Operating Instructions
Table Of Contents
- CHAPTER 1 Introduction
- CHAPTER 2 BTR-800 Base Station
- CHAPTER 3 TR-800 Beltpack
- CHAPTER 4 TR-825 Beltpack
- CHAPTER 5 Initial Equipment Setup
- Unpacking
- Antenna Connection
- Antenna Polarization
- Distance between Antennas
- Antenna Placement
- Improving Reception and Increasing Range
- Base Station Set-up
- Location
- Power Connection
- Transmit Switches
- Internal Transmit Switches
- Intercom Switch
- Intercom Interface
- Dual Listen Functionality
- Auxiliary Input/Output
- Internal Auxiliary Input Routing Switch
- Stage Announce / Relay Contacts
- Base Station Link
- Beltpack Setup
- Antenna Connection
- Transmit Mode
- Headset Connection
- CHAPTER 6 Pre-Walk-Thru Checklist
- CHAPTER 7 System Operation
- Frequency Plan Overview
- Factory-Defined Groups
- User-Programmable Groups
- System Quick Start
- Base Station Operation
- Power
- Local Headset
- Portable Station Connect
- Intercom A and B
- Auxiliary
- Display Contrast
- BTR-800 Menu Structure
- Main Screen Flowchart
- Power-Up Screen
- Operating Screen
- Beltpack Activity Code Definitions
- Group/Channel Select
- Group/Frequency Select
- Frequency Edit (User-Programmed Groups Only)
- ClearScan™
- Special Key Sequences
- Lockout
- Copy
- 1st Use Default
- Factory Default
- Beltpack Operation
- On/Off and Volume Control
- Battery Check
- Talk Button
- Microphone Gain
- Audio Channel Select Button
- Stage Announce (SA)
- Wireless Talk Around (WTA)
- TR-800 Menu Structure
- Beltpack Menu Structure
- Power-Up Screens
- Group/Channel Screen
- Transmit Screen
- Receive 1 Screen
- Receive 2 Screen
- ClearScan™
- Stage Announce Enable/Disable
- Wireless Talk Around Enable/Disable
- Audio Channel A or B Disable/Enable
- Talk Button Latch on/Latch off
- Special Key Sequences
- Lockout
- 1st Use Default
- Factory Default
- TR-825 Menu Structure
- CHAPTER 8 System Walk-Thru
- CHAPTER 9 Troubleshooting
- CHAPTER 10 Tech Tips
- CHAPTER 11 Battery Information
- CHAPTER 12 Intercom Systems Specifications
- CHAPTER 13 Accessories and Replacement Parts
- CHAPTER 14 Certification Information
- CHAPTER 15 Three Band Base Stations
BTR-800, TR-800, TR-825 System Operation 45
Frequency Edit
(User-Programmed Groups Only)
This menu only occurs for user-programmable groups or when
copying to a user-programmable group. The Frequency Edit
screen allows the user to set the group transmit frequencies and
receive channel frequencies of a user-programmable group.
• Press [MENU] three times to go to the frequency select
screen from the operating screen. Press [SET] to start the
group number flashing. This screen allows the user to set
the group and frequencies of user-programmed groups only.
• Press the [UP]/[DOWN] arrows to change the group
number. The frequencies listed will reflect what is currently
in that group, Dashes will be displayed in any slots that are
not defined yet. Pressing [SET] will select the group and
start the selecting of frequencies within that group. The T1
frequency will start flashing.
• Pressing the [UP]/[DOWN] arrows will change the
frequency of T1 in 25kHz steps. Pressing [SET] will accept
the change and start you editing T2. If you had not pressed
the arrow keys when the frequency was flashing, but instead
press [SET], you would have skipped to the next frequency
to edit.
• After editing the transmit and the receive channel
frequencies, pressing [SET] will save that last frequency
and send you over to the beginning of the group/frequency
select screen with nothing flashing. NOTE: Once the end of
the displayed channel list is reached, the last displayed
channel location will scroll to allow the user to edit the
remaining channels.
• After action has occurred in the frequency edit screen
pressing [MENU] will take you one menu back to the
group/frequency select screen so that the user may see what
frequencies the base receivers are now on. If no action had
occurred, then pressing [MENU] will take you to the
operating screen. NOTE: Besides a group change, any
editing that occurs within this screen to frequencies DOES
NOT take effect until the user exits the screen via setting the
last channel or press [MENU].