USER INSTRUCTIONS KP-632 KEYPANEL EKP-632 EXPANSION PANEL UP TO AND INCLUDING VERSION 2.1.
PROPRIETARY NOTICE SHIPPING TO THE MANUFACTURER The product information and design disclosed herein were originated by and are the property of Bosch Security Systems, Inc. Bosch reserves all patent, proprietary design, manufacturing, reproduction, use and sales rights thereto, and to any article disclosed therein, except to the extent rights are expressly granted to others. All shipments of product should be made via UPS Ground, prepaid (you may request from Factory Service a different shipment method).
Table of Contents INTRODUCTION ..................................................3 BASIC OPERATION ........................................... 13 Description ................................................................3 Features .....................................................................3 Options ......................................................................4 Screen Saver Operation .......................................... 13 Selecting Headset or Speaker ...........................
TELEPHONE OPERATION ................................19 Receiving A Phone Call .......................................... 19 Dialing And Hanging Up Using KP9x Keypad Sequences .............................. 19 KP9X KEYPAD HANG-UP SEQUENCE ............................. 19 KP9X MANUAL DIAL SEQUENCE .................................... 19 KP9X REDIAL SEQUENCE .............................................. 20 KP9X AUTODIAL SEQUENCES ........................................
SERVICE MENU, OUTPUT LEVEL ....................................46 SERVICE MENU, PREAMP OUT (GPI OPTION ONLY) ......46 SERVICE MENU, RESET CFG ..........................................47 SERVICE MENU, RVON SETUP (RVON OPTION ONLY) ..47 SERVICE MENU, SAVE CFG ............................................47 SERVICE MENU, SCR SAVER ...........................................47 SERVICE MENU, SIDETONE .............................................48 SERVICE MENU, SNOOP TALLY .......................................
List of Figures FIGURE 1. FIGURE 2. FIGURE 3. FIGURE 4. FIGURE 5. FIGURE 6. FIGURE 7. FIGURE 8. FIGURE 9. FIGURE 10. FIGURE 11. FIGURE 12. FIGURE 13. FIGURE 14. FIGURE 15. FIGURE 16. KP-632 Keypanel Front View ...............................................................................................................3 GPI Connector Module .........................................................................................................................
CHAPTER 1 Introduction Description FIGURE 1. KP-632 Keypanel Front View The RTS Model KP-632/24 Keypanel mounts in a standard 19” equipment rack, is two rack spaces high and has 24 lever keys: 22 keys for intercom talk/listen assignment; 1 key for call waiting respond/clear; and 1 key for headset/microphone switching. The KP-632/24, like the KP-32 keypanel, combines all of the programmable features of the KP-9X and KP-12 series of keypanels.
• Upgradeable. Firmware updates can be received via the internet, for example, and then downloaded to the KP-632 via the intercom connection. Firmware is available in both English and Japanese Katakana character sets. • Optional General Purpose Interface (GPI)/Connector module: Can be installed either in the factory or in the field. Provides a variety of audio and logic inputs and outputs. • Optional EKP-632 Expansion Panel: Provides additional Talk/Listen keys for a total of 48 Talk/Listen keys.
CSI-100 Coaxial System Interface Module FIGURE 3. KP-632 CSI-100 coaxial system interface board. Provides the ability to link the unit to the matrix using a single 75 Ohm coaxial cable. The interface converts all audio and data streams to a single transmission path. Perfect for systems where there are existing, but unused 75 Ohm video cable. Requires a CSI-200 interface unit at the intercom matrix end. EKP-632 Expansion Keypanel FIGURE 4.
MCP-90 Panel Microphone Part Number Description MCP-90-3 3” electret panel microphone MCP-90-8 8” electret panel microphone MCP-90-12 12” electret panel microphone MCP-90-18 18” electret panel microphone Headsets Part Number 6 Description 300852-202 PH-88R5 Single sided intercom headset fitted with A5M 300853-501 PH-44R5 Binaural intercom headset fitted with A5M
CHAPTER 2 Installation Option DIP Switch Settings Switch 1: Latch Enable/Disable Default setting = Open: Enable. Description: An intercom key can always be turned on for momentary conversation by pressing and holding the key during the conversation. There is also an electronic latching feature that lets you tap intercom keys to turn them on or off. This permits convenient hands-free conversation. However it can also result in a talk circuit being left on unintentionally.
Switch 4: Call Flash Timeout Default setting = Open: 15 Second Flash. Description: Whenever there is an incoming call and there is a talk key assigned to the caller, the talk LED next to that key will flash. The flash can be set for 15 second timeout, or until the caller's talk key is released. NOTE: Future versions of AZedit will be able to override the Call Flash Timeout setting. Switch 5: Footswitch Enable / Disable* Default = Open: Disabled.
Address Setting for Zeus Intercom port connectors on the Zeus back panel are arranged in three groups of eight intercom ports. For each group, intercom port connectors are labeled ID 1, ID 2, etc. When you connect a KP-632 keypanel to Zeus, set the Address switch to match the corresponding ID number on the Zeus back panel. Note that address switch settings 0, and 9 through F are not used. Address Setting for ADAM CS Each Audio I/O card contains 1 group of 8 intercom ports.
ADAM CS with 50-pin Telco Back Panel Determine the address setting from Table 1 on page 9. To use the table, locate the intercom port number to which the KP-632 will be connected. Then, read across to the Address column to find the Address number. Set the KP-632 Address switch to this number. NOTE: Settings 0, and 9 through F are not used. Address Setting for ADAM Each Audio I/O card contains 1 group of 8 intercom ports. Determine the address setting from NOTE:.
FIGURE 7. RJ12 Intercom Cable Wiring Power Supply Connector Align and insert the external power supply connector. Tighten the locking ring. Connect a power cord to the power supply and to an AC power source. The power supply accepts 100-240 VAC, 50/60 Hz. At power-up, the alphanumeric displays will first show asterisks (******). After several seconds to a minute the intercom key assignments will display.
Panel Microphone Connector A panel microphone may be connected for talking with either the front panel speaker or headphones used for listening. The connector accepts MCP90 Panel Microphones. Insert the microphone and rotate the entire microphone body several turns to lock in place. Panel Microphone Gain Adjustment The gain of the panel microphone preamp output to the matrix can be adjusted via the recessed trim pot located on the back panel. Turn the pot clockwise.
CHAPTER 3 Basic Operation Screen Saver Operation If the KP-632 is set for screen saver operation, the alphanumeric display automatically shuts off after several minutes of inactivity. The display reactivates on incoming call or when the keypanel operator actuates any control. DIP switch 3 turns enables/disables screen saver operation. NOTE: You can override the normal timeout period for screen saver operation and immediately place the keypanel in screen saver mode.
Intercom Keys and Displays IMPORTANT: When using an AIO-8 or AIO-16 with a SCSI connector, or a Zeus Intercom System, only keypanels with the same alpha size can be used. To set the alpha size in AZedit go to the Alphas page in the Application Preferences notebook (in AZedit, Options|Preferences|Alphas). For more information, see the AZedit User Manual, which can be found at www.rtsintercoms.com.
Continuous Red Talk LED & Flashing Display Alpha (“In-use”)* The key is off, but someone is talking to the destination. This indication is provided for any local PL, IFB, ISO, or TIF key. It does not apply to remote IFB or ISO keys. This indication is provided so keypanels operators know when critical director communications are occurring.
Intercom Key Operation Basic Intercom Key Operation The up position of an intercom key activates listen (if assigned). The down position activates talk (if assigned). If there is no talk assignment for an intercom key, the talk position of the key will not activate. If there is no listen assignment, the listen position will not activate. For momentary activation of a key press and hold the key. Then, release it when finished. For latching operation (if enabled), tap a key; it will turn ON and remain ON.
Talk + DIM If a point-to-point key has the DIM function as a level 2 talk assignment, activating the key will cause the crosspoint levels to diminish for any other intercom ports that are currently listening to the same destination and that are in the same DIM table. NOTE: A full explanation of DIM tables is beyond the scope of this manual. For more information, see the AZedit User Manual, which can be found at www.rtsintercoms.com.
Call Waiting Operation Occasionally, a keypanel may call, and there won't be a key assigned to talk back to that caller. In this case, the caller's name will appear in the call waiting window. Press down and hold the call waiting key to talk back. To clear a name from the call waiting window, do the following: > Tap up on the call waiting key. If a second call is received in the call waiting window while a caller name is already displayed, the Call waiting LED will flash red.
CHAPTER 4 Telephone Operation NOTE: Telephone operations require an optional TIF (Telephone Interface). Also, you must first assign an intercom key to talk/listen to the TIF. We recommend a talk+auto listen assignment. Receiving A Phone Call When there is an incoming telephone call, the talk LED will flash red next to the KP-632 key that is assigned to the TIF. Activate the key to answer the call. Alternatively, there is an audible indication generated by the TIF unit for incoming calls.
4. Dial the telephone number. Digits scroll in the display above the TIF key. 5. When the far end answers, you can dial additional digits (to access a mail system or automated response system, etc.). 6. When finished dialing, momentarily turn off the TIF talk key to end dialing mode (talk LED turns red). 7. Turn the TIF talk key back on for conversation. To end the call, do the following: 1. Turn the TIF talk key off. 2. Tap PHONE CLR. 3. Tap the TIF talk key.
Dialing an Autodial Number Stored in the TIF 1. Tap the PHONE key to activate dialing mode. 2. Tap down on the TIF talk key to latch it in the on position. 3. Tap CLR followed by the autodial number (01, 02, etc.). 4. When finished dialing, click the PHONE key again to exit dialing mode. 5. Hang up using the KP9X hang-up sequence.
3. Tap PGM. 4. If the far end answers, begin your conversation. NOTE: After the far end answers, you may dial additional digits (to retrieve voice mail, log onto an automated answering system, etc.). 5. If there is no answer, or to hang up when finished talking, tap the BACK key. Hang Up displays. 6. Tap PGM to hang up. NOTE: Occasionally, you may receive intercom an intercom caller name in the call waiting window while you are talking on the phone.
CHAPTER 5 KP9X Series Keypad Programming NOTE: A summary of the keypad programming sequences is located at the back of the manual for quick reference. Keypad Programming, Display Requests Display requests let you view information about the keypanel configuration. You can display information by two methods: either by entering sequences on the programming keypad, or by scrolling the names of display requests in the call waiting window and then selecting the desired display request.
Display Listen Key Assignments FUNC DISPLAY 3 This sequence displays all listen key assignments for about 10 seconds. Lstn displays in the call waiting window. > Tap CLR to quit. Display Setup Page Assignments FUNC DISPLAY E-PNL Currently, there are four setup pages available for each keypanel. Each setup page defines a set of 16 talk and listen key assignments.
NOTE: This sequence is similar to Service Menu, Test Panel, page 44, except that the service menu test also lets you check the operation of the keypad buttons. Tone Generator Activation (FUNC-DISPLAY-7) FUNC DISPLAY 7 This sequence activates the keypanel's internal tone generator. You can use the tone generator to check the audio send and receive paths to and from the matrix. For example, you can assign a talk key on the keypanel to talk to itself.
Keypad Programming, Assigning Setup Pages 1. Tap the E-PNL key. 2. Select one of the four setup pages: tap 1, or 2, etc. 3. Tap the PGM key. 4. Tap any key in the row of keys where you want to assign the setup page. NOTE: • The same setup page cannot be assigned in more than one place. If a setup page is already assigned somewhere else, you must clear or change that assignment first.
General Procedure 1. For talk level 2 assignment only: Tap 0 2. Select the key assignment type: 0. Otherwise, skip this step. NUM Intercom port. PL Party line. AUTO Auto function. FUNC SLIST Special list. FUNC IFB FUNC ISO Camera ISO FUNC RELAY Relay or GPI output. 3.
Programming Key Assignments Using Copy There are two ways to copy key assignments: 1) you can copy a call from the call waiting window to a key; or 2) you can copy one key's assignment to another key. Copying a Call from the call waiting window to a Key 1. While the caller's name is displayed in the call waiting window, tap the COPY CW key. 2. Tap the key where you want to copy to. The name of the caller should appear in the display above the key.
NOTE: 5. In single-step mode, use the ↑↑ ↓↓ keys to make your final intercom port selection. NOTE: 6. When the keypanel is in single-step scroll mode it may take a long time to scroll to the desired name (this is particularly true of point-to-point lists). To speed up the process, you can use prefix scroll mode. Prefix scrolling mode scrolls through a list in alpha-numeric order, but displays only the first occurrence of each two-character prefix.
30
CHAPTER 6 KP-632 Menu System NOTE: A chart of the menu system is located at the back of the manual for quick reference. Menu System, Menu Access 5. Clear all names from the Call waiting display (if not clear) by tapping UP one or more times on the Call waiting key. 6. Tap MENU to activate the menu system. 7. Press ↓↓ to scroll forward through the list of menus. Press ↑↑ to scroll back. 8. Tap FWD or PGM to enter a menu. Tap BACK to exit a menu. 9.
Display Menu, Chans On Displays an alpha list, in the call waiting window, of all intercom ports that currently have talk crosspoints closed to this keypanel. Chans On is typically used to locate an open mic or other open audio source that needs to be shut off. The most likely cause is typically a talk key that has been left on at some keypanel. In this case, use the ↓↓ and ↑↑ keys to scroll through the list of names.
Menu System, Key Assign Menu Use this menu to assign intercom keys, to adjust listen levels for point-to-point keys and party line keys, and to assign setup pages. General Procedure to use the Key Assign Menu 1. Clear the call waiting window if necessary, by tapping UP one or more times on the Call waiting key. 2. Tap Menu. 3. Tap ↓↓ to scroll down to the Key Assign menu. 4. Tap PGM or FWD to enter the menu. NOTE: If you do not have a trunking intercom system, skip to step 6. 5.
10. 11. 12. 13. Tap PGM or FWD to select a list. In some cases Wait may display while the requested list is uploaded from the intercom system. When the requested list is displayed, press ↓↓ or ↑↑, to locate the desired assignment. Tap PGM or FWD to select the assignment. Tlk Lvl 1should now display in the call waiting window. Press ↓↓ or ↑↑ if necessary to select a different option. Options are as follows: Talk Lvl 1: Assigns only talk level 1. Leaves the listen assignment as is.
Key Assign Menu, IFB By default, all IFBs are restricted and you will see Not Avail when you attempt to select this item. To see IFBs, you must check the appropriate Scroll Enable check boxes in AZedit. Key Assign Menu, Spcl List Assigns a key that talks and/or listens to a special list. The key will have no effect until members have been assigned to the special list in AZedit. Note that some or all special list members may be non-keypanel devices that cannot themselves activate talk and listen paths.
4. Tap an intercom key to assign the selected auto function. OR Tap up to assign all auto functions except All Call or DIM. OR Tap down for All Call or DIM. If the assignment is successful, the abbreviation for the auto function will appear in the alphanumeric display for that key. However, if you try to assign an auto function to a key that already has that auto function assigned, the assignment will be ignored.
Clear Page Clear a page assignment from the KP-632 or EKP-632. 3. Tap PGM. Tap Key displays. 4. Tap any key in the row where you want to assign the setup page. The key assignments for that page should appear in the displays. 6 You can press ↓↓ or ↑↑ to select and assign another setup page. Or, tap CLR to exit. NOTE: You do not need to run Save Cfg to store changes to setup pages. These are stored in the intercom system.
Key Option Menu, Key Groups You can set up a key group, so that when you activate one key (the master key) all keys in the group will activate. Up to 4 key groups can be set up. 1. Select Key Groups, then tap PGM. Group 1 displays. To select a different group, press ↓↓ or ↑↑. 2. Tap PGM. Tap Master displays. The master key is the key you press to activate the group. 3. Tap the intercom key you want to use as the master. Both LEDs next to the key will light red.
Removing the solo key option To remove the solo key option, do the following: 1. Select Solo, and then tap PGM. The LEDs for the solo key will be lit red. 2. Tap the solo key to turn off the LEDs. 3. Tap CLR to exit. The solo key is now cleared. 4. Run Service Menu, Save Cfg, to save the change. RVON Conn. Menu The RVON Conn. menu is used to select an RVON connection to use with the keypanel.
Service Menu, Baud Rate 1. Select Baud Rate, then tap PGM. Auto Baud displays. To select the baud rate, press ↓↓ . Available selections are, Auto Baud, 9600 Baud, or 76.8 Baud. 2. Tap PGM to select the baud rate. 3. Tap CLR to exit when finished. The new baud rate is now set. 4. Run Service Menu, Save Cfg. to store the Baud Rate settings. Service Menu, Dim This item causes the speaker or headphone level to diminish by a specified amount whenever a talk key is activated. 1.
Filtering Filtering lets you add a 9.6 kHz notch filter to one or more audio sources. This can be useful in a few cases when the keypanel data port signal is being heard in the audio line due to cable routing problems. 1. Select Filtering, and then tap PGM. Microphone displays. Press ↓↓ or ↑↑ to display any of the following items: Microphone Matrix Aux 1 Aux 2 2. 3. Tap PGM. ♦None displays to indicates no filtering is selected. Press ↓↓. Notch displays. 4. Press PGM. ♦ Notch displays.
3. Tap PGM. The Vol. bar graph is now monitoring the selected audio source. 4. Tap CLR to exit metering, or allow the metering function to timeout after about 1 minute. Mixing Mixing lets you route selected audio signals to the intercom system, to the speaker, or to the left or right headphone when using a headset. By default, the microphone signal is routed to the matrix, and the matrix signal is routed to the speaker and to the left and right headphones. 1. Tap PGM. To Matrix displays.
3. 4. Tap PGM. Value: X displays, where X is a number between 5 and 100. To change the selection, press ↓↓ or ↑↑. The higher the number, the brighter the backlight. 5. Tap PGM. 6. Tap CLR to exit. 7. Run Service Menu, Save Cfg, to store the new setting. Service Menu, LCP-632 (GPI Option Only) By default, each LCP-632 that you connect to the KP-632 takes control of level adjustment for the first available group of 16 physical keys that it finds.
3. Press ↓↓ or ↑↑ to display a different GPI Input. 4. Tap PGM to select a GPI Input. 5. Press ↓↓ to select the talk key. 6. Tap PGM. Tap Key displays. 7. Tap the intercom key you want to assign. This key activates when the GPI input activates. 8. Tap CLR to exit, or BACK to back up and make more assignments. 9. Run Service Menu, Save Cfg, to store local GPIO settings. Assigning an Input to Activate a Key Group 1. Select Local GPIO, and then tap PGM. Input displays. 2. Tap PGM.
6. Tap an intercom key to add or remove the GPI output assignment. 7. Tap CLR to exit, or BACK to back up and make more assignments. 8. Run Service Menu, Save Cfg, to store local GPIO settings. Service Menu, Matrix Out This menu item allows the user to select between Normal or Hot Mic. In the Normal (default) setting audio from the Mic goes out to the Matrix when the talk key is latched. In the Hot Mic setting audio from the Mic goes out to the Matrix with out regard to the talk key’s state. 1.
> Select Mod Assign, and then tap PGM. Cancel? displays. To exit the procedure without making changes, tap PGM. All of the alphanumeric displays, except Mod 1, appear as shown in FIGURE 10. Assign the Mod IDs as shown in the figure. Repeat the procedure for each module. FIGURE 10. NOTE: Mod ID assignments for the KP-632 and EKP-632 You do not need to run Save Cfg after changing Mod assignments.
5. Run Service Menu, Save Cfg, to store the Preamp Out settings. Service Menu, Reset Cfg Reset Cfg restores all custom settings to the defaults and erases all stored autodial numbers. Service Menu, RVON Setup (RVON Option Only) RVON Setup is used to configure the IP Address, Netmask Address, and Gateway Address for the RVON device you want to use. To configure the RVON device on the keypanel, do the following: 1. Select RVON Setup, then tap PGM. IP Address appears. 2. Tap PGM.
Service Menu, Sidetone Sidetone lets you adjust the level of you own voice heard in the headphones when using a headset. Most people prefer some amount of sidetone to overcome the muffled sensation when talking, especially when wearing a full-muff headset. The maximum level is 0dB. Service Menu, Snoop Tally Snoop Tallies provide an indication to keypanel users that somebody is listening to them. NOTE: To use Snoop Tallies, the keypanel must be woring in Hot Mic (USM) Mode.
CHAPTER 7 Specifications Microphone Preamplifier Panel Mic (Electret) Input Level:......................................................................................................... -42dB, 150 Ohms @ 1kHz Headset Mic (Dynamic) Input Level: ................................................................................................ -50dBm, 150 Ohms@ 1kHz Output Level (to matrix): ......................................................................................................................
Speaker Amplifier and Speaker Maximum Voltage Gain: ........................................................................................................................................................ 25dB Frequency Response:................................................................................................................................ 100Hz to 10kHz, ± 2dB Output Power (per amplifier): ......................................................................................................
Connectors (Other connector options available) Panel Microphone Connector (Electret) Type: 3-circuit, 1/4” phone jack w/threaded metal bushing, compatible w/ RTS MCP5/6 Pin-out: Tip: +Audio and DC bias Ring: Common Sleeve: Chassis ground Headset Connector (Dynamic) Type: XLR5 female Pin-out: Pin 1: Mic low Pin 2: Mic high Pin 3: Common Pin 4: Headphone left high Pin 5: Headphone right high Power Input Connector Type: 5-pin locking DIN Pin-out: Pin1: Common Pin2: Common Pin3: +5VDC, 1.50A Max.
Intercom Connectors: Parallel-wired DE9S and RJ12 Connectors Type: DE9S Pin-out: Pin 1: Data + Pin 2: Data Pin 3: Audio in (from matrix) shield Pin 4: Audio out (to matrix) + Pin 5: Audio out (to matrix) Pin 6: Data shield Pin 7: Audio in (from matrix) Pin 8: Audio in (from matrix) + Pin 9: Audio out (to matrix) shield Type: RJ12 Pin-out: Pin 1: Data Pin 2: Audio in (from matrix) + Pin 3: Audio out (to matrix) + Pin 4: Audio out (to matrix) Pin 5: Audio in (from matrix) Pin 6: Data + Expansion Connector T
Type: 3-pin female XLR Pin-out: Pin 1: Ground Pin 2: Input + Pin 3: Input - Aux 2 In (Auxiliary program input 2) Type:3-pin female XLR Pin-out: Pin 1: Ground Pin 2: Input + Pin 3: Input NOTE: Balanced input, +8dBu nominal Relay 1 & 2 Out Type:9-pin male D-Sub Pin-out: Pin 1: NC contact 1 Pin 2: COM contact 1 Pin 3: NO contact 1 Pin 4: NC contact 2 Pin 5: COM contact 2 Pin 6: NO contact 2 Pin 7: +5 VDC Pin 8: Ground Pin 9: +5 VDC 53
Relay 3 & 4 Out Type: 9-pin male D-Sub Pin-out: Pin 1: NC contact 3 Pin 2: COM contact 3 Pin 3: NO contact 3 Pin 4: NC contact 4 Pin 5: COM contact 4 Pin 6: NO contact 4 Pin 7: +5 VDC Pin 8: Ground Pin 9: +5 VDC NOTE: The relay 1 and 2 contacts are electrically separate, but operate in unison. The relay 3 and 4 contacts are electrically separate, but operate in unison. The +5 VDC pins are connected internally through 1K resistors to +5 VDC and can source 5 mA.
OC 1 & 2 Out (J2) Type: 9-pin male D-Sub Pin-out: Pin 1: Gnd OC1 Pin 2: Emitter OC1 Pin 3: Collector OC1 Pin 4: Gnd OC2 Pin 5: Emitter OC2 Pin 6: Collector OC2 Pin 7: 5 VDC Pin 8: No connection Pin 9: 5 VDC Headset (External headset connector) Type:9-pin male D-Sub Pin-out: Pin 1: Gnd Pin 2: N/A leave unconnected Pin 3: N/A leave unconnected Pin 4: N/A leave unconnected Pin 5: Balanced dynamic mic input + Pin 6: Gnd Pin 7: Headset Listen Out Left Pin 8: Headset Listen Out Right Pin 9: Balanced dynamic mic i
Foot Switch/Speaker Type: 9-pin male D-Sub Pin-out: Pin 1: Gnd Pin 2: Speaker Minus (-) Pin 3: Gnd Pin 4: No connection Pin 5: Foot Switch Pin 6: Speaker Plus (+) Pin 7: No connection Pin 8: No connection Pin 9: Gnd NOTE: A switch contact closure from the footswitch input to ground will activate the footswitch input. MIC In (J7) Balanced Microphone Output Type: 3-pin female XLR Pin 1: Shield (circuit common) Pin 2: DC bias and Audio Plus (+) Pin 3: GND NOTE: Input level -42.5dBu nominal.
CHAPTER 8 KP9X Keypad Sequence Quick Reference KP9x Display Sequences FUNC DISPLAY 0. Diagnostics mode. FUNC DISPLAY 1. Display port number. FUNC DISPLAY 2. Display level 2 talk assignments. FUNC DISPLAY 3. Display listen assignments. FUNC DISPLAY -8 Display setup page assignments. FUNC DISPLAY ↓↓ or ↑↑ to select items as follows: ID PGM: Display the calculated port number. CLR to end. Lev2 PGM: Display level 2 talk assignments. CLR to end. Lstn PGM: Display listen assignments.
KP9x Setup Page Assignment 1. Tap E-PNL. 2. Select a setup page: tap 1, or 2, etc. 3. Tap PGM. 4. Tap any key in top row to assign page to top row. OR Tap any key in bottom row to assign page to bottom row. Key Assignments Using Keypad Numeric Entry 1. For talk level 2 assignment only: Tap 0 0. 2. Select the key assignment type: NUM Intercom port. PL Party line. AUTO Auto function. FUNC SLIST Special list. FUNC IFB IFB FUNC ISO Camera ISO FUNC RELAY Relay or GPI output. 3.
KP9x Phone Operation KP9X Hang-up Sequence 1. Turn OFF the TIF talk key. 2. On the keypad, tap PHONE-CLR. 3. Turn the TIF talk key ON, then OFF. The TIF key talk and listen indicators will turn off and the TIF OFF LED activates. KP9X Dial Sequence 1. Activate the TIF listen key (listen LED green). 2. Make sure the TIF talk key is OFF (Talk LED off). 3. On the keypad, tap CLR-PHONE-PGM. 4. Activate the TIF talk key (talk LED turns green).
Dialing an Autodial Number Stored in the TIF 1. Tap the PHONE key to activate dialing mode. 60 2. Tap down on the TIF talk key to latch it in the on position. 3. Tap CLR followed by the autodial number (01, 02, etc.). 4. When finished dialing, click the PHONE key again to exit dialing mode. 5. Hang up using theKP9X hang-up sequence.
CHAPTER 9 KP-632 Menu System Quick Reference Menu Access 1. Clear all names from the Call waiting display (if not clear) by tapping up one or more times on the call waiting key. 2. Tap MENU to activate the menu system. 3. Press ↓↓ to scroll forward through the list of menus. OR Press ↑↑ to scroll back. 4. Tap FWD or PGM to enter a menu. OR Tap BACK to exit a menu. 5. Within a menu: • • • Press ↓↓ or ↑↑ to scroll. Tap FWD or PGM to select an item.
Menu List Display Menu Asgn Type Chans ON Key Groups Key List Level 2 Listen Matrix Panel ID Version Key Assign Menu Pt-to-Pt Party Line IFB Spcl List Sys Relay Camera ISO UPL IFSL Auto Func Key Gain Reset Vols Setup Page Key Options Menu Auto Diala Chime1 Key Groups1 Solo1 RVON Conn. list of RVON Offers1 a. Run Save Cfg (see “Service Menu, Save Cfg” on page 47) to save these settings. 62 Service Menu Aux Inputs Baud Rate Caller Vol.
CHAPTER 10 Mode 2 Operation Section 2 Switch 4: Call Flash Timeout* When the switch is closed the menu and indefinite talking is disabled. Switch 5: Footswitch Enable / Disable* Amber talk LEDs indicate a latched talk key. Section 3 LED Indications for Intercom Keys Talk LED Indications The talk LED is the lower LED for each key. The talk LED indications are as follows: Continuous Red* Talk is on and the keypanel operator can be heard at the destination.
NOTE: The red in-use indication for TIF keys can be disabled in AZedit: In the AZedit Options menu, select Intercom Configuration, then click on the Options tab. Place a check mark next to Don't Generate Tallies for Tif And Trunk Use. Be sure to send the change to the intercom system. Note that this will also disable the flashing alpha display when talking to remote IFBs or ISOs as previously described.
CHAPTER 11 Glossary All Call - For talk key assignment only. Activating an All Call key will also activate all talk keys to the left of the All Call key (up to, but not including another All Call key). Alpha - Alphas are the user-changeable names which identify destinations (intercom ports, party lines, etc.). Change Alpha names for intercom ports using the Port Alpha button in AZedit. Change Alpha names for everything else using the Other Alpha button.
with the IFB talent, AND the IFB keys are frequently reassigned during the course of a program to talk to new talent locations. Using AZedit, several IFBs can be set up in advance, and their Listen Sources can also be defined during setup. Then every time an IFB talk key is reassigned on a keypanel, the Listen Source for each new IFB will automatically become the listen key assignment for that key. For further information about Auto Tables, Listen Sources, and IFBs, see the AZedit User Manual.
IFB - IFB (Interrupt Foldback) is a special type of communication in which a listener at a particular intercom output port normally hears an audio program source connected to a particular intercom input port. A keypanel operator can activate a key to interrupt the audio program source and then talk to the listener. Normal operation resumes when the keypanel operator releases the key.IFB is typically used to cue on-the-air talent.
Port - The ports are the individual channels that devices are connected to. Devices include: • • • 2-way communication devices, such as keypanels, belt packs etc. Audio sources, such as broadcast feeds or background music Miscellaneous audio output devices, such as powered loudspeakers, PA systems etc. Communication between Ports (Point-to-Point, or P-P) The audio signal from any input port can be routed to any output port.
Special List - A special list is a means for a keypanel operator to talk and/or listen to several unrelated destinations using a single key. Special lists are useful for group call or zone paging. Special list members are defined in the intercom configuration software. Once a special list has been configured, it can be assigned to a keypanel key.A special list is a group of intercom ports that a keypanel operator can talk or listen to by activating a single key.
70
Appendix A RVON-1 General Description of the RVON-1 Voice Over Network Card Installed directly into KP-32 family or KP 812 keypanels, the RVON-1 provides voice over IP (Internet Protocol) communications, for the RTS ADAM Intercom family. In general, voice over IP means sending voice information in digital form using discrete packets rather than the traditional hardwire connection. The RVON-1 delivers an integrated solution for connecting keypanels to the Intercom matrix over standard IP networks.
Specifications DIGITAL Compression Audio Bit Rate Coding Delay Playout Delay IP Bandwidth G.711 64k 125μs 20-60ms 160-224 kbps G.729A 8k 10ms 20-120ms 32-112kbps G.723 5.3k/6.3k 30ms 60-120ms 29-45kbps Data depends on CODEC selection. NOTE: The Playout Delay and Bandwidth depend on the configured amount of audio per packet. CONNECTIONS • RJ-45 Ethernet via backcard • 14-pin KP Compatible Expansion Connector Pin 1...........................................................................
Default Addresses for the RVON Product Line TABLE 2. Default Addresses for the RVON Product Line Product Default IP Address Default Subnet Mask RVON-I/O 192.168.0.1 255.255.0.0 RVON-8 192.168.0.2 255.255.0.0 RVON-1 192.168.0.3 255.255.0.0 RVON-C 192.168.0.4 255.255.0.0 RVON-16 192.168.0.5 255.255.0.0 GPIO-16 192.168.0.6 255.255.0.0 MCII-e 192.168.0.7 255.255.0.0 Cronus 192.168.0.8 255.255.0.0 Zeus III 192.168.0.9 255.255.0.
Firmware Compatibility Requirements for the RVON-1 Card Description Master Controller 9.19.0 or later Peripheral Controller 10.10.0 or later DBX 1.10.1 or later AZedit 2.06.06 or later RVON-8 1.1.0 or later KP-32 2.0.0 or later TABLE 3. Compatibility 74 Version Requirements for the RVON-1 card.
Installation of the RVON-1 Card in a KP 812 To install the RVON-1 card, do the following: 1. Remove the cover from the KP 812 keypanel. NOTE: FIGURE 11. 2. It is recommended to seat the RVON-1 card on the J2 connector located on the KP 812 motherboard before snapping the RVON-1 board onto the spacers. Be careful to attach J2 to J37 correctly. Spacer placement on KP 812 motherboard Gently secure the RVON-1 board in place.
In the KP 812, the RVON-1 card connects to the KP 812 by way of the J2 connector on the RVON, attached to J37 on the KP 812 header. RJ-45 J37 FIGURE 13. 3. The J37 connector on the KP 812 board. Connect the RJ-45 extension connector cable to the RVON-1 board. RVON-1 Relay When connected to an Ethernet LAN, audio comes from the RVON-1 card; and, when Ethernet is not plugged in, the audio comes from the AIO connection. Note, the user does not need to remove the RVON-1 to switch to AIO mode.
Configure the RVON-1 from the KP 812 Top Level Menu, Service, Rvon Setup Set the IP Address from the Service Level Menu The RVON-1 card, when shipped has a default IP Address already configured. This must be changed in order for the RVON-1 card to function properly because the pre-configured IP Address may not work with you network. To set the IP Address, do the following: 1. On the KP 812, scroll to Menu. The top level menu appears. 2. Turning the encoder knob, scroll to Service. 3.
17. Enter the first number in the Gateway IP Address. This activates the first octet of the Gateway IP Address and clears the rest of the address. 18. Tap the encoder knob. This confirms the first octet in the Gateway IP Address and moves you to the second octet. NOTE: Press PGM to skip over any octet that does not need modifications. 19. Repeat steps 19 and 20 until the entire Gateway is entered. 20. Tap the encoder knob. 21. Press and hold the encoder knob to exit the menu.
Configure the RVON-8 using AZedit to contact the RVON-1 To configure the RVON-1 card, do the following in AZedit: 1. From the Status menu, select I/O Cards. The I/O Card Status screen appears showing the types of installed. 2. Right click on an RVON-8 card, and then select RVON-8 Configuration. The RVON-8 Configuration screen appears. NOTE: The RVON-8 you use should be already configured. If it is not configured, refer to your RVON-8 Card User Manual.
NOTE: 10. VAD saves network bandwidth by stopping the flow of audio packets when silence is detected. VAD is similar to VOX. Once you are completely finished, click Apply. Download RVON-1 Firmware Through AZedit NOTE: AZedit sends firmware directly to the RVON-1 card over Ethernet. This is different from other I/O cards (except the RVON-8) that receive the firmware from the Master Controller.
6. Click Open. The Download Device Firmware screen appears. 7. Click Begin Download. The download begins. 8. Click OK. The RVON-1 firmware download is complete. This takes a minute or two to occur. WARNING: 9. Do NOT power down the keypanel until you have verified the new version information from AZedit. If the card loses power while reprogramming the onboard flash memory, the card may become unbootable and may need to have its flash chips reprogrammed at the factory.
virtual private network, is one such security measure to protect the intelligence of the LAN. A computer outside the LAN must have an address or key known by the VPN to allow access to the LAN. Many companies use a VPN to connect two different LANs, thus allowing the transfer of data between two networks. LAN (local area network) vs.
Wide Area Network A WAN (Wide Area Network) connects two or more LANs and can span a relatively large geographical area. For example, Telex Headquarters in Burnsville, MN is connected to several branch offices in Nebraska and Arkansas over a WAN. The largest WAN in existence is the Internet. FIGURE 15. Wide Area Network Diagram Accessing The Wide Area Network (WAN) Figure 14 shows LAN IP Addresses using a common IP Address, 10.2.100.X (192.168.X.X is another common address).
Network Address Translation (NAT) Using the initial IP Address, then converting it to a valid WAN IP Address is how the network address translation works, in theory. Once the IP address is changed, it is up to the network interface device (such as a router, gateway, switch, etc.) to keep track of which computers are talking on which ports.
. TABLE 6. Well-Known TABLE 6.
IP Addresses If you do not know your IP Address, you can open a DOS screen in a Windows-based environment and bring up the ipconfig screen. To find your IP Address using ipconfig, do the following: 1. From the Start Menu, open a Command Prompt screen. 2. At the prompt, type ipconfig, then press Enter. The IP configurations appear for your machine, such as the DNS suffix, IP Address, Subnet Mask, and Default Gateway. 3. At the prompt, type Exit to close the screen.
Ping a Computer Pinging a computer on the network makes sure it is able to be “seen” and receive messages on the network. NOTE: You can also ping your RVON-8 card to verify that it is responding over the network by putting the cards IP Address in place of the computer IP Address. To Ping a computer on the network, do the following: 1. 2. From the Start menu, select Run.... At the Run command, type CMD to open a Command Prompt screen. 3.
Possible Pitfall With Routers, Gateways, And Switches Anytime computers communicate through routers, gateways, and switches, they may be allowed or denied the connection. Network interface devices can be configured to block specific outgoing requests, as well as incoming requests, based on the IP Address and/or port. This is one of the security mechanisms of a router. This also happens when broadcast messages are sent and received.
RVON Configuration RVON cards use ports for communication of audio and control packets. Because routers can be configured to block certain incoming and outgoing requests, you will need to open the following ports in your network to allow WAN connections to and from a Network Interface Device. See Table 7 on page 89 for the ports that need to be opened for the RVON cards to operate properly. TABLE 7. Ports Port necessary for RVON card functionality.
Network Terminology Bridges A bridge is a device that connects two LANs, or two segments of the same LAN that use the same protocol. Sometimes called “transparent bridges, they work at the OSI model Layer 2. Simply put, they are not concerned with protocols. Their main job is to pass data to a destination address that is predetermined in the data packet. With a bridge, all of your computers are on the same network subnet (see Subnet).
CLASS A - supports 16 million hosts on each of 127 networks. CLASS B - supports 65,000 hosts on each of 16,000 networks. CLASS C - supports 254 hosts on each of 2 million networks. LAN A LAN is a computer network that connects a relatively small area (a single building or group of buildings). Most LANs connect work stations and computers to each other.
RVON Serial and Telnet Commands RVON card programming can be done via direct serial or telnet connection. There are several physical connections to an RVON board: • Direct serial through custom debug cable (J20 6-pin bottom front) The customer debug cable always functions as the general-purpose debug tool. • Backcard DB-9 J2 The backcard DB-(must be disabled/enabled via a DIP Switch because it can also be used for serial port passthrough.
3. Press Enter. The RVON logon screen appears. 4. In the logon field, type the RVON logon (default = telex). Press Enter. In the password field, type the RVON password (default = password). Press Enter. A prompt appears. Type dbgcmd to access the debug command screens. 5. 6. 7. 8. Press Enter. An MXP prompt appears. 10. At the prompt, type Show. 9.
11. Press Enter. The show commands screen and MXP prompt appears. 12. At the MXP prompt, type the show command you want to see (for example, “show rvon”). Press Enter. The values for the RVON-1 card appear. 13.
To edit the RVON-1 configuration, do the following: 1. Repeat steps 1 through 9 from above. 2. At the MXP prompt, type either set RVON or set EMAC (see screen descriptions below). 3. Press Enter.
set channel dest_ip Allows you edit the destination IP Address the RVON-1 card will communicate with set channel dest_type Allows you to edit the destination type for the device the RVON-1 card will talk with set channel dest_channel Allows you to edit the destination channel of the device the RVON-1 will talk with set channel channel_codec Allows you to edit the CODEC to be used for transferring the data between the two devices set channel input_gain Allows you to edit the input gain for the RVON-
Notes 97
