User Manual

ManualsBrandsRSI VIDEOTECHNOLOGIES ManualsElectronicsOutdoor Motion Viewer

The OMVC 201/601/702 MotionViewer is a wireless, battery

operated, motion activated outdoor camera designed for use in

Videofied

security systems.

• Powered by 4 Lithium batteries for extended battery life.

• Lens for vertical curtain detection - Detection pattern : 80cm width

and up to 12m distance.

• 4 infrared LEDs for 12m night vision.

• Standard detection distance (up to 12 meters).

• Fully weatherproof (IP65) and temperature resistant

(-20°C/+60°C).

• Tilt sensor tamper.

• Transmits check-in/status signal every 8 minutes.

Product Summary

Installation Guidelines

For easier installation, programming and RF testing should be done to check for

good communication between the control panel and all system devices before

mounting system devices.

Install the detector and other system devices in the order of the following steps:

Programming/RF Testing - program detector and all other devices into the

control panel and test RF communication from each intended device location to

the control panel.

Mounting - mount detector at the tested location.

Mounting

Use proper tools and hardware.

Mount camera between 2.5 m to 4 m height.

The OMV MotionViewer detection distance may vary depending on weather

and the detector mounting (height, tilt). The OMV is not suitable to protect an

area, it needs to be used to protect the perimetry of an installation.

Mount detector aimed toward the spot to protect.

In order to reduce false alarms, do not aim the detector toward vegetation, a

road, or unlimited space.

Do not cover the Fresnel lens. Use only the provided masking kit to block

detection towards specific spots (trees, bushes, etc.).

MB110 Mounting kit for

Outdoor MotionViewer

DOC. - REF. 213-OMVC

VERSION : JULY 2015

INSTALL SHEET

OMVC OUTDOOR MOTION VIEWER

Summary of content (4 pages)

PAGE 1
OMVC OUTDOOR MOTION VIEWER INSTALL SHEET DOC. - REF. 213-OMVC VERSION : JULY 2015 Product Summary The OMVC 201/601/702 MotionViewer is a wireless, battery operated, motion activated outdoor camera designed for use in Videofied ® security systems. • Powered by 4 Lithium batteries for extended battery life. • Lens for vertical curtain detection - Detection pattern : 80cm width and up to 12m distance. • 4 infrared LEDs for 12m night vision. • Standard detection distance (up to 12 meters).
PAGE 2
INSTALL SHEET OMVC OUTDOOR MOTION VIEWER Programming/RF Testing/Mounting The following provides summarized steps for device programming, testing, and mounting. For complete details, refer to the control panel installation manual. 1 Separate the base from the box 2 Install 3 3.6V LS14500 SAFT batteries observing correct polarity. 3 Put control panel into Programming/Configuration mode. a programmed 4 Using alphanumeric keypad, proceed through menus until the display shows ADD A NEW DEVICE.
PAGE 3
OMVC OUTDOOR MOTION VIEWER INSTALL SHEET Security notes / (FR) Notes de sécurité / (DE) Hinweise zur Sicherheit English Français Deutsch • Remove the batteries before any maintenance ! • WARNING, there is a risk of explosion if a battery is replaced by an improper model ! • Observe polarity when setting up the batteries! • Do not litter the batteries when they are used! Dispose of it properly according to Lithium Metal requirements • Retirez les piles avant toute opération de maintenance ! • Attention
PAGE 4
OMVC OUTDOOR MOTION VIEWER INSTALL SHEET ELECTRICAL PROPERTIES W, XL, XT, XV and their variants Panel compatibility Power requirements Type C - 4 Lithium batteries 3,6 V LS14500 Battery life Detection lens 2 years Tamper detection Tilt RADIO PROPERTIES Spread spectrum bidirectionnal Operating frequency • 868MHz - OMVC 201 (Europe, Africa, Asia) • 915 MHz - OMVC 601 (USA, Canada, South America) • 920 MHz - OMVC 702 (Australia, South America) Weight Operating temperature Max.