin to DB-25M Modem Cable Part Number *To order Digi Cable or Adapter Cable ID *Labled on Cable or Adapter 76000239 76000129 61090048 61020024
PAGE 47
Device Terminal Printer Cable SCSI Terminal Server Cable and Adapters Click on Description to See Pinout DB-9F to DB-9M Terminal Printer Cable DB-9F to DB-25M Terminal Printer Cable DB-25F to DB-9M Terminal Printer Cable SCSI Terminal Server DB-25M to DB-9M Terminal Printer Cable SCSI Terminal Server DB-25M to DB-25M Terminal Printer Cable RJ-11 6 Pin/4-Wire to DB-9M Terminal Printer Cable RJ-11 6 Pin/4-Wire to DB-25M Terminal Printer Cable RJ-11 6 Pin to DB-9F Terminal Printer Cable RJ-11 6 Pin to DB-25
PAGE 48
EIA 232 Information RS 232 Flow Control Primer RS RS-232 Flow Control Primer Hardware flow control uses pins RTS and CTS to gate flow back and forth between two connected serial devices. The DTE device uses RTS to start and stop flow from the DCE device, and the DCE device uses CTS to gate flow from the DTE device. This method is popular for higher speed connections where flow control reaction time is more critical.
PAGE 49
Fiber Optic Fiber Optic Cable Specifications and Source CSP Fiber Optic Cable Specifications and Source CSP, Inc. can provide you with reliable fiber assemblies certified to function properly with DigiBoard equipment. Fiber is the best solution for transmitting large amounts of data over long distances at high speeds without interference or lost data caused by outside factors such as weather, radio frequency signals or other electrical noise.
PAGE 50
Operating Load 450N 450N Installation Load 700N 700N Operating Bend Radius 25 mm 25 mm Installation Bend Radius 4 mm 4 mm Impact Resistance 20 impacts w/1.0N-m(EIA-425-25) Crush Resistance 500 N/cm 500 N/cm Flexing 5000 5000 Operating Temperature -40 C to 85 C -40 C to 85 C Storage Temperature -55 C to 85 C -55 C to 85 C Flame Retard UL-1666 OFNR UL-910 OFNP Connector Type ST Ferrule Material Stainless Steel Termination Break Strength 30 lbs. Connection Loss 0.
PAGE 51
Loopback Connector Pinouts DB-15M, DB-25F, DB-25F, DB-15F, DB-25F, RJ-45 Loopback Connectors Loopback connectors must have the following sets of pins tied together: DB-15 EIA-232 Male DB-25 EIA-232 Female DB-25 V.35 Female DB-15 X.
PAGE 52
For use with Etherlite 2, 80, 160, 162, 32 – All Models Etherlite, RJ-45 to DB-25 Modem Adapter DSR DCD RxD TxD SG DTR CTS 2 3 4 5 6 7 8 Direction CTS DTR SG TxD RxD DCD DSR RTS Signal 5 20 7 2 3 8 6 4 To DB-25 All RJ45 cable adapters are 8-pin. This adapter utilizes the CTS signal of the modem for hardware flow control (RTS / CTS).
PAGE 53
EtherLite RJ-45 to DB-25M 4-Wire Cable (RS-422) EtherLite RS422 RJ45-DB25 pinouts The wiring diagram for a RJ45 to DB25 4-wire full duplex cable is shown in Table 1.
PAGE 54
For use with EtherLite 2, 80, 160, 162, 32 – All Models EtherLite, RJ-45 to DB-25 Console Adapter DCD RxD TxD SG DTR CTS 3 4 5 6 7 8 Direction 4 8 DCD RTS 6 7 3 2 20 5 To DB-25 DSR SG RxD TxD DTR CTS Signal Pin 1 90000604_A EtherLite DB25M Console Adapter (single-pack) All RJ45 cable adapters are 8-pin. This adapter utilizes the RTS signal of the serial device for hardware flow control (RTS/CTS).
PAGE 55
For use with EtherLite 2, 80, 160, 162, 32 – All Models EtherLite, RJ-45 to DB-9 Console Adapter DCD RxD TxD SG DTR CTS 3 4 5 6 7 8 Direction 7 6 DSR RTS 1 5 2 3 4 8 To DB-9 DCD SG RxD TxD DTR CTS Signal 90000605_A EtherLite DB9F Console Adapter (single-pack) All RJ45 cable adapters are 8-pin. This cable utilizes the RTS signal of the serial device for hardware flow control (RTS / CTS).
PAGE 56
EtherLite and SCSI Terminal Server RJ-45 to DB-9M Modem Cable Modem Cables RJ-45 (Central Data) to DB-9 EIA-232 Boards with RJ-45 (Central Data) Cable Connectors- EtherLite 2, EtherLite 8, EtherLite 16, EtherLite 160, EtherLite 32, SCSI Terminal Server 1400, SCSI Terminal Server 1800, SCSI Terminal Server 1610, SCSI Terminal Server 1032. The wiring diagram for an RJ-45 8-pin to DB-9 modem cable is shown in Table 1.
PAGE 57
EtherLite and SCSI Terminal Server RJ-45 to DB-9F Terminal Emulator Cable Cables PC Terminal Emulator Cables, RJ-45 (Central Data) to DB-9 EIA-232 Boards with RJ-45 (Central Data) Cable Connectors - EtherLite 2, EtherLite 8, EtherLite 16, EtherLite 160, EtherLite 32, SCSI Terminal Server 1400, SCSI Terminal Server 1800, SCSI Terminal Server 1610, SCSI Terminal Server 1032. The wiring diagram for an RJ-45 8-pin to DB-9 PC terminal emulator cable is shown in Table 1.
PAGE 58
EtherLite and SCSI Terminal Server RJ-45 to DB-25M Modem Cable Modem Cables RJ-45 (Central Data) to DB-25 EIA-232 Boards with RJ-45 (Central Data) Cable Connectors- EtherLite 2, EtherLite 8, EtherLite 16, EtherLite 160, EtherLite 32, SCSI Terminal Server 1400, SCSI Terminal Server 1800, SCSI Terminal Server 1610, SCSI Terminal Server 1032. The wiring diagram for an RJ-45 8-pin to DB-25 modem cable is shown in Table 1.
PAGE 59
EtherLite RJ-45 to DB-25M DTE Modtap Adapter Modtap - RJ-45f (Etherlite) to DB-25m DTE The wiring diagram for an RJ-45 8-pin to DB-25 DTE modtap is shown in Table 1. This adapter is used to connect a modem to an Etherlite port, and is available from Digi by ordering part number 76000450.
PAGE 60
EtherLite RJ-45 to DB-25M DCE Modtap Adapter Modtap - RJ-45f (EtherLite) to DB-25m DCE The wiring diagram for an RJ-45 8-pin to DB-25 DCE modtap is shown in Table 1. This adapter is used to connect a terminal/printer to an EtherLite port, and is available from Digi by ordering part number 76000451.
PAGE 61
EtherLite RJ-45 to DB-9F DCE Modtap Adapter Modtap - RJ -45f (Ether L ite) to DB -9f DCE The wiring diagram for an RJ-45 8-pin to DB-9 DCE modtap is shown in Table 1. This adapter is used to connect a console/com port to an EtherLite port, and is available from Digi by ordering part number 76000461.
PAGE 62
EtherLite and SCSI Terminal Server RJ-45 to RJ-45 Cisco Console Adapter Adapter Cables Digi - Cisco Console Adapter, RJ-45 (Central Data) to RJ-45 EIA-232 Boards with RJ-45 Cable Connectors - EtherLite 2, EtherLite 8, EtherLite 16, EtherLite 160, EtherLite 32, SCSI Terminal Server 1400, SCSI Terminal Server 1800, SCSI Terminal Server 1610, SCSI Terminal Server 1032. The wiring diagram for a RJ-45 8-pin to Cisco Console RJ-45 8-pin adapter cable is shown in Table 1.
PAGE 63
EtherLite and SCSI Terminal Server RJ-45 to DB-25M Terminal Printer Cable Terminal/Printer Cables, RJ-45 (Central Data) to DB-25 EIA-232 Boards with RJ-45 (Central Data) Cable Connectors - EtherLite 2, EtherLite 8, EtherLite 16, EtherLite 160, EtherLite 32, SCSI Terminal Server 1400, SCSI Terminal Server 1800, SCSI Terminal Server 1610, SCSI Terminal Server 1032. The wiring diagram for an RJ-45 8-pin to DB-25 terminal/printer cable is shown in Table 1.
PAGE 64
For use with Digi One TS, Portserver TS 2/4/8/16, and Multi-Port Serial Cards with RJ45 connectors Digi TS, RJ-45 to DB-9 Console Adapter RTS Ground TxD RxD SG CTS DTR 2 3 4 5 6 7 8 Direction 1 6 DSR 7 5 3 2 Shell 8 4 To DB-9 DCD RTS SG TxD RxD Ground CTS DTR Signal Pin 1 Female DB-9 90000606_A Digi TS DB9F Console Adapter (4-pack) All RJ45 cable adapters are 8-pin. Altpin should be turned on when using this cable adapter so that DTR will drive DCD (standard usage).
PAGE 65
RTS Ground TxD RxD SG CTS DTR 2 3 4 5 6 7 8 Direction 6 8 DCD 4 7 2 3 Shell 5 20 To DB-25 DSR RTS SG TxD RxD Ground CTS DTR Signal Pin 1 Male DB-25 76000698 90000607_A Digi TS DB25M Console Adapter (4-pack) All RJ45 cable adapters are 8-pin. Altpin should be turned on when using this cable adapter so that DTR will drive DCD (standard usage). If altpin is turned off, the hardware signal on RJ45 pin 1 becomes DSR instead of DCD.
PAGE 66
For use with Digi One TS, Portserver TS 2/4/8/16, and Multi-Port Serial Cards with RJ45 connectors Digi TS, RJ-45 to DB-25 Console Adapter RTS Ground TxD RxD SG CTS DTR 2 3 4 5 6 7 8 Direction 6 8 DCD 4 7 2 3 Shell 5 20 To DB25 DSR RTS SG TxD RxD Ground CTS DTR Signal Female DB-25 Pin 1 90000608_A Digi TS DB25F Console Adapter (4-pack) All RJ45 cable adapters are 8-pin. Altpin should be turned on when using this cable adapter so that DTR will drive DCD (standard usage).
PAGE 67
For use with Digi One TS, Portserver TS 2/4/8/16, and Multi-Port Serial Cards with RJ45 connectors Digi TS, RJ-45 to DB-25 Modem Adapter RTS Ground TxD RxD SG CTS DTR 2 3 4 5 6 7 8 DTR CTS SG RxD TxD Ground RTS DCD Signal 20 5 7 3 2 Shell 4 8 To DB-25 Pin 1 Male DB-25 Cable Adapter not to scale Female RJ-45 8-pin Pin 1 90000609_A Digi TS DB25M Modem Adapter (4-pack) All RJ45 cable adapters are 8-pin.
PAGE 68
dap For use with Digi One TS, Portserver TS 2/4/8/16, and Multi-Port Serial Cards with RJ45 connectors Digi TS, RJ-45 to DB-9 Modem Adapter RTS Ground TxD RxD SG CTS DTR 2 3 4 5 6 7 8 DTR CTS SG RxD TxD Ground 4 8 5 2 3 Shell 7 6 DSR RTS 1 To DB-9 DCD Signal Pin 1 Male DB-9 Cable Adapter not to scale Female RJ-45 8-pin Pin 1 90000610_A Digi TS DB9M Modem Adapter (4-pack) All RJ45 cable adapters are 8-pin.
PAGE 69
For use with Digi One TS, Portserver TS 2/4/8/16, and Multi-Port Serial Cards with RJ45 connectors Digi TS, RJ-45 to DB-25 Printer Adapter RTS Ground TxD RxD SG CTS DTR 2 3 4 5 6 7 8 Direction 6 8 DCD 20 7 2 3 Shell 5 4 To DB25 DSR DTR SG TxD RxD Ground CTS RTS Signal Pin 1 Male DB-25 90000611_A Digi TS DB25M Printer Adapter (4-pack) All RJ45 cable adapters are 8-pin. For use with Printers.
PAGE 70
Digi CM RJ-45 to DB-9F DTE RS-232 Crossover Cable RJ45 to DB9 Female Crossover Cable This cable will allow you to connect from the CM32 serial ports to console ports, terminals, printers and any other DTE RS232 device. The wiring diagram is shown in Table 1.
PAGE 71
For use with Digi CM 8, 16, 32, 48 – All Models Digi CM, RJ-45 to DB-25 Modem Adapter DSR RxD Ground DCD TxD DTR RTS 2 3 4 5 6 7 8 Direction RTS DTR TxD DCD Ground RxD DSR CTS Signal 4 20 2 8 7 3 6 5 To DB-25 90000612_A Digi CM DB25M Modem Adapter (8-pack) All RJ45 cable adapters are 8-pin.
PAGE 72
For use with Digi CM 8, 16, 32, 48 – All Models Digi CM, RJ-45 to DB-9 Console Adapter DSR DCD RxD Ground TxD RTS DTR 2 5 3 4 6 8 7 1 6 DSR 8 2 5 DCD CTS RxD SG 3 4 DTR TxD 7 To DB-9 RTS Signal Pin 1 Female DB-9 Cable Adapter not to scale Female RJ-45 8-pin Pin 1 90000613_A Digi CM DB9F Console Adapter (8-pack) All RJ45 cable adapters are 8-pin.
PAGE 73
For use with Digi CM 8, 16, 32, 48 – All Models Digi CM, RJ-45 to DB-25 Console Adapter DSR DCD RxD Ground TxD RTS DTR 2 5 3 4 6 8 7 76000672 All RJ45 cable adapters are 8-pin.
PAGE 74
For use with Digi CM 8, 16, 32, 48 – All Models Digi CM, RJ-45 to DB-25 Console Adapter DSR DCD RxD Ground TxD RTS DTR 2 5 3 4 6 8 7 76000673 All RJ45 cable adapters are 8-pin.
PAGE 75
For use with Digi CM 8, 16, 32, 48 – All Models Digi CM, RJ-45 to DB-9 Modem Adapter DSR RxD Ground DCD TxD DTR RTS 2 3 4 5 6 7 8 Direction RTS DTR TxD DCD SG RxD DSR CTS Signal 7 4 3 1 5 2 6 8 To DB-9 90000616_A Digi CM DB9M Modem Adapter (8-pack) All RJ45 cable adapters are 8-pin.
PAGE 76
Digi CM RJ-45 to DB-25M (DCE RS 232) Straight-Through Cable RJ45 to DB25 Male Straight Through Cable This cable will allow you to connect from the CM32 serial ports to modems and other DCE RS232 devices. The wiring diagram is shown in Table 1.
PAGE 77
Digi CM RJ-45 to DB-25M (DTE RS 232) Crossover Cable RJ45 to DB25 Female/Male Crossover Cable This cable will allow you to connect from the CM32 serial ports to console ports, terminals, printers and any other DTE RS232 device. The wiring diagram is shown in Table 1.
PAGE 78
Digi CM RJ-45 to RJ-45 Sun Netra or Cisco Crossover Cable RJ45 to Sun Netra/Cisco RJ45 Crossover Cable This cable will allow you to connect to a Sun Netra server or a Cisco product. The wiring diagram is shown in Table 1.
PAGE 79
Digi CM RJ-45 to Sun Mini Din Cable Digi CM RJ45 to Sun Mini Din 8-Pin The Digi CM uses an RJ45 connector for serial ports. The pin assignment of the RJ45 connector for serial ports is summarized in table 2 below. Each pin has a function according to the serial communication type configuration. The Sun Mini Din 8-Pin wiring diagram is shown in Table 1.
PAGE 81
Async Conversion RJ-XX to DB-XX IEA 232 Conversion Chart: Acceleport, Etherlite, and PortServer Families Acceleport, Etherlite, and PortServer Families RJXX to DBXX Conversion Sheet RJ- 11 RJ-11 RJ-45 4-pin 6-pin 8-pin RJ-45 EtherLite Signal 10-pin 8-pin Name DB-25 (Male) DB-9 (Male) 1------------ RI -----------------------22 ---------9 1------------- 2------------ 2-------------- DSR ------------------------6 ---------6 1---------2------------- 3------------ 1--------------- RTS -----------
PAGE 82
Cable Vendors Recommended Custom Cable Vendors Below are our recommended cable vendors to make or extend the length of cables The Whyte haus 260-484-5666 the.whytehaus@verizon.net DataCable Technologies 630-226-5600 r.j@datacabletech.com Contact: RJ Clabots Predator Grizzly Cable 503-292-7151 x1101 Black Box 800-231-3222 Control Cable Inc. 800-296-4411 sales@controlcable.
PAGE 83
DataFire Sync 2000 SCSI Pinouts DataFire SYNC 2000 Cables DataFire SYNC 2000 SCSI Connector Pinout SIGNAL SCSI J1 SCSI J2 NOTES ID0 1 -- OPEN ID1 35 -- OPEN ID2 2 -- OPEN ID3 36 -- TIED TO SHELL ON 68 PIN END GND SHELL SHELL,A,B USE BRAID TO CONNECT SHELLS 103B TxD+ 4 S TWISTED PAIR 103A TxD- 38 P 113B TxCLKo+ 5 W 113A TxCLKo- 39 U 105B RTS+ 6 105A RTS- 40 108B DTR+ 7 108A DTR - 41 104B RxD+ 8 T 104A TxD- 42 R 115B RxCLKi+ 43 X 115A RxCLKi- 9 V 114B
PAGE 84
Digi One EM DB-9 Connector Pinouts DB Digi One EM The wiring diagram for the DB-9 connector is shown in Table 1.
PAGE 85
Digi One IA RealPort DB-9 Connector Pinout DIGI ONE REALPORT IA EIA-232 PINOUTS The wiring diagram for the EIA-232 DB-9 connector is shown in Table 1 and the Terminal Block in Table 2.
PAGE 86
Digi One EM DB-9 and Terminal Block Pinout The wiring diagram for the EIA-232 DB-9 connector is shown in Table 1 and the Terminal Block in Table 2.
PAGE 87
Digi One SP DB-9 Pinout DIGI ONE SINGLE PORT PINOUT The wiring diagram for the DB-9 connector is shown in Table 1.
PAGE 88
Async EIA-422 DB-9 Connector Pinout DB 9 EIA422 Pinouts DB-9 Pinout Asynchronous EIA-422 The wiring diagram for an EIA-422 DB-9 connector is shown in Table 1.
PAGE 89
Async EIA-422 DB-25 Pinout DB DB-25 Pinout, Asynchronous EIA-422 EIA-422 Boards with DB-25 cable conncectors The wiring diagram for an EIA-422 DB-25 connector is shown in Table 1.
PAGE 90
Async RJ-45 to RJ-45 Crossover Cable Digi RJ45 8-pin to Digi RJ45 8-pin Crossover Digi RJ-45 8-pin to Digi RJ-45 8-pin Crossover Cable For Cross-Connecting Digi Asynchronous Ports Together Table 1: Digi RJ-45 8-pin to Digi RJ-45 8-pin Crossover Cable From RJ-45 Signal Direction Signal To RJ-45 Digi Digi 1 DSR DTR 8 5 RxD TxD 4 4 TxD RxD 5 8 DTR DSR 1 6 SG SG 6 2 RTS CTS 7 7 CTS RTS 2 ● Arrows indicate which direction the signal is flowing
PAGE 91
DB-25F to RJ-45 Cisco Console Cable Adapter Adapter Cables Digi EIA-232 - Cisco Console Adapter, DB-25 to RJ-45 The wiring diagram for a DB-25 to Cisco Console RJ-45 8-pin adapter cable is shown in Table 1.
PAGE 92
SCSI Terminal Server DB-25M to RJ-45 Cisco Console Cable Adapter Modem Cables Digi - Cisco Console Adapter, DB-25 to RJ-45 EIA-232 Boards which require DB-25 Male Cables Assemblies - SCSI Terminal Server ST1002, SCSI Terminal Server ST1008, SCSI Terminal Server ST1016, SCSI Terminal Server ST1600 The wiring diagram for a DB-25 to Cisco Console RJ-45 8-pin adapter cable is shown in Table 1.
PAGE 93
Difference Between DTE and DCE DTE vs. DCE This is one of the most misunderstood areas of RS-232. DTE stands for Data Terminal Equipment, and DCE stands for Data Communications Equipment. DTE is typically either a dumb terminal or the serial port on a computer/workstation. DCE is typically a modem, DSU/CSU, or other piece of data communications equipment, hence the names. This is all most people really need to know about these terms.
PAGE 94
DB-9F to RJ-45 3 COM Total Control/COMPAQ Microcom Modem Cable Modem Cables EIA-232 Modem Cables, DB-9 to RJ-45 8-pin The wiring diagram for a DB-9 pin to 3COM Total Control RJ-45 8-pin/Compaq Microcom RJ-45 8-pin modem cable is shown in Table 1.
PAGE 95
SCSI Terminal Server DB-25M to RJ-45 3 COM Total Control/COMPAQ Microcom Modem Cable Modem Cables Modem Cables, DB-25 to RJ-45 EIA-232 Boards which require DB-25 Male Cables Assemblies - SCSI Terminal Server ST1002, SCSI Terminal Server ST1008, SCSI Terminal Server ST1016, SCSI Terminal Server ST1600 The wiring diagram for a DB-25 pin to 3COM Total Control/COMPAQ Microcom rj-45 8-pin modem cable is shown in Table 1.
PAGE 96
DB-25F to RJ-45 3 COM Total Control/COMPAQ Microcom Modem Cable Modem Cables EIA-232 Modem Cables, DB-25 to RJ-45 The wiring diagram for a DB-25 pin to 3COM Total Control/COMPAQ Microcom RJ-45 8-pin modem cable is shown in Table 1.
PAGE 97
RJ-45 to RJ-45 (Altpin On) 3 COM Total Control/COMPAQ Microcom Modem Cable Modem Cables EIA-232 Modem Cables, RJ-45 to RJ-45 The wiring diagram for a RJ-45 8-pin to 3COM Total Control/Compaq Microcom RJ-45 8-pin modem cable is shown in Table 1.
PAGE 98
RJ-45 10 Pin to RJ-45 3 COM Total Control/Compaq Microcom Modem Cable Modem Cables EIA-232 Modem Cables, RJ-45 to RJ-45 8-pin The wiring diagram for a RJ-45 10-pin to 3COM Total Control/Compaq Microcom RJ-45 8-pin pin modem cable is shown in Table 1.
PAGE 99
DB-9F to DB-9M Modem Cable Modem Cables EIA-232 Modem Cables DB-9 to DB-9 The wiring diagram for a DB-9 to DB-9 modem cable is shown in Table 1. Table 1: EIA-232 DB-9 to DB-9 modem cable DB-9 Signal Direction Signal To DB-9 1 DCD DCD 1 2 RxD RxD 2 3 TxD TxD 3 4 DTR DTR 4 5 SG SG 5 6 DSR DSR 6 7 RTS RTS 7 8 CTS CTS 8 9 RI RI 9 Shell GND GND Shell * Arrows indicate which direction the signal is flowing NOTES: ● Altpin should be turned off when using this cable.
PAGE 100
DB-9F to DB-25M Modem Cable Modem Cables EIA-232 Modem Cables DB-9 to DB-25 The wiring diagram for a DB-9 to DB-25 modem cable is shown in Table 1.
PAGE 101
DB-25F to DB-9M Modem Cable Modem Cables EIA-232 Modem Cables DB-25 to DB-9 The wiring diagram for a DB-25 to DB-9 modem cable is shown in Table 1.
PAGE 102
DB-25F to DB-25M Modem Cable Modem Cables EIA-232 Modem Cables DB-25 to DB-25 The wiring diagram for a DB-25 to DB-25 modem cable is shown in Table 1.
PAGE 103
SCSI Terminal Server DB-25M to DB-9M Modem Cable Modem Cables Modem Cables DB-25 to DB-9 EIA-232 Boards which require DB-25 Male Cables Connectors- SCSI Terminal Server ST1002, SCSI Terminal Server ST1008, SCSI Terminal Server ST1016, SCSI Terminal Server ST1600 The wiring diagram for a DB-25 to DB-9 modem cable is shown in Table 1.
PAGE 104
RJ-45 (Altpin On) to DB-9M Modem Cable Modem Cables EIA-232 Modem Cables Altpin RJ-45 8-pin to DB-9 The wiring diagram for an altpin RJ-45 8-pin to DB-9 modem cable is shown in Table 1.
PAGE 105
RJ-45 (Altpin On) to DB-25M Modem Cable Modem Cables EIA-232 Modem Cables, Altpin RJ-45 8-pin to DB-25 The wiring diagram for a Altpin RJ-45 8-pin to DB-25 modem cable is shown in Table 1.
PAGE 106
RJ-45 10 Pin to DB-9M Modem Cable Modem Cables EIA-232 Modem Cables RJ-45 10-pin to DB-9 The wiring diagram for an RJ-45 10-pin to DB-9 modem cable is shown in Table 1.
PAGE 107
RJ-45 10 Pin to DB-25M Modem Cable Modem Cables EIA-232 Modem Cables RJ-45 10-pin to DB-25 The wiring diagram for a RJ-45 10-pin to DB-25 pin modem cable is shown in Table 1.
PAGE 108
DB-9F to DB-9F Terminal Emulator Cable Cables EIA-232 PC Terminal Emulator Cables, DB-9 to DB-9 The wiring diagram for a DB-9 to DB-9 PC terminal emulator cable is shown in Table 1.
PAGE 109
DB-9F to DB-25F Terminal Emulator Cable Cables EIA-232 PC Terminal Emulator Cables, DB-9 to DB-25 The wiring diagram for a DB-9 to DB-25 PC terminal emulator cable is shown in Table 1.
PAGE 110
DB-25F to DB-9F Terminal Emulator Cable Cables EIA-232 PC Terminal Emulator Cables, DB-25 to DB-9 The wiring diagram for a DB-25 to DB-9 PC terminal emulator cable is shown in Table 1.
PAGE 111
DB-25F to DB-25F Terminal Emulator Cable Cables EIA-232 PC Terminal Emulator Cables, DB-25 to DB-25 > The wiring diagram for a DB-25 to DB-25 PC Terminal Emulator cable is shown in Table 1.
PAGE 112
SCSI Terminal Server DB-25M to DB-9F Terminal Emulator Cable Cables PC Terminal Emulator Cables, DB-25 to DB-9 EIA-232 Boards which require DB-25 Male Cables Connectors - SCSI Terminal Server ST1002, SCSI Terminal Server ST1008, SCSI Terminal Server ST1016, SCSI Terminal Server ST1600 The wiring diagram for a DB-25 to DB-9 PC terminal emulator cable is shown in Table 1.
PAGE 113
SCSI Terminal Server DB-25M to DB-25F Terminal Emulator Cable Cables PC Terminal Emulator Cables, DB-25 to DB-25 EIA-232 Boards which require DB-25 Male Cables Connectors- SCSI Terminal Server ST1002, SCSI Terminal Server ST1008, SCSI Terminal Server ST1016, SCSI Terminal Server ST1600 The wiring diagram for a DB-25 to DB-25 PC Terminal Emulator cable is shown in Table 1.
PAGE 114
RJ-11 6 Pin/4-Wire to DB-9F Terminal Emulator Cable Cables EIA-232 PC Terminal Emulator Cables, RJ-11 6-pin/4-wire to DB-9 The wiring diagram for an RJ-11 6-pin/4-wire to DB-9 PC terminal emulator cable is shown in Table 1.
PAGE 115
RJ-11 6 Pin/4-Wire to DB-25F Terminal Emulator Cable Software Flow Control Only Cables EIA-232 PC Terminal Emulator Cables, RJ-11 6-pin/4-wire to DB-25 Software Flow Control Only The wiring diagram for an RJ-11 6-pin/4-wire to DB-25 PC terminal emulator cable is shown in Table 1.
PAGE 116
RJ-11 6 Pin to DB-9F Terminal Emulator Cable Cables EIA-232 PC Terminal Emulator Cables, RJ-11 6-pin to DB-9 The wiring diagram for an RJ-11 6-pin to DB-9 PC terminal emulator cable is shown in Table 1.
PAGE 117
RJ-11 6 Pin to DB-25F Terminal Emulator Cable Cables EIA-232 PC Terminal Emulator Cables, RJ-11 6-pin to DB-25 The wiring diagram for an RJ-11 6-pin to DB-25 PC terminal emulator cable is shown in Table 1.
PAGE 118
RJ-45 4-Wire to DB-9F Terminal Emulator Cable Software Flow Control Only Cables EIA-232 PC Terminal Emulator Cables, RJ-45 8-pin/4-wire to DB-9 Software Flow Control Only The wiring diagram for an RJ-45 8-pin to DB-9 PC terminal emulator cable using only 4 wires is shown in Table 1.
PAGE 119
RJ-45 4-Wire to DB-25F Terminal Emulator Cable Software Flow Control Only Cables EIA-232 PC Terminal Emulator Cables, RJ-45 8-pin/4-wire to DB-25 Software Flow Control Only The wiring diagram for an RJ-45 8-pin to DB-25 PC terminal emulator cable using only 4 wires is shown in Table 1.
PAGE 120
RJ-45 (Altpin On) to DB-9F Terminal Emulator Cable Cables PC Terminal Emulator Cables, Altpin RJ-45 8-pin to DB-9 The wiring diagram for an altpin RJ-45 8-pin to DB-9 PC terminal emulator cable is shown in Table 1.
PAGE 121
RJ-45 (Altpin On) to DB-25F Terminal Emulator Cable Cables EIA-232 PC Terminal Emulator Cables, Altpin RJ-45 8-pin to DB-25 The wiring diagram for an altpin RJ-45 8-pin to DB-25 PC terminal emulator cable is shown in Table 1.
PAGE 122
RJ-45 to DB-9F Terminal Emulator Cable PC Terminal Emulator Cables, RJ-45 8-pin to DB-9 The wiring diagram for an RJ-45 8-pin to DB-9 PC terminal emulator cable is shown in Table 1.
PAGE 123
RJ-45 10 Pin to DB-9F Terminal Emulator Cable Cables EIA-232 PC Terminal Emulator Cables, RJ-45 10-pin to DB-9 The wiring diagram for an RJ-45 10-pin to DB-9 PC terminal emulator cable is shown in Table 1.
PAGE 124
RJ-45 10 Pin to DB-25F Terminal Emulator Cable Cables EIA-232 PC Terminal Emulator Cables, RJ-45 10-pin to DB25 The wiring diagram for an RJ-45 10-pin to DB-25 PC terminal emulator cable is shown in Table 1.
PAGE 125
RJ-45 (Altpin On) to RJ-45 Cisco Console Adapter Adapter Cables Digi - Cisco Console Adapter, Altpin RJ-45 to RJ-45 The wiring diagram for an Altpin RJ-45 8-pin to a Cisco Console RJ-45 8-pin adapter cable is shown in Table 1.
PAGE 126
V.35 to DB-25M Cabling This V.35 cabling option provides a DB25 Male connector. This cable type is capable of handling data rates up to 2.048Mbps (E1) as well as lower speeds (9600, 19200, 56000, etc.).
PAGE 127
V.35 Pinout V.35 Pinout V.35 Boards with Winchestor cable assemblies (see part numbers for cables below) - Sync 570 (EIA-232 only), Sync 570i (X.21/EIA-530), Sync 570i (EIA-232/V.35), Sync 570i UIB (PCI boards),Syncport, Sync 2000. • • • • • Sync 2000 single port V.35 cable Sync 570i UIB single port V.35 cable Sync 570i 2 port V.35 cable Sync 570i 4 port V.35 cable DB-25 to Winchestor convertor for ISA Sync 570i V.
PAGE 128
X.21 V.11 to DB-15 Cable X.21/V.11 Pinout DB25 Direction Signal 1 ↔ CGND 2 TxD+ 3 RxD+ 4 RTS+ 5 CTS+ 6 DCE Ready + 7 ↔ SG 8 Received Line Signal Indicator + 9 RxClk + 10 11 Recieved Lne Signal Indicator TxClk External + 12 TxClk Internal - 13 14 CTSTxD- 15 TxClk Internal + 16 17 RxDRxClk- 19 20 RTSDTE Ready + 22 23 DCE Ready + DTE Ready - 24 TxClk External - Shell NOTES: ↔ GND X.21/V.
PAGE 129
Digi AccelePort Xp and NEO HD-68 Pin Ultra SCSI Connector The connector provides a connection for the RS232 signals on the PCB to a cable to interface various 4, 8 and 16 port peripheral devices. The first table is for ports 1-8 and the second table is for ports 9-16. The pin-outs for the connector and the asynchronous ports configuration is as follows: see Table 1 for: Ports 1-8 of HD-68 Connector for 4 or 8 port boards. see Table 2 for: Ports 9-16 of second HD-68 Connector when using 16 port board.
PAGE 130
Table 1: 68 Pin Ultra SCSI Wire name Male DB-25 Connector 68 Pin Ultra SCSI Wire name Male DB-25 Connector 26 GND P3-7, P1-7 60 GND P4-7, P2-7 27 TxD1 P1-2 61 TxD2 P2-2 28 DSR1 P1-6 62 DSR2 P2-6 29 DTR1 P1-20 63 DTR2 P2-20 30 DCD1 P1-8 64 DCD2 P2-8 31 RTS1 P1-4 65 RTS2 P2-4 32 R11 P1-22 66 R12 P2-22 33 CTS1 P1-5 67 CTS2 P2-5 34 RXD1 P1-3 68 RXD2 P2-3 Table 2: PORTS 9-16 of second HD-68 Connector when using 16 port board 68 Pin Ultra SCSI Wire name
PAGE 131
20 RI11 P11-22 54 RI12 P12-22 21 RTS11 P11-4 55 RTS12 P12-4 22 DCD11 P11-8 56 DCD12 P12-8 23 DTR11 P11-20 57 DTR12 P12-20 24 DSR11 P11-6 58 DSR12 P12-6 25 TxD11 P11-2 59 TxD12 P12-2 26 GND P11-7, P9-7 60 GND P12-7, P10-7 27 TxD9 P9-2 61 TxD10 P10-2 28 DSR9 P9-6 62 DSR10 P10-6 29 DTR9 P9-20 63 DTR10 P10-20 30 DCD9 P9-8 64 DCD10 P10-8 31 RTS9 P9-4 65 RTS10 P10-4 32 RI9 P9-22 66 RI10 P10-22 33 CTS9 P9-5 67 CTS10 P10-5 34 RXD9
PAGE 132
Sync V.24 DB-25 Connector Pinout V.24 (EIA-232) Pinout V.24 (EIA-232) Boards with DB-25 cable assemblies (see part numbers for cables below) Sync 570 (EIA-232 only), Sync 570i (EIA-232/V.35), Sync 570i UIB (PCI boards), Syncport, Sync 2000. • • • • Sync 2000 single port EIA-232 (V.
PAGE 133
EIA 422 DB-25 Pinouts for Sync Boards Sync 570 (EIA-232 only), Sync 570i (EIA-232/V.35), Sync 570i UIB (PCI boards), Syncport, Sync 2000.
PAGE 134
Sync 2000 Single Port V.36/EIA-449 Pinout V.36/EIA-449 Pinout V.36/EIA-449 Boards with DB-37 cable assemblies (see part numbers for cables below) Sync 2000 single port V.
PAGE 135
30 Terminal Ready - 31 Receiver Ready - 32 Select Standby 33 Signal Quality 34 New Signal 35 Terminal Timing - 36 Standby Indicator 37 ↔ Send Common Shell ↔ GND
PAGE 136
DB-9F to DB-9M Terminal Printer Cable Modem Cables Terminal/Printer Cables, DB-9 to DB-9 The wiring diagram for a DB-9 pin to DB-9 pin terminal/printer cable is shown in Table 1.
PAGE 137
DB-9F to DB-25M Terminal Printer Cable Modem Cables Terminal/Printer Cables, DB-9 to DB-25 The wiring diagram for a DB-9 to DB-25 terminal/printer cable is shown in Table 1.
PAGE 138
DB-25F to DB-9M Terminal Printer Cable Modem Cables Terminal/Printer Cables, DB-25 to DB-9 The wiring diagram for a DB-25 to DB-9 terminal/printer cable is shown in Table 1.
PAGE 139
DB-25F to DB-25M Terminal Printer Cable Modem Cables Terminal/Printer Cables, DB-25 to DB-25 The wiring diagram for a DB-25 to DB-25 terminal/printer cable is shown in Table 1.
PAGE 140
SCSI Terminal Server DB-25M to DB-9M Terminal Printer Cable Cables Terminal/Printer Cables, DB-25 to DB-9 EIA-232 Boards which require DB-25 Male Cables Connectors - SCSI Terminal Server ST1002, SCSI Terminal Server ST1008, SCSI Terminal Server ST1016, SCSI Terminal Server ST1600 The wiring diagram for a DB-25 to DB-9 terminal/printer cable is shown in Table 1.
PAGE 141
SCSI Terminal Server DB-25M to DB-25M Terminal Printer Cable Modem Cables Terminal/Printer Cables, DB-25 to DB-25 EIA-232 Boards which require DB-25 Male Cables Assemblies (see part numbers below) - SCSI Terminal Server ST1002, SCSI Terminal Server ST1008, SCSI Terminal Server ST1016, SCSI Terminal Server ST1600 The wiring diagram for a DB-25 to DB-25 terminal/printer cable is shown in Table 1.
PAGE 142
RJ-11 6 Pin/4-Wire to DB-9M Terminal Printer Cable Modem Cables Terminal/Printer Cables, RJ-11 6-pin/4-wire to DB-9 The wiring diagram for an RJ-11 6-pin/4-wire to DB-9 terminal/printer cable is shown in Table 1.
PAGE 143
RJ-11 6 Pin/4-Wire to DB-25M Terminal Printer Cable Modem Cables Terminal/Printer Cables, RJ-11 6-pin/4-wire to DB-25 The wiring diagram for an RJ-11 6-pin/4-wire to DB-25 terminal/printer cable is shown in Table 1.
PAGE 144
RJ-11 6 Pin to DB-9F Terminal Printer Cable Cables EIA-232 PC Terminal Emulator Cables, RJ-11 6-pin to DB-9 The wiring diagram for an RJ-11 6-pin to DB-9 PC terminal emulator cable is shown in Table 1.
PAGE 145
RJ-11 6 Pin to DB-25M Terminal Printer Cable Cables Terminal/Printer Cables, RJ-11 6-pin to DB-25 The wiring diagram for an RJ-11 6-pin to DB-25 terminal/printer cable is shown in Table 1.
PAGE 146
RJ-45 4-Wire to DB-9M Terminal Printer Cable Software Flow Control Only Cables EIA-232 Terminal/Printer Cables, RJ-45 8-pin/4-wire to DB9 Software Flow Control Only The wiring diagram for an RJ-45 8-pin to DB-9 terminal/printer cable using only 4 wires is shown in Table 1.
PAGE 147
RJ-45 4-Wire to DB-25M Terminal Printer Cable Cables EIA-232 Terminal/Printer Cables, RJ-45 8-pin/4-wire to DB25 The wiring diagram for an RJ-45 8-pin to DB-25 terminal/printer cable using only 4 wires is shown in Table 1.
PAGE 148
RJ-45 (Altpin On) to DB-9M Terminal Printer Cable Terminal/Printer Cables, Altpin RJ-45 8-pin to DB-9 The wiring diagram for an altpin RJ-45 8-pin to DB-9 terminal/printer cable is shown in Table 1.
PAGE 149
RJ-45 to DB-25M Terminal Printer Cable Terminal/Printer Cables EIA-232 Terminal/Printer Cables, Altpin RJ-45 8-pin to DB25 The wiring diagram for an altpin RJ-45 8-pin to DB-25 terminal/printer cable is shown in Table 1.
PAGE 150
RJ-45 to DB-9M Terminal Printer Cable Cables Terminal/Printer Cables, RJ-45 8-pin to DB-9 The wiring diagram for an RJ-45 8-pin to DB-9 terminal/printer cable is shown in Table 1.
PAGE 151
RJ-45 10 Pin to DB-9M Terminal Printer Cable Cables EIA-232 Terminal/Printer Cables, RJ-45 10-pin to DB-9 Table 1: EIA-232 RJ-45 10-pin to DB-9 terminal/printer cable From Signal Direction Signal RJ-45 10 DCD 2 DSR 6 To DB-9 RTS 7 RxD TxD 3 5 TxD RxD 2 9 DTR DSR 6 DCD 1 7 SG SG 5 3 RTS CTS 8 8 CTS DTR 4 4 GND GND Shell * Arrows indicate which direction the signal is flowing NOTES: ● Altpin should be turned off when using this cable.
PAGE 152
RJ-45 10 Pin to DB-25M Terminal Printer Cable Cables EIA-232 Terminal/Printer Cables, RJ-45 10-pin to DB-25 The wiring diagram for an RJ-45 10-pin to DB-25 terminal/printer cable is shown in Table 1.