Royal Sovereign LAMINATORS OWNER'S MANUAL RSC-1650H/1650C PLEASE READ AND SAVE INSTRUCTIONS -1-
TABLE OF CONTENTS TOPICS INSTRUCTION PAGE --------------------------------------------------------------- 3 ------------------------------------------------------ 3 ----------------------------------------------------------- 4 --------------------------------------------------------------- 4 NAMES OF MAJOR PARTS OF MACHINE------------------------------------ 5 SETTING UP FILM ------------------------------------------------------------- 6 -------------------------------------------------------
INSTRUCTION Thank you for purchasing a Royal Sovereign Roll Laminator. It has been designed and manufactured to provide years of continuous service in the professional environment. To insure high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information. SAFETY PRECAUTIONS The safety recommendations outlined in this section are to be read, understood and followed before operating machine.
CHARACTERISTIC RS Roll Laminator Line is advanced laminators with time transcendental design, utilizing the latest in laminating technology. It is designed for you to set temperature and speed as necessary. Also you can laminate anything at high speed,regardless of thickness of material and type of film.It is also designed for convenient use by anyone through the simple procedure of adjusting film tension in accordance with the thickness of film and materials to be laminated.
NAMES OF MAJOR PARTS OF MACHINE 1 3 11 4 6 2 8 5 9 7 10 12 13 NO PART NAME 1 FRAME-GUIDE,PAPER ○ 2 TAKE-UP SWITCH ○ 3 TAKE-UP BOBBIN ○ 4 IDLE BAR ○ 5 TABLE-FRONT ○ 6 HOT ROLLER 7 ASS'Y-STAND ○ 8 CONTROL PANEL ○ 9 PRESSURE LEVER ○ 10 TENSION CONTROL KNOB ○ 11 SAFETY COVER ○ 12 FOOT SWITCH ○ 13 REMOCON SWITCH ○ RSC-1650H RSC-1650H UPPER ROLLER -5- X
주 주 름 름 L 방 방 C 지 지 D 부 부 표 시 창 열 열 판 버 판 튼 부 SETTING UP FILM COLD FILM PAPER BACK 1. Set the glossy side of upper/lower film to face the heat. ( Glossy side is PET film and matte side is thermal polymer laminating film.) 2. Like picture 1, insert core into the left side of upper/lower film shaft. 3. Like picture 2 and 3, insert core into the right side of upper/lower film. 4. Like picture 4 and 5, adhere core closely. (Make the right/left direction of fixing screw consistent.) 5.
HANGING FILM TAKE UP DEVICE COLD FILM PAPER BACK HOT ROLLER UPPER IDLE BAR PAPER BACK LOWER IDLE BAR 1. Set up cold film below the upper bar of the machine. (Set the same as methord of the HOT film for protect paper of lower part) 2. Set the pressure lever to the 15mm, open mode. 3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers. 4. Pull the film from the upper roller passing over the upper idle bar to the upper roller and put it on the upper roller. 5.
CONTROL OF ROLLER PRESSURE ***Methods of controlling pressure of the roller** 1. For setting, pull the pressure lever out and turn the lever to following the indication 2. OPEN/15mm(Board) : For laminating 15mm thick board (RSC-1650H/1650C) 3. 10~13mm(Board) : For laminating 10~13mm thick board 4. 5~7mm(Board) : For laminating 5~7mm thick board 5. 1mm(Hard Board) : For laminating 1mm thick board 6.
INSTRUCTIONS FOR CONTROL PANEL We designed this machine standing by user’s convenience. You can manipulate speed and temperature .
1. FUNCTIONS OF CONTROL PANEL 1 RUN/STOP BUTTON : Run or stop the rollers 2 SPEED BUTTON : Increase or decrease speed 3 LED OF SPEED : Display or speed 4 LED OF TEMP. : Display temperature 5 TEMP.BUTTON : Increase or decrease temperature 6 REVERSE BUTTON : To make the rollers run backward 2.HOW TO USE BUTTONS 1 RUN / STOP BUTTON Push the RUN button in order to run rollers and push STOP button to stop it.
LAMINATING STEPS 1. Put cold roll film on upper bar.(Set the same as methord of the HOT film for protect paper of lower part) 2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel clockwise. (Revolve core to make protectingpaper tight a little bit.) 3. Set pressure lever at the proper position following to your lamination condition. 4. After pressing the RUN/STOP button choose and set proper speed by using the SPEED button or . 5.
METHOD FOR USING CUTTER **Cross Cutter** 1. It is on the back side of the machine. 2. After lamination, move cutter to a point about 1/3 of the width of lamination. 3. Grasp film with one hand and press the cutter, cutter downward and slide it to the direction intending to cut with another hand. 4.Press the cutter and slide it the other way.
IMPORTANT SAFETY CONCERNS 1.Please be cautious that neck tie, necklace, long hair, clothes are kept well away while operation. 2.Prevent children from accessing the machine Extreme Heat Will Cause Injury 3.Place the machines on the plated place in order to prevent the machine from damage. 4.Make certain that the machine is connecterd to an adequate power souce. 5.Do not use any other purposes other than Lamination. MAINTENANCE 1.Do not allow the machine to run with only one roll of film installed.
It's not out of order Symptom *Rollers do not operate after press RUN button Cause 1. Power cord may not be plugged 1. Check the power cord. in. 2. Power switch is at OFF mode. 2. Check if the switch is on. 3. Emergency switch may be at 3. Check if the emergency switch ON mode. *Wrinkled lamination CHECK POINT is off. 4. The safety cover is opened. 4. Check the s/w of safety cover is right. 1. Film tension is not proper, too 1. Adjust film tension. tight.
WARRANTY 1. For six month from the date of purchase, Royal Sovereign International Corporation or its authorized service center will repair this product free of charge if it is defective in material or workmanship. 2.
