USER INSTRUCTIONS KP-632 KEYPANEL EKP-632 EXPANSION PANEL 9350-7711-000 Rev D, 8/2004
PROPRIETARY NOTICE The RTS product information and design disclosed herein were originated by and are the property of Telex Communications, Inc. telex reserves all patent, proprietary design, manufacturing, reproduction, use and sales rights thereto, and to any article disclosed therein, except to the extent rights are expressly granted to others. COPYRIGHT NOTICE Copyright © 2001 by Telex Communications, Inc. All rights reserved.
RETURN SHIPPING INSTRUCTIONS PROCEDURE FOR RETURNS If a repair is necessary, contact the dealer where this unit was purchased. If repair through the dealer is not possible, obtain a RETURN AUTHORIZATION from: Customer Service Department Telex Communications, Inc. Telephone: (877) 863-4169 Fax: (800) 323-0498 DO NOT RETURN ANY EQUIPMENT DIRECTLY TO THE FACTORY WITHOUT FIRST OBTAINING A RETURN AUTHORIZATION.
End-User License Agreement for Telex® Software IMPORTANT - Please read this document carefully before using this product. THIS DOCUMENT STATES THE TERMS AND CONDITIONS UPON WHICH TELEX COMMUNICATIONS, INC. (the “COMPANY”) OFFERS TO LICENSE THE INSTALLED SOFTWARE OR PROGRAM (the “SOFTWARE”) FOR USE WITH THE PRODUCT IN WHICH IT WAS INSTALLED. YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, DO NOT USE THIS PRODUCT.
TABLE OF CONTENTS Introduction 1-1 Description . . . . . . . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . . . . . . Options . . . . . . . . . . . . . . . . . . . . . . GPI/Connector Module . . . . . . . . . . . CSI-100 Coaxial System Interface Module . EKP-632 Expansion Keypanel . . . . . . . LCP-632 Level Control Panel. . . . . . . . MCP-90 Panel Microphone. . . . . . . . . Headsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Talk + auto mute . . . Talk + auto reciprocal Talk + auto table . . . All Call Key . . . . . . Talk + DIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display Menu, Panel ID . . . . . . . . . . . . . . . . . Display Menu, Version . . . . . . . . . . . . . . . . . . MENU SYSTEM, KEY ASSIGN MENU. . . . . . . . . . . General Procedure to use the Key Assign Menu . . . . Key Assign Menu, Matrix . . . . . . . . . . . . . . . . Key Assign Menu, Pt-to-Pt. . . . . . . . . . . . . . . . Key Assign Menu, Party Line . . . . . . . . . . . . . . Key Assign Menu, IFB . . . . . . . . . . . . . . . . . . Key Assign Menu, Spcl List . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . Environmental: . . . . . . . . . . . . . . . . . . . . . . . . . Approvals: . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors (Other connector options available) . . . . . . . . . . . Panel Microphone Connector (Electret) . . . . . . . . . . . . . . Headset Connector (Dynamic) . . . . . . . . . . . . . . . . . . Power Input Connector . . . . . . . . . . . .
S E C T I O N 1 I NTRODUCTION CHAPTER1 Description Figure 1.1 KP-632 keypanel front view. Listen Headset MENU Talk Vol. Sel. FWD Mic ------ ------ ------ ------ ------ -----KP-12 OKP4 ANDY12 KP-632 DAN KP96 ™ KP-632 BACK 1F0144 DAN456 SL0332 KP12-1 M00900 1 PL AUTO 2 3 IFB ISO PREFIX 4 5 RELAY TYPE COPY CW E-PNL 7 8 EX COPY DISPLAY 6 9 MULT Headset MUTE CLR Call waiting Listen 5 ------ ------ ------ WKP4-2 WKP4 NUM SLIST PHONE 0 PGM FUNC Vol.
• Upgradeable. Firmware updates can be received via the internet, for example, and then downloaded to the KP-632 via the intercom connection. Firmware is available in both English and Japanese Katakana character sets. • Optional General Purpose Interface (GPI)/Connector module: Can be installed either in the factory or in the field. Provides a variety of audio and logic inputs and outputs. • Optional EKP-632 Expansion Panel: Provides additional Talk/Listen keys for a total of 48 Talk/Listen keys.
EKP-632 Expansion Keypanel Figure 1.4 EKP-632 expansion keypanel front view. Provides an additional 24 intercom keys. LCP-632 Level Control Panel Figure 1.5 LCP-632 level control panel front view Provides easy adjustment of point-to-point and party line listen levels for individual intercom keys. One LCP-632/16 adjusts one row of keys.
1-4 KP-632 User Manual
S E C T I O N 2 I NSTALLATION CHAPTER2 Option DIP Switch Settings Switch 1: Latch Enable/Disable Default setting = Open: Enable. Note Description: An intercom key can always be turned on for momentary conversation by pressing and holding the key during the conversation. There is also an electronic latching feature that lets you tap intercom keys to turn them on or off. This permits convenient hands-free conversation. However it can also result in a talk circuit being left on unintentionally.
Switch 4: Call Flash Timeout Default setting = Open: 15 Second Flash. Note Description: Whenever there is an incoming call and there is a talk key assigned to the caller, the talk LED next to that key will flash. The flash can be set for 15 second timeout, or until the caller's talk key is released. Future versions of ADAMedit and ZEUSedit will be able to override the Call Flash Timeout setting. Switch 5: Footswitch Enable / Disable* Default = Open: Disabled.
Address Setting for Zeus Intercom port connectors on the Zeus back panel are arranged in three groups of eight intercom ports. For each group, intercom port connectors are labeled ID 1, ID 2, etc. When you connect a KP-632 keypanel to Zeus, set the Address switch to match the corresponding ID number on the Zeus back panel. Note that address switch settings 0, and 9 through F are not used. Address Setting for ADAM CS Each Audio I/O card contains 1 group of 8 intercom ports.
Figure 2.1 Address number vs intercom port numbers for 8-Port Audio I/O Cards (ADAM AND ADAM CS Intercom Systems. ADAM CS with 50-pin Telco back panel: Note 2-4 Determine the address setting from Figure 2.1. To use the table, locate the intercom port number to which the KP-632 will be connected. Then, read across to the "Address" column to find the Address number. Set the KP-632 Address switch to this number. Settings 0, and 9 through F are not used.
Address Setting for ADAM Each Audio I/O card contains 1 group of 8 intercom ports. Determine the address setting from Figure 2.1. To use the table, locate the intercom port number to which the KP-632 will be connected. Then, read across to the "Address" column to find the Address number. Set the KP632 Address switch to this number. Note: settings 0, and 9 through F are not used. Connections EXP. Connectors Connect from the Exp.
Figure 2.3 RJ12 Intercom Cable Wiring Power Supply Connector Align and insert the external power supply connector. Tighten the locking ring. Connect a power cord to the power supply and to an AC power source. The power supply accepts 100-240 VAC, 50/60 Hz. Note At power-up, the alphanumeric displays will first show asterisks (******). After several seconds to a minute the intercom key assignments will display.
Panel Microphone Connector A panel microphone may be connected for talking with either the front panel speaker or headphones used for listening. The connector accepts MCP90 Panel Microphones. Insert the microphone and rotate the entire microphone body several turns to lock in place. Panel Microphone Gain Adjustment The gain of the panel microphone preamp output to the matrix can be adjusted via the recessed trim pot located on the back panel.
This Page Left Blank Intentionally 2-8 KP-632 User Manual
S E C T I O N 3 B ASIC O PERATION CHAPTER3 Screen Saver Operation Note If the KP-632 is set for screen saver operation, the alphanumeric display automatically shuts off after several minutes of inactivity. The display reactivates on incoming call or when the keypanel operator actuates any control. DIP switch 3 turns enables/disables screen saver operation. You can override the normal timeout period for screen saver operation and immediately place the keypanel in screen saver mode.
Intercom Keys and Displays Alphanumeric Display Indications for Intercom Keys Upper Case Letters: Upper case letters indicate keys that have any kind of talk assignment, with or without a corresponding listen assignment. Example: DIR1 Lower Case Letters: Lower case letters indicate keys that have only a listen assignment. Example: dir1. Dashes ------: Dashes indicate a key that has no talk or listen assignment.
at the remote location if your keypanel has the lower trunk IFB priority. IFB trunk priorities are set in ADAMedit. (Click the "KP" button on the ADAMedit toolbar to access Keypanels / Ports setup, then click the "Edit" button, then click the "Advanced" tab. Enter the desired IFB priority in the fields provided. Be sure to send the change to the intercom system.) Flashing Green Talk LED & Display Alpha (on time equal to off time)* Note There is an incoming call from the destination assigned to the key.
Talk + auto reciprocal Listen will always be on, and talk may be turned on or off. Talk + auto table Note If an IFB talk key has an auto-table listen assignment, talk and listen can be independently activated. The listen key listens to whatever is defined as the IFB Listen Source for the IFB that is assigned to the talk key. A full explanation of the auto-table feature is beyond the scope of this manual.
click the "Advanced" tab. Place a check next to "Port is TIF". Remember to send the change to the intercom system.) Muting the Microphone Tap the MUTE key upward to turn microphone muting on or off. Note The Vol. Sel. display alternates between Hdst and Mute (or between Spkr and Mute) while the microphone is muted. While muting is on, you cannot be heard on the intercom, or by anyone on the telephone, or by any device connected to the mic preamp output of the optional connector module.
This Page Left Blank Intentionally 3-6 KP-632 User Manual
S E C T I O N 4 TELEPHONE O PERATION CHAPTER4 Note Telephone operations require an optional TIF-951 / TIF-2000 Telephone Interface. Also, you must first assign an intercom key to talk/listen to the TIF. We recommend a talk+auto listen assignment. Receiving A Phone Call Note When there is an incoming telephone call, the talk LED will flash red next to the KP-632 key that is assigned to the TIF. Activate the key to answer the call. The red flash for incoming TIF call is the default operation.
4 Activate the TIF talk key. The talk LED turns green, the "ON" LED at the TIF-951 / TIF-2000 activates, and you should hear dial tone at the KP-632. 5 Dial the telephone number. Digits scroll in the display above the TIF key. 6 When the far end answers, you can dial additional digits (to access a mail system or automated response system, etc.). When finished dialing, momentarily turn off the TIF talk key to end dialing mode (talk LED turns red). 7 Turn the TIF talk key back on for conversation.
5 After storing the autodial number, hang up using the KP9X hang-up sequence. Dialing an Autodial Number Stored in the TIF-951 / TIF-2000 1 Tap the PHONE key to activate dialing mode. 2 Tap "down" on the TIF talk key to latch it in the on position. 3 Tap CLR followed by the autodial number (01, 02, etc.). 4 When finished dialing, click the PHONE key again to exit dialing mode. 5 Hang up using theKP9X hang-up sequence.
Note If the far end answers, begin your conversation. After the far end answers, you may dial additional digits (to retrieve voice mail, log onto an automated answering system, etc.). Note 5 If there is no answer, or to hang up when finished talking, tap the BACK key. Hang up displays. Tap PGM to hang up. Occasionally, you may receive intercom an intercom caller name in the Call waiting window while you are talking on the phone.
S E C T I O N 5 KP9X S ERIES KEYPAD P ROGRAMMING CHAPTER5 Note A summary of the keypad programming sequences is located at the back of the manual for quick reference. KEYPAD PROGRAMMING, DISPLAY REQUESTS Display requests let you view information about the keypanel configuration. You can display information by two methods: either by entering sequences on the programming keypad, or by scrolling the names of display requests in the Call waiting window and then selecting the desired display request.
This sequence displays all listen key assignments for about 10 seconds. Lstn displays in the Call waiting window. Tap CLR to quit. Display Setup Page Assignments FUNC DISPLAY E-PNL Currently, there are four setup pages available for each keypanel. Each setup page defines a set of 16 talk and listen key assignments. Most RTS keypanels have a maximum of 16 keys, so one setup page is typically assigned to the main keypanel, and is referred to as the "Main" setup page.
Tone Generator Activation (FUNC-DISPLAY-7) FUNC DISPLAY 7 This sequence activates the keypanel's internal tone generator. You can use the tone generator to check the audio send and receive paths to and from the matrix. For example, you can assign a talk key on the keypanel to talk to itself. When you activate the talk key, you should be able to hear the tone from the keypanel speaker or from a headset. Note To turn off the tone generator, press the CLR key.
Notes • The same setup page cannot be assigned in more than one place. If a setup page is already assigned somewhere else, you must clear or change that assignment first. With the exception of the main row assignment, you can clear any page assignment from a row of keys by entering E-PNL 0 PGM, then pressing any key in the row.
3 Auto mute (listen keys only) 4 Auto reciprocal (listen keys only) 5 All call (talk level 1 only) 6 DIM (talk level 2 only, for point-to-point key, must enter 00 first) 7 Auto table (listen only, when talk level 1 is an IFB assignment) Note 4 Trunked intercoms only: (Skip when assigning auto functions or local key assignments.) Select an intercom matrix (tap 1 , or 2 etc.).
Note If a key will not accept an assignment, the destination that you are trying to assign may not have scrolling enabled in ADAMedit. Or, the key that you are trying to assign may be restricted in ADAMedit. Programming Key Assignments Using Alpha Scrolling Alpha scrolling lets you scroll through a list of names of ports, party lines etc. in the Call waiting window. Once the desired name is displayed in the window, you can copy it to a key.
2 Tap down on an intercom key to assign talk, or tap up to assign listen. Clearing a Key Assignment There are two ways to clear a key assignment: Method 1: Clearing the Call waiting Window and Copying it to a Key 1 Clear the Call waiting window, if necessary, by tapping up one or more times on the Call waiting key. 2 Tap the COPY CW key. 3 Tap the key that you want to clear. Tap up to clear listen, down to clear talk.
This Page Left Blank Intentionally 5-8 KP-632 User Manual
S E C T I O N 6 KP-632 M ENU S YSTEM CHAPTER6 Note A chart of the menu system is located at the back of the manual for quick reference. MENU SYSTEM, MENU ACCESS 1 Clear all names from the Call waiting display (if not clear) by tapping "up" one or more times on the Call waiting key. 2 Tap MENU to activate the menu system. 3 Press ↓↓ to scroll forward through the list of menus. Press − − to scroll back. 4 Tap FWD or PGM to enter a menu. Tap BACK to exit a menu.
Note • AC: All-call key. For descriptions of the various key assignment types, see the "GLOSSARY". Display Menu, Chans On Displays an alpha list, in the Call waiting window, of all intercom ports that currently have talk crosspoints closed to this keypanel. Chans On is typically used to locate an open mic or other open audio source that needs to be shut off. The most likely cause is typically a talk key that has been left on at some keypanel.
MENU SYSTEM, KEY ASSIGN MENU Use this menu to assign intercom keys, to adjust listen levels for point-to-point keys and party line keys, and to assign setup pages. General Procedure to use the Key Assign Menu 1 Clear the Call waiting window if necessary, by tapping upward one or more time on the Call waiting key. 2 Tap Menu 3 Tap ↓↓ to scroll down to the Key Assign menu. 4 Tap PGM or FWD to enter the menu. Note If you do not have a trunking intercom system, skip to step 6.
8 When the requested list is displayed, press ↓↓ or −− , to locate the desired assignment. 9 Tap PGM or FWD to select the assignment. 10 Talk Lvl 1 should now display in the Call waiting window. Press ↓↓ or −− if necessary to select a different option. Options are as follows: • Talk Lvl 1: Assigns only talk level 1. Leaves the listen assignment as is. • Listen: Assigns only listen. Leaves the talk assignment as is. • Talk + AF: Assigns talk level 1, with auto-follow listen.
Key Assign Menu, Party Line Assigns a key that talks and/or listens to a party line. The key will have no effect until members have been assigned to the party line in ADAMedit. Note that party lines members are usually nonkeypanel devices that cannot activate talk and listen paths. Therefore, if you want full communication with the party line, you will need to assign both talk and listen on the key. If all communications will normally be 2-way, you may wish to assign the key as Talk + auto listen.
• Auto Mute (AM, for listen keys only) • Auto Recip (AR, for listen keys only) • All Call (AC, for talk level 1 only) • Dim ( Dim Table function, for talk level 2 on point-to-point keys only) 2 Press FWD or PGM to select the desired auto function. 3 Tap Key displays. Tap an intercom key to assign the selected auto function. Tap up to assign all Notes auto functions except All Call or DIM. Tap down for All Call or DIM.
Key Assign Menu, Setup Page Use this menu item to change the setup page assignments on the KP-632 or EKP-632. One setup page is used for the top row of keys, and another setup page is used for the bottom row. 1 Press FWD or PGM to select Setup Page in the Key Assign menu. 2 Page 1 displays. 3 Press ↓↓ o r −− to select any of the following: Page 1: Assign setup page 1 to the KP-632 or EKP-632. Page 2: Assign setup page 2 to the KP-632 or EKP-632. Page 3: Assign setup page 3 to the KP-632 or EKP-632.
2 Tap any keys where you want to add a chime tone. Both LEDs will light red for the selected keys. 3 Tap CLR to exit. 4 Run Service Menu, Save Cfg, to store Chime settings. Note The chime option will continue on a key even if you change the key assignment. Removing the chime option from a key Repeat the procedure to add chime, but tap any keys where the LEDs are lit red to turn them off. Run Save Cfg to store the changes.
Key Option Menu, Solo A solo key will cause all other keys to turn off when activated. You can assign one solo key. 1 Select Solo then tap PGM. 2 Tap Key displays. 3 Tap a key. Both LEDs for the key will light red to confirm the assignment. Tap the key again if you made a mistake and want to remove the assignment. 4 Tap CLR when finished. 5 Activating the solo key should now cause all other activated keys to turn off. The keys will turn back on again when you turn off the solo key.
1 Select Dim, then tap PGM. 2 Speaker displays. To select headset, press ↓↓ . 3 Tap PGM. 4 By default, -8dB displays for speaker, and 0dB displays for headset. This is the default amount of dimming. 5 Press ↓↓ to increase the amount of dimming. Press −− .to decrease it. 6 Tap CLR to exit when finished. 7 The new dimming level is now set. 8 Run Service Menu, Save Cfg, to store the Dim setting. Service Menu, Disply Dim This item adjusts the alphanumeric display settings. 1. Select Disply Dim, then tap PGM.
Filtering Filtering lets you add a 9.6 kHz notch filter to one or more audio sources. This can be useful in a few cases when the keypanel data port signal is being heard in the audio line due to cable routing problems. 1 Select Filtering, then tap PGM. 2 Microphone displays. Press ↓↓ or −− .to display any of the following items: Microphone Matrix Aux 1 Aux 2 3 Tap PGM. 4 →None displays to indicate that no filtering is selected. 5 Press ↓↓. 6 Notch displays. 7 Press PGM. 8 →Notch displays.
2 Tap PGM. 3 Meter: Mic displays. Press ↓↓ or −− .to display any of the following items: Meter: Mic Meter: Mtx Meter: Aux1 Meter Aux 2 4 Tap PGM. 5 The Vol. bar graph is now monitoring the selected audio source. 6 Tap CLR to exit metering, or allow the metering function to timeout after about 1 minute. Mixing Mixing lets you route selected audio signals to the intercom system, to the speaker, or to the left or right headphone when using a headset.
Service Menu, LCD Bright This item allows you to adjust the brightness of the LCD backlighting so that the unit’s display can be viewed in a wide range of ambient room light conditions.The All selection controls the overall LCD brightness level including the right LCD on the KP-632. The Main selection controls the left LCD on the KP-632. The EXP1 controls the LCD on the EKP-632.
7 13-24: Skip displays. This indicates that the first connected LCP-632 will skip keys 13-24 and will attach to the next available row of keys. 8 Tap CLR to exit. 9 Run "Service Menu, Save Cfg", to store the new LCP-632 settings. Service Menu, Local GPIO If your KP-632 has an optional Connector Module, you can use this menu item to assign the GPIO inputs and outputs. Inputs can be assigned to activate intercom keys (including group master keys and a solo key). Outputs can be activated by intercom keys.
Removing an Input Assignment 1 Select GPIO, then tap PGM. 2 Press ↓↓ or −− if necessary to select Input. 3 Tap PGM. 4 Press ↓↓ or −− .to display the GPI input that you want to remove. 5 Tap PGM. 6 Press ↓↓ to select Not Asgnd. 7 Tap PGM. 8 →Not Asgnd displays. The arrow indicates that "Not Assigned" is the new selection. 9 Tap CLR to exit. 10 Run Service Menu, Save Cfg, to store local GPIO settings. Adding or Removing a GPI Output Key Assignment 1 Select Local GPIO, then tap PGM. 2 Input displays.
Service Menu, Mic Select This menu item allows the user to select between the Panel and Headset Mic. In the Normal (defualt) setting, audio from the Panel Mic used. In the Hdst Only, setting audio from the Headset Mic is used.This is used to force the use of the headset microphone even when the keypanel’s speaker is being used. 1 Select Mic Select from the Service menu, then tap PGM.
Figure 6.2 Mod ID assignments for the KP-632 and EKP-632. Note You do not need to run Save Cfg after changing Mod assignments. Service Menu, Output Level Allows the adjustment of the nominal audio output level to the matrix from 0 dB to +8 dB. 1 Select Outp Level, then tap PGM. 2 +8 dB displays. 3 −−decreases the level. 4 ↓↓ increase the level. 5 Tap PGM. 6 Tap CLR to exit. 7 Run Service Menu, Save Cfg, to store the Output Level settings.
Service Menu, Reset Cfg Reset Cfg restores all custom settings to the defaults and erases all stored autodial numbers. Service Menu, Save Cfg Save Cfg PGM saves custom settings that you have made in the Key Option or Service menus. made in the After customizing settings in the Key Option and Service menus, run Save Cfg to store your custom settings in non-volatile memory. This will assure protection of you settings when the keypanel is powered down.
S E C T I O N 7 S PECIFICATIONS CHAPTER7 Microphone Preamplifier Panel Mic (Electret) Input Level: -42 dB, 150 ohms @ 1 kHz Headset Mic (Dynamic) Input Level: -50 dBm, 150 ohms@ 1 kHz Output Level (to matrix): +8 dBu, ± 0.
Volume Control Range: 52 dB Speaker Rating: 4 watts max Intercom Balanced Line Input/Output Input Level: Nominal: +8 dBu. Peak: ± 20 dBu max.
Pin-out: Pin 1: Mic low Pin 2: Mic high Pin 3: Common Pin 4: Headphone left high Pin 5: Headphone right high Power Input Connector Type: 5-pin locking DIN Pin-out: Pin1: Common Pin2: Common Pin3: +5VDC, 1.50A Max. Pin4: -15VDC, 0.150A Max. Pin5: +15VDC, 0.5A Max.
LCP Connector Type: RJ45 GPI Module Conntectors (Optional) Aux 1 In (Auxiliary program input 1) Type: 3-pin female XLR Pin-out: Pin 1: Ground Pin 2: Input + Pin 3: Input - Aux 2 In (Auxiliary program input 2) Type: 3-pin female XLR Pin-out: Pin 1: Ground Pin 2: Input + Pin 3: Input - Notes Balanced input, +8dBu nominal Relay 1 & 2 Out Type: 9-pin male D-Sub Pin-out: Pin 1: NC contact 1 Pin 2: COM contact 1 Pin 3: NO contact 1 Pin 4: NC contact 2 Pin 5: COM contact 2 Pin 6: NO contact 2 Pin 7:
Pin 6: NO contact 4 Pin 7: +5 VDC Pin 8: Ground Notes Pin 9: +5 VDC The relay 1 and 2 contacts are electrically separate, but operate in unison. The relay 3 and 4 contacts are electrically separate, but operate in unison. The +5 VDC pins are connected internally through 1K resistors to +5 VDC and can source 5 mA. This voltage can be used with the relay contacts to create an active high output for some devices that require a +5 VDC signal to activate.
Pin-out: Pin 1: Gnd Pin 2: N/A leave unconnected Pin 3: N/A leave unconnected Pin 4: N/A leave unconnected Pin 5: Balanced dynamic mic input + Pin 6: Gnd Pin 7: Headset Listen Out Left Pin 8: Headset Listen Out Right Note Pin 9: Balanced dynamic mic input Mic input -60 dBu nominal. Headset out 0.325 watts into 8 ohms.
S E C T I O N 8 KP9X KEYPAD S EQUENCE Q UICK R EFERENCE CHAPTER8 KP9X DISPLAY SEQUENCES FUNC DISPLAY 0 . Diagnostics mode. FUNC DISPLAY 1 . Display port number. FUNC DISPLAY 2 . Display level 2 talk assignments. FUNC DISPLAY 3 . Display listen assignments. FUNC DISPLAY -8 Display setup page assignments. FUNC DISPLAY ID PGM: ↓↓ or − − to select items as follows: Display the calculated port number. CLR to end. Lev2 PGM: Display level 2 talk assignments. CLR to end.
3 Tap PGM. 4 Tap any key in top row to assign page to top row. Tap any key in bottom row to assign page to bottom row. KEY ASSIGNMENTS USING KEYPAD NUMERIC ENTRY 1 For talk level 2 assignment only: Tap 0 0 . 2 Select the key assignment type: NUM Intercom port. PL Party line. AUTO Auto function. FUNC SLIST Special list. FUNC IFB IFB FUNC ISO Camera ISO FUNC RELAY Relay or GPI output.
KP9X Dial Sequence 1 Activate the TIF listen key (listen LED green). 2 Make sure the TIF talk key is off (Talk LED off). 3 On the keypad, tap CLR-PHONE-PGM. 4 Activate the TIF talk key (talk LED turns green). The "ON" LED at the TIF-951 / TIF-2000 will activate, and you should hear dial tone at the KP-632. 5 Dial the telephone number. Digits scroll in the display above the TIF talk key. 6 When the far end answers, you can dial additional digits (to access a mail system or automated response system, etc.).
This Page Left Blank Intentionally 8-4 KP-632 User Manual
S E C T I O N 9 KP-632 MENU S YSTEM Q UICK R EFERENCE CHAPTER9 MENU ACCESS 1 Clear all names from the Call waiting display (if not clear) by tapping "up" one or more times on the Call waiting key. 2 Tap MENU to activate the menu system. 3 Press ↓↓ to scroll forward through the list of menus. Press − − to scroll back. 4 Tap FWD or PGM to enter a menu. Tap BACK to exit a menu. 5 Within a menu: • Press ↓↓ or − − to scroll. • Tap FWD or PGM to select an item.
DISPLAY MENU KEY ASSIGN MENU * Run Save Cfg, to save these settings.
This Page Left Blank Intentionally 9-3
9-4 KP-632 User Manual
S E C T I O N 10 M ODE 2 O PERATION CHAPTER10 Section 2 Switch 4: Call Flash Timeout* When the switch is closed the menu and indefinite talking is disabled. Switch 5: Footswitch Enable / Disable* Amber talk LEDs indicate a latched talk key. Section 3 LED Indications for Intercom Keys Talk LED Indications The talk LED is the lower LED for each key. The talk LED indications are as follows: Continuous Red* Talk is on and the keypanel operator can be heard at the destination.
Solid Red Talk LED & Flashing Display Alternating Pattern of Alpha & (-**-) ("Busy") Note You cannot talk at this time. This indication occurs when you activate a local IFB key that is already in-use by a keypanel with a higher IFB priority. It also occurs when you activate any key assigned to a remote destination, but there are currently no trunks available.
S E C T I O N 11 G LOSSARY CHAPTER11 All Call Alpha Auto Follow (AF) Auto Functions Auto Listen (AL) Auto Mute (AM) Auto Reciprocal (AR) Auto Table (AT) For talk key assignment only. Activating an All Call key will also activate all talk keys to the left of the All Call key (up to, but not including another All Call key). Alphas are the user-changeable names which identify destinations (intercom ports, party lines, etc). Change Alpha names for intercom ports using the Port Alpha button in ADAMedit.
Crosspoint Destination Dim GPIO IFB 11-2 The term "Crosspoint", like the term "Matrix" is inherited from intercom systems, such as the RTS CS9500, CS9600, and CS9700, that use a switching matrix to route intercom audio. In those systems, the crosspoints are the actual switches that close or open to connect or disconnect talk and listen paths.
ISO (Camera ISO) Matrix Party Line (PL) Port music can be interrupted while someone is talking over the PA.IFB's are set up by defining the IFB inputs and outputs using the intercom system configuration software. The intercom output port is called the IFB output and the program input port is called the IFB input. IFBs can also be given names which are meaningful to keypanel operators.
Relay Special List Stacked Key 11-4 button in ADAMedit, then press F1 on the computer keyboard if you need help.)Intercom Data Groups and Port Number CalculationFor data routing purposes, port numbers are arranged in groups of 8 sequential intercom ports. In an ADAM or ADAM CS Intercom System, each Audio I/O card comprises one data group. In a Zeus Intercom System, each group of 8 port connectors comprises a data group. Within each data group, each keypanel is uniquely identified by its address setting.
Talk Level 1 Talk Level 2 Trunking Talk level 1 is the normal talk key assignment. This is the assignment that normally appears in the alphanumeric display (on keypanels so equipped). You may add a talk level 2 assignment to activate a second device along with talk level 1. Talk level 2 is used with stacked talk keys. A stacked talk key activates two types of communication at once.
This Page Left Blank Intentionally 11-6 KP-632 User Manual
RVON 1 RTS Voice Over Network Interface Card for the KP-32 and KP-812 Family of Keypanels ADDENDUM
2 RVON-1 User Manual
Proprietary Notice The RTS product information and design disclosed herein were originated by and are the property of Telex Communications, Inc. Telex reserves all patent, proprietary design, manufacturing, reproduction, use and sales rights thereto, and to any article disclosed therein, except to the extent rights are expressly granted to others. Copyright Notice Copyright 2004 by Telex Communications, Inc.. All rights reserved.
4 RVON-1 User Manual
Contents General Description of the RVON-1 Voice Over Network Card ............................................................7 Features ..............................................................................................................................................7 Specifications ......................................................................................................................................8 Digital .......................................................................
This Page Intentionally left blank.
Chapter 1 Introduction General Description of the RVON-1 Voice Over Network Card Installed directly into KP-32 or KP-812 keypanels, the RVON-1 provides voice over IP (Internet Protocol) communications for the RTS™ ADAM intercom family. In general, voice over IP means sending voice information in digital form using discrete packets rather than the traditional hardwire connection. The RVON-1 delivers an integrated solution for connecting keypanels to the Intercom matrix over standard IP networks.
Specifications Digital Compression Audio Bit Rate Coding Delay Playout Delay IP Bandwidth G.711 G.729AB G.723 64k 8k 5.3k/6.3k 125µs 10ms 30ms 20-60ms 20-120ms 60-120ms 160-224 kbps 32-112 kbps 29-45 kbps * Data depends on CODEC selection Note: The Playout Delay and Bandwidth depend on the configured amount of audio per packet. Connections - RJ-45 Ethernet via backcard - 14-pin KP Compatible Expansion Connector Pin 1 ................................................................................
Firmware Compatibility Requirements for the RVON-1 Card Des c r i p t i o n Ver s i o n Master Controller 9.19.0 or later Peripheral Controller 10.10.0 or later DBX 1.10.1 or later AZedit 2.06.06 or later RVON-8 1.1.0 or later KP-32 2.0.0 or later Table 1. Compatibility Requirements for the RVON-1 Card Flash Chip Replacement The KP32, KP-32J , KP-632, and KP-832 must upgraded to 4MB flash chips that are programmed in the factory. Note, there are two chips for each model (see figure 1).
Installation of the RVON-1 Card Before using the RVON-1 card with the KP-32, a few modifications need to be made to the keypanel. If the serial number on your KP-32 keypanel is 61170, you will need to update your backpanel with the Ethernet RJ45 connection (part number - 9080-7656-002) knockout present. Also, the KP-32 flash chips need to be replaced with larger flash chips (4MB) (see the chart on page 9 for the flash chip part numbers. To Install the RVON-1 Card, do the following: 1.
Installation of the RVON-1 Card (cont.) In the KP-32 keypanel, the RVON-1 card connects to the KP-32 by way of the J2 connector on the RVON-1 attached to J4 on the KP-32 header. Gently secure the board in place. See Figure 4. Figure 4. The J4 connector on the KP-32 board. Figure 5. The J37 connector on the KP-812 board. In the KP-812, the RVON-1 card connects to the KP-812 by way of the J2 connector on the RVON-1 attached to J37 on the KP-812 header. Gently secure the board in place. See Figure 5.
Configure the RVON-1 from the KP-32 To use the RVON-1 with the KP-32, the KP-32 firmware must be at V 2.0.0 or higher. In turn, the firmware requires that larger flash chips be used as well. For more information, see page 9. TOP LEVEL MENU, SERVICE, RVON SETUP Set the IP Address from the Service Level Menu The RVON-1 card, when shipped has a default IP Address already configured.
NOTE: Once you have entered the Netmask, you may need to enter the Gateway IP Address. A Gateway is a node (for example, a computer) on a network that serves as an entrance to another network. 16. 17. 18. Press PGM. The actual Gateway IP Address appears. Enter the first number in the Gateway IP Address. This activates the first octet of the Gateway IP Address and clears the rest of the address. Press PGM. This confirms the first octet in the Gateway IP Address and moves you to the second octet.
Configure the RVON-1 from the KP-812 TOP LEVEL MENU, SERVICE, RVON SETUP Set the IP Address from the Service Level Menu The RVON-1 card, when shipped has a default IP Address already configured. This must be changed in order for the RVON-1 card to function properly because the pre-configured IP Address may not work with your network. To set the IP Address, do the following: 1. On the KP-812, scroll to Menu. The top level menu appears . 2. Using the encoder knob, scroll to Service. 3. Tap the encoder knob.
NOTE: Once you have entered the Netmask, you may need to enter the Gateway IP Address. A Gateway is a node (for example, a computer) on a network that serves as an entrance to another network. 16. 17. 18. Tap the encoder knob. The actual Gateway IP Address appears. Enter the first number in the Gateway IP Address. This activates the first octet of the Gateway IP Address and clears the rest of the address. Tap the encoder knob.
Configure the RVON-8 using AZedit to contact the RVON-1 To configure the RVON-1 card, do the following: 1. 2. From the Status menu, select I/O Cards. The I/O Card Status screen appears showing the types of installed cards. Right click on an RVON-8 card and select RVON-8 Configuration. The RVON-8 Configuration screen appears. NOTE: The RVON-8 you use should be already configured. If it is not configured, refer to your RVON-8 Card User Manual.
6. 7. 8. From the Device Channel drop down list, select Channel 1. There may be two channels listed, but the connection can only be made through channel 1. From the CODEC Type drop down list, select the CODEC type. From the Packet Size drop down list, select the size of each audio packet. NOTE: A CODEC is an algorithm used to compress audio. Codecs dictate the quality of audio you hear and the network bandwidth used.
5. Using the Browse feature, browse to the file to be downloaded. 6. Click Open. The Download Device Firmware screen appears. 7. Click Begin Download. The download begins. 8. Click OK. The RVON-1 firmware download is complete. This takes a minute or two to occur. WARNING! - 9. NOTE: 18 Do NOT power down the keypanel until you have verified the new version information from AZedit.
Appendix A Basic Network Configuration This section covers basic network configuration set up and testing. Also covered are basic concepts and operations, including the difference between LAN and WAN networks and how IP Addressing is used. In a networked environment, such as a company, typically there are many computers connected together using a router or a switch (for more information router or switch in the definitions section).
Wide Area Network A wide area network connects two or more LANs and can span a relatively large geographical area. For example, Telex Headquarters in Burnsville, MN is connected to several branch offices in Nebraska and Arkansas over the wide area network. The largest WAN in existence is the Internet. Figure 2. Wide area network diagram Accessing the Wide Area Network (WAN) Figure 3 shows LAN IP addresses using a common IP address, 10.2.100.x (192.168.x.x is another common address).
Network Address Translating (NAT) Using the initial IP address, then converting it to a valid WAN IP address is how the network address translation works in theory. Once the IP address is changed, it is up to the network interface device (such as a router, gateway, switch, etc. ) to keep track of which computers are talking on which ports.
Po r t Nu m b er Des c r i p t i o n 1 TCP Por t Service Multiplier 5 Remote Job Entry 7 ECHO 18 Message Send Protocol (MSP) 20 FTP-Data 21 FTP - Control 23 Telnet 25 Simple Mail Transfer Protocol (SMTP) 29 MSG ICP 37 Time 42 Host Name Server (Nameserv) 43 Whols 49 Login Host Protocol (Login) 53 Domain Name Server (DNS) 69 Trivial File Transfer Protocol (TFTP) 70 Gopher Service 79 Finger 80 HTTP 103 X.
IP Addresses If you do not know your IP Address, you can open a DOS screen in Windows®- based environment and bring up the ipconfig screen. To find your IP Address using ipconfig, do the following: 1. From the Start Menu, open a Command Prompt window. 2. At the prompt, type ipconfig, then press Enter. The IP configurations appear for your machine, such as the DNS suffix, IP Address, Subnet Mask, and Default Gateway. 3. At the prompt, type Exit to close the screen.
Ping a Computer Pinging a computer on the network makes sure it is able to be “seen” and receive messages on the network. Note: You can also ping your RVON-8 card to verify that it is responding over the network by putting the cards IP address in place of the computer IP address. To ping a computer on the network, do the following, 1. From the Start Menu, open a Command Prompt window. 2. At the prompt, type the IP Address of the computer you want to ping (for example, 10.2.100.130). 3. Press Enter.
Possible Pitfall with Routers, Gateways, and Switches Anytime computers communicate through routers, gateways, and switches, they may be allowed or denied the connection. Network interface devices can be configured to block specific outgoing requests, as well as incoming requests, based on the IP address and/or port. This is one of the security mechanisms of a router. This also happens when broadcast messages are sent and received.
RVON-1 Specific Configuration RVON-1 cards use ports for communication of audio and control packets. Because routers can be configured to block certain incoming and outgoing requests, you will need to open the following ports in your network to allow WAN connections to and from a Network Interface Device. See Table 4 for the ports that need to be opened for the RVON-1 card to operate properly.
Network Terminology Bridges - A bridge is a device that connects two LANs, or two segments of the same LAN that use the same protocol. Sometimes called “transparent bridges”, they work at the OSI model Layer 2. Simply put, they are not concerned with protocols. Their main job is to pass data to a destination address that is predetermined in the data packet. With a bridge, all you computers are on the same network subnet (see Subnet).
LAN - A LAN is a computer network that connects a relatively small area (a single building or group of buildings). Most LANs connect workstations and computers to each other. Each computer (also know as a “node”), has its own processing unit and executes its own programs; however, it can also access data and devices on the LAN. This means that many users can access and share the same information and devices. A good example of a LAN device is a network printer.
Appendix B Telnet & Serial Port Programming of the RVON-1 Card RVON Serial and Telnet Commands RVON-1 card programming can also be done via a direct serial or Telnet connection. There are two physical connections to an RVON-1 board: • Direct serial through a custom debug cable (J3 6-pin bottom front) The custom debug cable always functions as the general-purpose debug tool.
3. Press Enter. The RVON login screen appears. 4. In the logon field, type the RVON login (default = Telex). 5. Press Enter. 6. In the password field, type the RVON password (default = password). 7. Press Enter. A prompt appears. 8. Type dbgcmd to access the debug command screens. 9. Press Enter. An MXP prompt appears. Table 1 is a list of commands support from the MXP Shell Prompt.
Co m m an d Par am et er 1 Par am et er 2 set rvon Des c r i p t i o n Help screen which lists all "set rvon" commands set rvon ip_addr X.X.X.X Set the IP address for the RVON-1 card set rvon netmask X.X.X.X Set the Network Mask for the RVON-1 card set rvon gateway X.X.X.
Coding Profiles Codec Codec Rate Audio (ms) / Packet Packets / Second Encoded Audio (bytes) IP Overhead (bytes) Total Packet Size (bytes) Bandwidth (Bytes/sec) Bandwidth (kbps/side) Bandwidth (kbps/channel) 0, 3, 6, 9 G.711 64k 10 100.00 80 60 140 14000 112 224 1, 4, 7, 10 G.711 64k 20 50.00 160 60 220 11000 88 176 2, 3, 8, 11 G.711 64k 30 33.33 240 60 300 10000 80 160 12, 16 G.729 8k 10 100.00 10 60 70 7000 56 112 13, 17 G.729 8k 20 50.
All are “set channel #” commands because they are for each audio channel. ENVIRONMENT VA RIA B L E NA ME COMMA ND VA L UE DESCRIPTION dest_ip RVON_DEST_IP_# (0,1) X.X.X.
Jumpers and Connections A selectable RS232/485 serial port is at connector J1. Jumper connections on J10, J11, and J12 select the signal mode on J1. • When J10, J11, and J12 are jumped from pins 1 to 2 - J1 is configured for RS485. • When J10, J11, and J12 are jumped from pins 2 to 3 - J1 is configured for RS232. J21 must be jumped from pins 1 to 2 to select UART B for RS485 RVON-1 keypanel operation. J2 Connector The RVON-1 card is designed to be used with either a keypanel or an RVON-IO card.
RVON-1 User Manual 35
