MODEL 2023/2017 ACTORY CA VERSION 1.0 R.P.S. Corporation P.O. Box 368 Racine, Wisconsin 53401 Phone: 1-800-634-4060 Fax: 1-866-901-3335 www.factorycat.
HOW TO USE THIS MANUAL This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The SAFETY section contains important information regarding hazard or unsafe practices of the machine. Levels of hazards are identified that could result in product or personal injury, or severe injury resulting in death. The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering the correct replacement parts.
TABLE OF CONTENTS PARTS BREAKDOWN ILLUSTRATION MACHINE INFORMATION FORM WARRANTY REGISTRATION FORM MACHINE SPECIFICATIONS COMMON WEAR PARTS SAFETY MESSAGES !!SAFETY PRECAUTIONS!! MACHINE CONTROLS AND FEATURES MACHINE SETUP ADJUSTING & REMOVING SQUEEGEE INSTALLING PAD DRIVER OR BRUSH OPERATION ADJ. SOLUTION FLOW & SHROUD CURTAIN ADJ. PAD ASSIST DRIVE, DRAIN & CLEAN TANKS TIP TANK, RAISE & LOWER SQUEEGEE ADJ.
R.P.S. CORPORATION P.O. BOX 368 RACINE, WI 53401 PHONE: 800-634-4060 FAX 866-901-3335 WWW.FACTORYCAT.
MACHINE SPECIFICATIONS 2017 2023 Poly (3/8 thick) 3/16 Steel (2) 10 x 2 (2) 4 x 2 42 x 18 x 40 26 334 lbs Poly (3/8 thick) 3/16 Steel (2) 10 x 2 (2) 4 x 2 48 x 18 x 40 32 406 lbs Standard Brush Motor (Power / Speed): Brush Down Pressure: 2017-17: (1) 17 2017-20: (1) 20 (1) 0.75 hp / 200 rpm 0 125 pounds 2023-20: (1) 20 2023-23: (1) 23 (1) 0.
COMMON WEAR PARTS ITEM BRUSH TYPE BRUSHES SUPER-GRIT TOUGH-GRIT MIDI-GRIT LIGHT-GRIT POLY (.028) NYLON (.
SAFETY MESSAGES YOUR SAFETY, AND THE SAFETY OF OTHERS, IS VERY IMPORTANT, AND OPERATING THIS UNIT SAFELY IS AN IMPORTANT RESPONSIBILITY. TO HELP YOU MAKE INFORMED DECISIONS ABOUT SAFETY, WE HAVE PROVIDED OPERATING PROCEDURES AND OTHER SAFETY INFORMATION IN THE MANUAL. THIS INFORMATION INFORMS YOU OF POTENTIAL HAZARDS THAT COULD HURT YOU OR OTHERS. IT IS NOT PRACTICAL OR POSSIBLE TO WARN YOU OF ALL THE HAZARDS ASSOCIATED WITH OPERATING THIS UNIT. YOU MUST USE YOUR OWN GOOD JUDGEMENT.
!! SAFETY PRECAUTIONS!! WARNING: ALWAYS USE THE CHARGER PROVIDED WARNING: HAZARDOUS VOLTAGE. SHOCK, BURNS EXPLOSION OR FIRE CAN RESULT. KEEP SPARKS AND OPEN FLAMES AWAY. BY THE MAUFACURER TO CHARGE THE MACHINE. IT IS AN AUTOMATIC CHARGER, SPECIFICALLY DESIGNED TO CHARGE AT THE APPROPRIATE RATE. IF YOU MUST USE A DIFFERENT CHARGER, DISCONNECT THE BATTERIES BEFORE CHARGING. THIS WILL PREVENT DAMAGE TO THE ELECTRONIC SPEED CONTROLLER.
MACHINE CONTROLS AND FEATURES 2 1 4 3 8 9 13 10 14 11 12 15 FIGURE 1. 6 5 7 FIGURE 2. 16 27 29 17 26 30 19 31 32 25 24 20 21 FIGURE 3. 22 23 PAGE 7 33 34 35 36 37 38 FIGURE 4.
CONTROLS AND FUNCTIONS SEE FIGURES (1-4) ON PAGE 7 SEE FIGURE 1 1. 2. 3. 4. 5. 6. 7. MAIN POWER SWITCH: TURNS THE MACHINE ON AND OFF. VACUUM SWITCH: TURNS VACUUM MOTOR ON. SOLUTION SWITCH: OPENS AND CLOSES SOLUTION VALVE. SCRUB DECK SWITCH: RAISES AND LOWERS SCRUB DECK (PROVIDES AJDUSTMENT +/- FOR PRESSURE). BATTERY GAUGE: INDICATES AMOUNT OF BATTERY CHARGE . POWER LIGHT (GREEN): INDICATES POWER "ON". DOWN PRESSURE GAUGE: INDICATES AMOUNT OF PAD/BRUSH PRESSURE. SEE FIGURE 2 8.
MACHINE SETUP UNCRATING MACHINE ATTACHING SQUEEGEE CAREFULLY CHECK THE CRATE FOR ANY SIGNS OF DAMAGE AND THAT THE BATTERIES ARE IN THE UNIT. 1. LOWER THE SQUEEGEE MOUNTING PLATE BY ROTATING THE LIFT LEVER COUNTER-CLOCKWISE. (SEE FIGURE 6.) TO UNCRATE THE MACHINE, REMOVE BANDING FROM AROUND THE CRATE. TAKE OFF THE TOP AND SIDES AND DISPOSE OF PROPERLY. REMOVE BRACKETS (A) FROM MACHINE WHEELS. REMOVE BOLTS (B) FROM PALLET THEN REMOVE BOARD (C). CAREFULLY ROLL THE MACHINE OFF OF THE BASE.
ADJUSTING SQUEEGEE 1. TURNING ADJUSTMENT KNOB CLOCK-WISE (TIGHTENING) WILL RAISE TIPS & LOWER CENTER. (SEE PICTURE BELOW) REMOVING SQUEEGEE 1. WITH THE SQUEEGEE IN THE UP POSITION, TURN MACHINE POWER OFF. 2. DISCONNECT VACUUM HOSE FROM SQUEEGEE AND LOOSEN BOTH KNOBS. (SEE PICTURE BELOW) 3. PULL SQUEEGEE ASSEMBLY REARWARD FROM THE LIFTING CARRIER. 4. INSPECT OR REPAIR AS NEEDED AND REINSTALL. 2. THIS SQUEEGEE IS ADJUSTED TOO FAR BACK AND WILL NOT PICK UP ON THE CORNERS. *NOTE TIPS OFF THE FLOOR.
INSTALLING PAD DRIVER OR BRUSH 1. 2. 3. 6. TURN ON MACHINE POWER. RAISE THE SCRUB DECK BY DEPRESSING THE BRUSH SWITCH (-) TO THE UP AND OFF POSITION AND TURN MACHINE POWER BACK OFF. THE MACHINE IS EQUIPPED WITH A SHROUD. UNSCREW THE TWO KNOBS ON TOP OF THE SCRUB DECK AND REMOVE THE SHROUD. (SEE FIGURE 9.) FIGURE 11. FIGURE 9. 4. 5. ATTACH BRUSHES OR PADS TO MOTOR HUBS. SQUEEZE THE SCISSOR LOCKING DEVICE AND LIFT BRUSH UP ON TO THE MOTOR DRIVE HUB.
OPERATION PRE-CLEANING CHECK LIST OPERATING HINTS READ AND UNDERSTAND THE SAFETY SECTION ON PAGES 5 AND 6 BEFORE OPERATING THE MACHINE. 1. OBSERVE THE AMOUNT OF SOLUTION THE MACHINE IS DISPENSING ON THE FLOOR AND ADJUST TO THE DESIRED FLOW. TO INCREASE THE SOLUTION FLOW RATE, ROTATE THE SOLUTION CONTROL KNOB. TO SHUT THE SOLUTION OFF COMPLETELY, USE THE SWITCH, OR JUST RELEASE THE DRIVE BUTTON. 1. CHECK BATTERY CONDITION GAUGE ON THE CONTROL PANEL. MAKE SURE BATTERIES ARE FULLY CHARGED BEFORE USING. 2.
ONE PASS SCRUBBING SCRUB ONLY (SEE FIGURE'S 13 & 14.) (SEE FIGURE 14.) 1. TURN ON MACHINE POWER SWITCH "A" , MAKE SURE THE "PAD ASSIST" ADJUSTMENT KNOB IS A LOW SETTING. 1. TURN ON MACHINE POWER SWITCH "A", MAKE SURE THE "PAD ASSIST" ADJUSTMENT KNOB IS A LOW SETTING. 2. LOWER SQUEEGEE BY ROTATING THE LIFT LEVER "B" COUNTER-CLOCKWISE. 2. LOWER SCRUB HEAD TO THE FLOOR, USE THE TOP HALF (+) OF THE BRUSH SWITCH "C" . 3. LOWER SCRUB HEAD TO THE FLOOR, USE THE TOP HALF (+) OF THE BRUSH SWITCH "C" . 4.
ADJUST SOLUTION FLOW DRAINING SOLUTION TANK 1. TURN SOLUTION VALVE ADJUSTMENT LEVER (A) CLOCK-WISE TO INCREASE SOLUTION FLOW, COUNTER-CLOCKWISE TO DECREASE SOLUTION FLOW. (SEE FIGURE 15.) TO DRAIN LEFT OVER CLEANING SOLUTION FROM THE SOLUTION TANK, PERFORM THE FOLLOWING STEPS. (SEE FIGURE 18.) A 1. PULL THE CLEAR SIGHT TUBE/DRAIN HOSE OFF BARBED ELBOW. 2. RINSE OUT TANK AND SOLUTION FLOW SYSTEM WITH CLEAN WATER. FIGURE 15. ADJUST SHROUD CURTAIN 1.
OPEN RECOVERY LID 1. RELEASE BOTH LATCHES ON RECOVERY TANK LID. (SEE FIGURE 20.) 2. ROTATE LID FULLY OPEN. CLEAN "DRAIN SAVER" WITH RECOVERY LID OPEN & TANK FULLY DRAINED 1. REMOVE 2" SQUEEGEE INTAKE HOSE FROM "DRAIN SAVER" STRAINER. (SEE FIGURE 23.) 2. REMOVE STAINLESS SCREEN, DISPOSE OF DEBRIS. 3. RINSE SCREEN WITH FRESH WATER FROM THE OUTSIDE TO THE INSIDE HOLDING SCREEN UPSIDE DOWN. THIS WILL ALLOW FOR BETTER CLEANING. 4. REPLACE THE SCREEN INTO THE BRACKET. 5.
SQUEEGEE UP TIP TANK 1. FULLY DRAIN SOLUTION TANK. 1. PLACE BOTH HANDS ON THE HANDLE BAR. 2. FULLY DRAIN RECOVERY TANK. 2. USE RIGHT FOOT TO PRESS DOWN ON SQUEEGEE LIFT POST (YELLOW SLEEVE). (SEE FIGURE 28.) 3. PRESS DOWN COMPLETELY AND SQUEEGEE WILL LOCK INTO "UP" POSITION. 3. TO REMOVE TANK BOLTS, USE 3/16" ALLEN WRENCH "A" PROVIDED WITH MACHINE, LOCATED ON SIDE OF SCRUBDECK LIFTING BRACKET. (SEE FIGURE 25.) 4. REMOVE BOLTS ON SIDES OF TANK. (SEE FIGURE 26.) 5. REMOVE SQUEEGEE. 6.
DECK HEIGHT ADJUSTMENT 1. SOLUTION FILTER TO ADJUST DECK HEIGHT FOR BRUSH CLEARANCE, TURN ADJUSTMENT BOLT "A" CLOCK-WISE TO RAISE DECK, COUNTER-CLOCKWISE TO LOWER DECK. (SEE FIGURE 33.) FIGURE 33. 1. THE SOLUTION SYSTEM HAS A "INLINE FILTER" (A) TO FILTER OUT CLEANING SOLUTION PRIOR TO SCRUBBING. (SEE FIGURE 35.) FIGURE 35. A VAC MOTOR CLEANING SOLUTION FILTER (SEE FIGURE 34.) 1. THE MACHINE IS EQUIPPED WITH A 24 VOLT, 3HP, VAC MOTOR (A). 2.
BATTERY CHARGING CAUTION: THE FOLLOWING INSTRUCTIONS ARE INTENDED FOR THE 24V CHARGER SUPPLIED WITH THE MACHINE. DO NOT USE ANY OTHER CHARGER WITH THIS MACHINE. CHARGER SPECIFICATIONS * OUTPUT VOLTAGE OF 24 VOLTS. * OUTPUT CURRENT OF 18 AMPS MAX. * INPUT VOLTAGE OF 110 VOLTS/60 HZ. * AUTOMATIC SHUT OFF CIRCUIT. * MADE FOR DEEP CYCLE BATTERIES. FIGURE 30. DANGER: ALWAYS CHARGE BATTERIES IN A WELL VENTILATED AREA. BATTERIES EMIT HYDROGEN GAS. EXPLOSION OR FIRE CAN RESULT.
MAINTENANCE DAILY MAINTENANCE MONTHLY MAINTENANCE 1. REMOVE AND CLEAN PADS OR BRUSHES. NEVER USE SOILED PADS WHEN CLEANING. REPLACE PADS WHEN THEY BECOME PACKED WITH RESIDUE. 1. CHECK SCRUB HEAD AND SQUEEGEE LIFTING CABLES FOR WEAR AND SPRING TENSION. 2. REMOVE AND CLEAN DEBRIS FROM THE FLOAT SHUT-OFF SCREEN LOCATED INSIDE THE RECOVERY TANK. 2. CHECK MACHINE FOR WATER LEAKS AND LOOSE NUTS AND BOLTS. 3. CHECK TO SEE IF BATTERY CABELS ARE TIGHTENED (TIGHTEN IF NEEDED) 4. CHECK PARKING BREAKE 5.
PREVENTATIVE MAINTENANCE RECORDS USE THIS FORM TO MAKE COPIES FOR YOUR INTERNAL RECORDS PREVENTATIVE MAINTENANCE CHECKED NOTE ROTATE BRUSHES DRAIN SOLUTION TANK FLUSH SOLUTION SYSTEM CLEAN SOLUTION SCREEN DRAIN RECOVERY TANK FLUSH RECOVERY TANK CLEAN VACUUM SCREEN ROTATE REAR SQUEEGEE BLADE CHECK BATTERY WATER LEVEL CHECK BATTERY VOLTAGE CHECK CHARGER CONDITION CHECK BATTERY CONNECTIONS CHECK CHEMICAL LEVEL CHECK MACHINE PERFORMANCE SCRUBBING POWER VACUUM POWER CONTROLS WATER ON TURNS GAUGES AND CONTROL
PREVENTATIVE MAINTENANCE RECORDS USE THIS FORM TO MAKE COPIES FOR YOUR INTERNAL RECORDS PREVENTATIVE MAINTENANCE CHECKED NOTE ROTATE BRUSHES DRAIN SOLUTION TANK FLUSH SOLUTION SYSTEM CLEAN SOLUTION SCREEN DRAIN RECOVERY TANK FLUSH RECOVERY TANK CLEAN VACUUM SCREEN ROTATE REAR SQUEEGEE BLADE CHECK BATTERY WATER LEVEL CHECK BATTERY VOLTAGE CHECK CHARGER CONDITION CHECK BATTERY CONNECTIONS CHECK CHEMICAL LEVEL CHECK MACHINE PERFORMANCE SCRUBBING POWER VACUUM POWER CONTROLS WATER ON TURNS GAUGES AND CONTROL
TROUBLE SHOOTING PROBLEM CAUSE SOLUTION NO POWER, NOTHING OPERATES FAULTY POWER SWITCH BATTERIES NEED CHARGING FAULTY BATTERY LOOSE BATTERY CABLE MAIN CIRCUIT BREAKER TRIPPED CONTACT LOCAL SERVICING DEALER SEE CHARGING BATTERIES REPLACE BATTERY TIGHTEN LOOSE CABLE WAIT 5 MINUTES FOR AUTO RESET DETERMINE CAUSE AND CORRECT BRUSH MOTOR(S) DO NOT OPERATE GREEN BUTTON IS NOT DEPRESSED 30 AMP CIRCUIT BREAKER TRIPPED DEPRESS BUTTON ON HANDLE BAR RESET & REDUCE PRESSURE DETERMINE CAUSE AND CORRECT CONTACT
TROUBLE SHOOTING PROBLEM CAUSE SOLUTION NO SOLUTION FLOW NO SOLUTION IN TANK SOLUTION SWITCH OFF SOLUTION SCREEN CLOGGED FAULTY SOLUTION SOLENOID FAULTY SOLUTION SWITCH FILL SOLUTION TANK TURN SOLUTION SWITCH ON REMOVE AND CLEAN SCREEN CONTACT LOCAL SERVICING DEALER CONTACT LOCAL SERVICING DEALER POOR WATER RECOVERY RECOVERY TANK IS FULL BALL/SCREEN IS CLOGGED VACUUM HOSE IS CLOGGED SQUEEGEE IS CLOGGED SQUEEGEE BLADE IS WORN FAULTY VACUUM HOSE VACUUM MOTOR GASKET TORN TANK GASKET FAULTY DRAIN PLUG L
MODEL 2023/2017 SERIES MACHINE PARTS SECTION
ACTUATOR LIFT ASSEMBLY 11 4 1 8 5 7 12 6 9 7 3 9 7 6 2 PAGE 23 10
ACTUATOR LIFT ASSEMBLY Item Part Number Part Description Qty 1 190-1150 ACTUATOR ARM 1 2 190-1155 ACTUATOR ANCHOR 1 3 21-6000 DOWN PRESSURE SPRING 2 4 290-1233 3/8" ID, 1/2" OD, 1/4" LG BEARING 2 5 H-01219 HCS 3/8"- 24 X 1 1/8" SS 1 6 H-70005 HCS 1/4"- 20 X 1" SS 4 7 H-70710 HN 1/4"- 20 SS 6 8 H-70732 HN 3/8"- 24 SS 1 9 H-71063 LW 1/4" SS 4 10 H-NJ04C JNYL 1/4" - 20 SS 2 11 H-RUE14 3/8" RUE RING COTTER 1 12 H-ZCP170 CLEVIS PIN 3/8" x 2.
SQUEEGEE TRAIL ARM ASSEMBLY 18 17 1 16 17 8 12 16 2 12 10 2 5 11 18 8 17 16 3 7 12 9 12 9 6 9 10 4 13 14 13 PAGE 25 15
SQUEEGEE TRAIL ARM ASSEMBLY Item Part Number Part Description Qty 1 10055418 5/16-18 X 5-1/2" DOUBLE ENDED STUD S/S 1 2 190-1055 TUBE, 5/16" ID X 7/16" OD X 1-5/8" LG 2 3 190-7140 SQUEEGEE SWING PLATE 1 4 190-7150 SQUEEGEE TRAIL ARM 1 5 21-7205 STAR KNOB 1 6 21-7240 SPRING, 1/2" ID X 1-3/4" LG 1 7 21-7610 SQUEEGEE TRIANGLE PLATE 1 8 390-7712 COMPRESSION SPRING 2 9 4-446 GROMMET-3/8 ID X 1-1/2 OD X .
AXLE SUPPORT ASSEMBLY 7 2 5 7 6 8 9 4 9 11 10 1 NOTE: LEAVE JAM NYLOK NUT ITEM #11 AT END OF BOLT THREADS ITEM #9. SPRINGS FROM TRAIL ARM ASSEMBLY WILL GO BETWEEN THE TWO NUTS.
AXLE SUPPORT ASSEMBLY Item Part Number Part Description Qty 1 190-1020 AXLE SUPPORT 1 2 190-1170 AXLE 1 3 190-6175 DRIVE TIRE 8" x 2" (GREY) 2 4 290-1233 3/8" ID, 1/2" OD, 1/4" LG BEARING 2 5 H-00222 FW 3/4 X 1 1/8 X 3/32 SS 4 6 H-25435 SSS CP 5/16" X 1/4" 2 7 H-33376 SET SCREW SHAFT COLLAR, 3/4" ID X 9/16 LG 2 8 H-68015 SNAPRING 3/4" 4 9 H-70055 HCS 5/16"- 18 X 1" SS 2 10 H-70711 HN 5/16"- 18 SS 2 11 H-NJ05C JNYL 5/16"- 18 SS 2 PAGE 28
SQUEEGEE SUSPENSION NOTE: ATTACH SPRINGS BETWEEN NUTS ITEMS 10 & 11 ON AXLE SUPPORT ASSEMBLY.
SQUEEGEE SUSPENSION Item Part Number Part Description Qty 1 H-70105 HCS 3/8"- 16 X 1" SS 2 2 H-71017 FW 3/8" X 7/8" SS 4 3 H-NJ06C JNYL 3/8- 16 SS 2 4 N/A AXLE SUPPORT ASSEMBLY 1 5 N/A SQUEEGEE TRAIL ARM ASSEMBLY 1 PAGE 30
2023 FRAME FRONT 4 6 10 15 12 3 7 11 12 11 7 5 13 9 13 2 7 7 11 14 11 9 2 8 ACTUATOR LIFT ASSEMBLY 1 PAGE 31
2023 FRAME FRONT Item Part Number Part Description Qty 1 190-1000 MAINFRAME 1 2 190-8283 RELAY, 24V, 50 AMP 2 3 290-2815 CIR. BREAKER - 15A, 24V 1 4 H-01201 GROMMET 2 5 H-0129155 JNYL #10-32, 18-8 S/S 2 6 H-375HCN HCN 3/8"- 16 2 7 H-70710 HN 1/4"- 20 SS 8 8 H-70861 NYLOK 5/16" - 18 SS 3 9 H-71013 FNW 1/4" X 5/8" SS 4 10 H-71059 LW #10, SS 2 11 H-71063 LW 1/4" SS 8 12 H-72563 RPH #10-32 X 1/2" SS 4 13 H-74420 CB 1/4"- 20 X 1.
2023 FRAME MIDDLE 9 2 9 9 9 1 14 14 14 9 14 9 14 12 3 14 14 7 4 6 7 CONNECT ITEM 7 (HOSE) FROM TANK OUTSIDE PAGE TO THIS END OF INLINE FILTER. CONNECT THIS END OF ITEM 4 (HOSE) TO DELTROL VALVE ON DECK ASSEMBLY.
2023 FRAME MIDDLE Item Part Number Part Description Qty 1 190-1000 MAINFRAME 1 2 190-1005 FRAME SUPPORT - LH 1 3 190-1006 FRAME SUPPORT - RH 1 4 190-1271 CLEAR TUBE, WIRE REINF.
2023 FRAME REAR 21 7 3 21 20 12 4 17 14 8 9 13 6 11 18 1 19 15 10 8 2 16 5 17 18 PAGE 35
2023 FRAME REAR Item Part Number Part Description Qty 1 190-1000 MAINFRAME 1 2 190-1280 1" ID x 3" LG RUBBER COVER - YELLOW 1 3 190-1350 SQUEEGEE LIFT CABLE 1 4 190-7100 SQUEEGEE PIVOT PLATE 1 5 22-9812 3/8-16 X 1.0" OD X 3.0" LG STANDOFF 1 6 290-1248 FW BRONZE .500 ID X 1.00 OD X .
SCRUB DECK WHEEL ASS'Y 1 6 4 8 5 3 7 PAGE 37 2
SCRUB DECK WHEEL ASS'Y Item Part Number Part Description Qty 1 190-1030 DECK WHEEL PIVOT BRACKET 1 2 190-1035 DECK WHEEL PIVOT SUPPORT 1 3 190-3020 4.0" WHEEL (RED) 1 4 290-1233 3/8" ID, 1/2" OD, 1/4" LG BEARING 2 5 H-70112 HCS 3/8"- 16 X 2-1/4" SS 1 6 H-NJ06C JNYL 3/8- 16 SS 1 7 H-RUE14 3/8" RUE RING COTTER 1 8 H-ZCP170 CLEVIS PIN 3/8" x 2.
20" DISK DECK ASSEMBLY 11 16 16 29 10 16 8 24 24 16 14 29 10 9 14 16 24 24 10 24 24 16 14 1 24 25 16 12 11 10 24 24 16 14 32 29 31 15 21 1 25 18 31 7 9 6 17 30 4 23 3 28 27 5 22 26 2 20 PAGE 39 9 26 19 13 28
20" DISK DECK ASSEMBLY Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Part Number 190-1115 190-1120 190-1142 190-1145 190-1166 190-4500 190-7240 190-9586 21-7205 290-1247 5-124 7-222 H-10055 H-33080 H-4796 H-5012 H-53425 H-70001 H-70105 H-70136 H-70710 H-70858 H-70860 H-70861 H-71017 H-71067 H-71614 H-74429 H-74432 H-9307 H-NJ05C N/A Keywords 20" LIFT BRACKET 20" DISK DECK 20" DECK CURTAIN BAND CLEAR TUBE, 1/2" ID X 1.0" OD X 1.
20" SHROUD ASSEMBLY 13 5 12 9 8 1 8 9 7 10 10 7 2 11 6 3 4 PAGE 41
20" SHROUD ASSEMBLY Item Part Number Part Description Qty 1 190-1101 20" FRONT SHROUD 1 2 190-1140 20" & 23" SHROUD CURTAIN BAND 1 3 190-1141 20" SHROUD CURTAIN BAND 1 4 190-1165 20" SHROUD CURTAIN, FRONT 1 5 190-3030 4.
23" DISK DECK ASSEMBLY 11 16 16 29 10 16 8 24 24 16 14 29 10 1 31 9 14 16 24 24 10 24 24 16 14 24 25 16 12 11 10 24 24 16 14 32 29 31 15 21 1 25 18 31 7 9 6 17 30 3 23 4 28 27 5 22 26 2 20 PAGE 43 9 26 19 13 28
23" DISK DECK ASSEMBLY Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Part Number 190-1110 190-1125 190-1145 190-1152 190-1176 190-4500 190-7240 190-9586 21-7205 290-1247 5-124 7-222 H-10055 H-33080 H-4796 H-5012 H-53425 H-70001 H-70105 H-70136 H-70710 H-70858 H-70860 H-70861 H-71017 H-71067 H-71614 H-74429 H-74432 H-9307 H-NJ05C N/A Keywords 23" LIFT BRACKET 23.0" DISK DECK CLEAR TUBE, 1/2" ID X 1.0" OD X 1.
23" SHROUD ASSEMBLY 13 5 12 9 8 1 8 9 7 10 10 2 7 3 4 11 PAGE 45 6
23" SHROUD ASSEMBLY Item Part Number Part Description Qty 1 190-1105 23" FRONT SHROUD 1 2 190-1140 20" & 23" SHROUD CURTAIN BAND 1 3 190-1151 23" CURTAIN BAND 1 4 190-1175 SHROUD CURTAIN, FRONT 1 5 190-3030 4.
DISK DECK BRUSH ASSEMBLY 14 14 15 11 1 4 17 2 8 9 6 12 5 7 16 3 10 13 PAGE 47
DISK DECK BRUSH ASSEMBLY Item Part Number 1 21-5000 2 32-3044 3 40-423 4 5-431A 5 H-29048 6 H-70055 7 H-71013 8 H-71017 9 H-71067 10 SEE COMMON WEAR PARTS 11 40-423 12 40-433 13 40-433 14 H-29048 15 H-71013 16 SEE COMMON WEAR PARTS 17 SEE COMMON WEAR PARTS Part Description BRUSH DRIVER FW .75 ID X 1.13 OD X .
VAC MOTOR ASSEMBLY 4 5 2 3 3 11 9 9 8 6 1 7 PAGE 49 12 10
VAC MOTOR ASSEMBLY Item Part Number Part Description Qty 1 190-1225 1.
2023 TANK INSIDE 20 8 20 15 21 19 12 18 13 18 17 14 1 18 4 8 17 8 9 3 8 2 17 16 11 15 7 5 6 VAC MOTOR ASSEMBLY 10 PAGE 51
2023 TANK INSIDE Item 1 Part Number 190-1025 Part Description 1-1/2" ID X 18" LG WIRE REINF BLACK HOSE Qty 1 2 190-1130 BAFFLE 1 3 190-1180 SOLUTION FILL LID 1 4 190-1190 SOLUTION FILL LID GASKET 1 5 6 190-1210 190-1215 2.0" MNPT X 2.0" BARB, NYLON 2.0" MNPT X 1.50" BARB, NYLON 1 1 7 190-1220 SCREEN 1 8 190-1272 2.0" ID X 24.
2023 TANK OUTSIDE 22 16 16 14 22 6 20 10 2 7 17 17 19 21 19 21 13 12 5 8 18 17 19 18 3 21 4 NOTE: CONNECT ITEM 3 TO INLINE FILTER SEE FRAME MIDDLE PAGE 11 9 PAGE 53 15 1
2023 TANK OUTSIDE Item Part Number Part Description Qty 1 190-1205 ELBOW, 90 DEG, 2.0" MALE NPT X 2.0" BARB 1 2 190-1210 2.0" MNPT X 2.0" BARB, NYLON 1 3 190-1270 1/2" ID X 11" LG WIRE REINF. CLEAR HOSE 1 4 190-1300 1-1/2" ID X 31" LG WIRE REINF BLACK HOSE 1 5 190-1370 CLEAR HOSE, 3/4" ID X 1.
TANK LID ASSEMBLY 4 2 3 11 9 10 7 8 5 6 12 10 PAGE 55 1
TANK LID ASSEMBLY Item Part Number Part Number Model 2023 Model 2017 Part Description Qty TANK LID GASKET 1 TANK CLEAR COVER GASKET 1 TANK LID 1 1 190-1070 170-1070 2 190-1075 3 190-1400 4 190-1410 VAC FORMED CLEAR COVER 1 5 21-4060 LANYARD 1 6 32-8000 8" CONTINUOUS HINGE 2 7 H-37015 NYLOK #10-32 1 8 H-37708 1/4-20 LC ACORN NUT 8 9 H-71059 LW #10, SS 1 10 H-71889 SMS #14 x 1/2" S/S 6 11 H-73448 SHCS #10-32 X 1/2" S/S 1 12 H-73752 BHSCS 1/4-20 X 1/2" 8 170
CONTROL PANEL 21 16 26 10 16 25 2 16 22 1 22 20 25 4 13 3 5 9 12 11 17 14 15 19 7 6 18 8 PAGE 57
CONTROL PANEL Item Part Number 1 190-1090 2 190-1501 3 190-2310 4 190-3851 5 190-5431 6 190-8370 7 290-9609 8 4-101 9 4-234 10 5-233 11 5-300 12 5-301 13 5-302 14 5-892 15 7-837 16 8-231 17 8-235 18 8-262 19 H-01199 20 H-01201 21 H-0129155 22 H-28878 23* H-70888 24* H-70889 25 H-72976 26 H-85981 27* H-85985 Part Description CONTROL PANEL 2023 CONTROL PANEL DECAL POWER (GREEN) DOWN PRESSURE GAUGE BATTERY GAUGE FUSE RESETTABLE 25 AMP FUSE, RESETTABLE, 30 AMP SERIAL NUMBER PLATE KEY SWITCH MOM-OFF-MOM DPDT EM
HANDLE BAR 6 8 10 10 9 9 5 "SINGLE" PUSH BUTTON OPTION 1 4 4 2 3 7 "DUEL" PUSH BUTTON OPTION 16 20 18 20 19 16 19 20 15 13 19 15 18 20 19 14 14 11 17 12 PAGE 59
HANDLE BAR "SINGLE" PUSH BUTTON OPTION Item Part Number Part Description Qty 1 190-1040 HANDLE BAR 1 2 190-1041 RED WIRE, 16 GAGE 1 3 190-1042 YELLOW WIRE, 16 GAGE 1 4 190-1390 END CAP 2 5 7-228 SWITCH MOUNT PLATE 1 6 7-229 PUSH BUTTON SWITCH 1 7 H-03124 1/4" ID, 3/8" OD, 3/8" LG FLANGED BEARING, NYLON 1 8 H-108 HEAT SHRINK 2 9 H-71059 LW #10, SS 2 10 H-72398 PPHMS #8-32 X 1/2" SS 2 "DUEL" PUSH BUTTON OPTION Item Part Number Part Description Qty 11 190-1041
32 INCH SQUEEGEE ASSEMBLY 20 22 23 21 20 24 1 25 2 24 25 19 2 15 15 15 3 4 18 5 15 6 15 7 25 16 15 8 17 15 15 10 10 11 9 9 10 14 10 13 11 12 7 8 PAGE 61 USE RED LOCKTITE ON STUD INTO SQUEEGEE BODY
32 INCH SQUEEGEE ASSEMBLY Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Part Number H-70065 H-71015 21-7600 H-33371 H-70711 H-71065 22-755G 23-7170 H-00288 H-00249 H-72555 23-7181 22-754G 23-7160 H-70908 5-846 H-00568 290-5786 H-NJ04C H-00283 21-7570 H-0172248 21-7220 H-70005 H-71063 Part Description HCS 5/16"- 18 X 3" SS FW 5/16" X 3/4" SAE SS SIDE WHEEL (GREY) 5/16" ID SHAFT COLLAR HN 5/16"- 18 SS LW 5/16" SS FRONT SQUEEGEE BLADE SQUEEGEE BAND, FRONT PPH #10-32 X 2 1/2" SS PPH #
FRAME, SUSPENSION & SQUEEGEE 7 5 1 3 6 2 4 8 PAGE 63
FRAME, SUSPENSION & SQUEEGEE Item Part Number Part Description Qty 1 H-70710 HN 1/4"- 20 SS 4 2 H-70861 NYLOK 5/16" - 18 SS 5 3 H-71063 LW 1/4" SS 4 4 H-74620 1/4-20 X 3/4" U-BOLT 2 5 H-75661 FPH 5/16"- 18 X 1" SS 5 6 N/A 32 INCH SQUEEGEE ASSEMBLY 1 7 N/A MODEL 2023 FRAME ASSEMBLY 1 8 N/A SQUEEGEE SUSPENSION ASSEMBLY 1 PAGE 64
FRAME & SCRUB DECK 12 1 10 1 7 6 2 6 9 6 3 6 5 8 2 8 5 11 4 9 13 PAGE 65
FRAME & SCRUB DECK Item Part Number 1 290-1247 2 390-7712 3 H-63917 4 H-70112 5 H-70711 6 H-70861 7 H-71015 8 H-71016 9 H-74431 10 H-74432 11 H-NJ06C 12 N/A 13 N/A Part Description FW BRONZE .50" ID X 1.0" OD X .062 COMPRESSION SPRING SLEEVE, .50 OD X .375 ID X 1.
FRAME, BATTERIES, TANK, TANK LID, CONTROL PANEL, HANDLE BAR 5 7 9 3 4 8 1 6 2 PAGE 67
FRAME, BATTERIES, TANK, TANK LID, CONTROL PANEL, HANDLE BAR Item Part Number Part Description Qty 1 190-1095 2 X 4 X 13-1/2" LG 1 2 190-2110 BATTERY, 12 V, 140 AH, 230 RC 1 3 H-71016 FW 5/16" X 7/8" SS 1 4 H-73541 SHCS 3/8"- 16 X 1 1/4" SS 1 5 N/A MODEL 2023 TANK LID ASSEMBLY 1 6 N/A MODEL 2023 FRAME ASSEMBLY 1 7 N/A MODEL 2023 HANDLE BAR ASSEMBLY 1 8 N/A MODEL 2023 TANK ASSEMBLY 1 9 N/A CONTROL PANEL ASSEMBLY 1 PAGE 68
