RoyalTek GPS Speed Camera Warning Device RCD-1000 Offline version Users Manual English 1
Content 1.Product Introduction .........................................................................................................................3 1.1 Overview................................................................................................................................3 1.2 Check the Package Content....................................................................................................3 1.3 Install RCD-1000 in your vehicle ................................................
1.Product Introduction 1.1 Overview The Device is equipped with the latest generation SiRF Star III digital processor specially designed for fast and accurate fix on GPS signals. It had been designed to help you drive safety within the confines of today’s speed limits, by alerting you quickly and easily to the presence of Police speed traps, often located at Accident black spots, electronically indicating potentially dangerous and hazardous situations.
1.3 Install RCD-1000 in your vehicle (D) Speed Limit button (E) POI Button (C) Volume Control (A) Mini USB Port (B) External Antenna Port z Place the Dashboard Pad on your dashboard as close to the windscreen as possible in clear view of the driver’s line of sight. z Place your RCD-1000 device on the dashboard pad, which is designed to hold it firmly in place. z Now connect the USB cable to the cigar lighter adapter provided and insert the other end to socket (A).
2.Specification 2.1 Specification GPS GPS Chipset Frequency Channel C/A Code Chipset TTFF (Open SKY,typical) Accuracy - Sirf GSC3f/LP - L1, 1,575.42 MHz - 20 parallel - 1,023 MHz - Reacquisition: less than 1s - Hot start: less than 1s - Warm start: less than 35s - Cold start: less than 35s - Position: within 10m for 90% - Velocity: 0.
2.2 Hardware Overview (1) The POI record Button: Press for more than 2 seconds to record current position. A short beep sound and blinking LED will inform you that the POI has been successfully store. Note: The user must use the software to carry out the POI management. Note: The POI Record Button function will be enabled after GPS is fixed and the Speed Camera database was successful pre-uploaded into memory.
1 Event System Initialize 2 GPS Search 3 GPS is fixed 4 5 6 7 8 9 10 11 12 13 Memory full /Erase LED Display Green+Red (No 1+No 2+No3), Sweeping Green (No 1), Blinking Audio Alarm 1 beep Green (No 1), Glowing 2 beeps after GPS Fixed Not available for this model X Approach Fix Camera Zone and Not exceed speed pre-alert (distance less than* 1500 meter- Notification range) Red (No 2+No3) Over speed Glowing Approach Fix Camera Zone and pre-alert (distance less than *500 meter- Critical rang
3.Software Installation and Usage 3.1 Start to use “Speed Camera Detector Utility” Check the COM port of RCD-1000 first. Click “Start” Æ “Control Panel”Æ”Performance and Maintenance”Æ“System”, and you will see the System Properties dialog box; click on “Hardware” tab and then the “Device Manager” button. Expand the “Ports (COM & LPT)” item, and the “Prolific USB-to-Serial Comm Port” is the COM port of your RCD-1000. The user should connect the device first.
Figure2 Figure3 Figure 4 is shown System will download the POI points from device automatically. POI data will be erased from device after POI load process done. Figure 4 If the figure 5 dialog is shown, it means there is no POI data in the device.
Figure 5 3.2 POI Management Procedure When proceed the POI Management, system will auto create the POI folder for POI data download. Note:POI data are stored in the PC side and named POI.csv and stored in the subdirectory /POI/. User can load POI data, delete POI data or Save POI data by using the Utility. Note: ◆Load POI: User can edit the POI points by click the button ”Load POIs”. There are 5 types of status will show on the Utility screen after loading POI action is done. *Duplicated with No.
please refer to Figure 6. Figure 6 Figure 7 shows the Load POI process done. Figure 7 Figure 8 shows the Delete POIs process.
Figure 8 3.2.1 POI Management and shown on Map To display the POIs on Google Map, the Internet connection is needed. Move the mouse cursor to the required “Latitude” or “Longitude“ point column then press the mouse right key, the message “Go to Google Map” showed as Figure 9 Figure 9 3.2.2 POI data modification User can modify the speed, latitude, and longitude and add comments.
After the modification is complete, please press the button “OK” to save the modification. ◆Go to SCDB Coverage: Show the device’s speed camera database coverage on Google Map ◆Go to POI: When user clicks the “Go to POI” button, the screen will back to the POI point Map window.
Figure 8 3.3 SCDB and POI import setting ◆SCDB Setting : There is one type Camera database data. Fixed Speed Camera database data User can download the Speed Camera database from his computer (local file). For the Speed camera database file format, please reference the example: File name: *.csv Latitude, Longitude, direction, vmax, Type 46.55886,2.2,35.40,2 ◆POI Setting : Note: The function will be enabled after the Save POI action was done by user. User can integrate the POI data into SCDB database.
Figure 11 3.3.1 Download SCDB data from Local file Currently, users can upload DB data combinations are as follows: 1) Only SCDB 2) SCDB + POI 3.3.1.1 Download SCDB data from Local file If user wants to download SCDB data from user computer (local file), please check the” Download Speed Cameras from Local file.” And select the local path.
Figure12 Press the button “Go to Connection Page” and the AP will go to the “connection” page. System will show the notification message. Shows as Figure 13 and 14 Figure13 Figure14 Figure 15 shows that the upload proceed.
Figure15 Figure 16 shows that the download process is completed. And system will auto alert you to do the action ”RESRT and Reconnect the device” after the upload process was completed. Please re-connect the device. Figure16 3.3.2 POI Setting process Go to the page “SCDB and POI import setting”, user should check the checkbox “SCDB setting” to choose the SCDB at the same time, then press the button “Go to connection Page’, .The utility will go to page “Connection” and integrate SCDB automatically.
3.4 SCDB Setting Change to “SCDB Setting” menu bar ◆Speed Camera Alert Setting : User can set the Critical Range value and Notification range of the device. Note: Notification range should be bigger than Critical range 200m. Figure17 3.5 Utility Revision information Change to “About” menu bar User can get the RoyalTek SCDB Utility version.
