User Manual

ManualsBrandsRSI VIDEOTECHNOLOGIES ManualsElectronicsIndoor Contact Transmitter

Installation guidelines

For easier installation, programming and RF testing should be

done to check proper communication between the control

panel and all system devices before mounting system devices.

Install the detector and other system devices in the following

order:

Programming/RF Testing - program the relay and all other

devices into the control panel and test RF communication from

each intended device location to the control panel.

Mounting - Mount the relay at the tested location.

The IRT indoor relay transmitter is designed

for use with Videoﬁed™ wireless security

systems.

The contact includes the following features :

• Completely wireless and powered by a

Lithium battery

• Dual tamper function provides detection

for both wall and cover tamper

• Transmits check-in/status signal every 8

minutes

• Programmable radio output for wired

devices trigger

Product presentation

Programming/RF Testing/Mounting

The following provides summarized steps for device

programming, testing and mounting. For complete details,

refer to the control panel installation manual.

Loosen the screw, open the box and

insert the batteries.

2 Close the box and tighten the screw.

3 Access to the panel configuration

menu.

Proceed through menus until the

display shows ADD A NEW DEVICE.

Press YES/OK. The display shows

PRESS PROGRAM BUTTON OF DEVICE.

Using a paperclip, press and release

the relay INIT button.

The contact LED flashes. Wait for the

keypad to display TRANSMITTER (1-24)

RECORDED.

Press YES/OK. The display shows

RADIO RANGE TEST?

Press YES/OK again. The IRT LED starts

flashing and keypad display shows TEST

IN PROGRESS.

8 Take the transmitter to its intended

mounting location and make sure that

the LED flashes continuously, indicating

good communication with the control

panel.

9 Press YES/OK to end the radio range test then press ESC

NO.

10 The display shows NAME + LOCATION:

Enter appropriate device name/location (up to 16 characters),

then press YES/OK. The display shows the device number and

name for confirmation.

The display shows ENTERING A NEW DEVICE?

Repeat steps 1 - 14 for remaining devices.

Screw

LED

INIT button

INSTALLATION SHEET

DOC. - REF. 219-IRT

MODIF. DATE : NOVEMBER 2016

VERSION : 08.XX.XX

INDOOR RELAY TRANSMITTER IRT200 IRT601 IRT702

Summary of content (4 pages)

PAGE 1
INSTALLATION SHEET INDOOR RELAY TRANSMITTER IRT200 IRT601 IRT702 DOC. - REF. 219-IRT MODIF. DATE : NOVEMBER 2016 VERSION : 08.XX.XX Product presentation Installation guidelines The IRT indoor relay transmitter is designed for use with Videofied™ wireless security systems.
PAGE 2
INSTALLATION SHEET INDOOR RELAY TRANSMITTER IRT200 IRT601 IRT702 1 Remove the base from the contact. 2 Hold the base against the wall and mark the mounting points. 3 Drill. 4 Mount the base on the wall. Mounting brackets 5 Connect 2 AWG22 wires from the devices to trigger (sirens, flashes, cameras, smoke generators, garage doors, etc.) to the input terminals. Connect to the 6 wired devices to trigger Mount the IRT on its base and lock with the screw.
PAGE 3
INSTALLATION SHEET INDOOR RELAY TRANSMITTER IRT200 IRT601 IRT702 Security notes / (FR) Notes de sécurité / (DE) Hinweise zur Sicherheit English Français Deutsch • Remove the batteries before any maintenance ! • WARNING, there is a risk of explosion if a battery is replaced by an improper model ! • Observe polarity when setting up the batteries! • Do not litter the batteries when they are used! Dispose of them properly according to Lithium Metal requirements • Retirez les piles avant toute opération de
PAGE 4
INSTALLATION SHEET INDOOR RELAY TRANSMITTER IRT200 IRT601 IRT702 ELECTRICAL PROPERTIES Panel compatibility BOX W panels Type C - CR123A - Lithium battery Battery Nominal voltage 3V Low battery limit 2.