Assembly Instructions PROPANE FIRE PIT Questions, problems, or missing parts? Before returning to the store, call Royal Garden Customer Service. 866-988-3300 8 a.m. -5 p.m., PST Monday - Friday Retain this manual for future use.
Parts & Tools PART A QTY PICTURE & DESCRIPTION PART 1 J LID B 1 C 1 ROCKS (13.2LBS) QTY 1 K 1 L 20 + 1 TABLE TOP D M 2 20 + 1 PICTURE & DESCRIPTION RIGHT DOOR LEG PROPANE TANK SUPPORT BOLT (M6X12MM) FLAT WASHER SIDE PANEL E 1 SIDE PANEL WITH OPENING F 1 DOOR G 1 H 1 I 1 LEFT DOOR LEG WARNING: To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.
Assembly Step 1 Place table top(C) upside down on a flat, protected surface. Attach left door leg (G),left leg (H),right leg (I),and right door leg (J) to table top(c) with bolts (L) and flat washers(M) using Phillips head screwdriver ,not included. Do not tighten completely. Step 2 Attach side panel with opening(E) to right door leg (J) and right leg(I) with bolts (L) and flat washers(M) using Phillips head screwdriver, not included. Do not tighten completely.
Step 3 Attach side panel (D) to right leg (I) and left leg (H) with bolts (L) and flat washers (M) using Phillips head screwdriver, not included. Do not tighten completely. Attach second side panel (D) to left leg (H) and left door leg (G) with bolts (L) and flat washers (M) using Phillips head screwdriver, not included. Do not tighten completely. Step 4 Position as shown.
Step6 Position assembled unit to desired location. Adjust levelers on bottom unit the table is stable. Place rocks (B) into the fire bowl. Ensure rocks are not covering the ignition portion of the burner. Place lid (A) over the top .The lid (A) must be removed when the burner is in operation. Wait until the unit cools completely before replacing lid (A). Step7:Attaching the metal sheet and the tube rim to the base tube Place the propane tank, not included, onto the propane tank support (K).
SAFETY INFORMATION READ THE OPERATING INSTRUCTIONS BEFORE USE. THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH SUCH REGULATIONS AS ARE ENFORCED. WARNING: For outdoor use only CAUTION: Installer: Leave the manual with the user for future use. Consumer: Please keep this manual for future reference. Read the installation, operating, and maintenance instructions thoroughly before installing or servicing this gas appliance.
SAFETY INFORMATION (CONTINUED) WARNING: Use a standard 20 lb propane cylinder only. Reference the NFPA 58: Liquefied Petroleum Gas Code Manual for further guidance on Usage, Installation, Storage, etc. Use this heater only with a propane vapor withdrawal supply system. The pressure regulator and hose assembly supplied with the appliance must be used. A dented, rusted, or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier.
OPERATING (CONTINUED) WARNING: Never use this appliance for other than the intended use. DO NOT use this appliance to prepare food. Initial Lighting: When lit for the first time, the appliance emits a slight odor. This is a normal temporary condition caused by the “burn-off” of internal paints and lubricants used in the manufacturing process and does not occur again. Run the burner on high for approximately thirty minutes.
OPERATING (CONTINUED) LIGHTING INSTRUCTIONS TO LIGHT: 1. Check to make sure burner controls are in the off position. Slowly turn on the gas supply valve. 2. Press and hold electric igniter button. 3. Turn the burner control to the high position. Press and hold until the burner lights. Release the electric igniter button while still holding the bruner control knob. 4. Continue to depress the burner control knob for 30 seconds and then release. If the flame goes out, repeat the procedure. 5.
TROUBLESHOOTING PROBLEM PROBLEM CAUSE SOLUTION The flame is low when the valve is turned to high. The propane lighting Ensure lighting procedure is followed carefully. The valve must be procedure was not followed in the off position when the tank valve is turned on. Then turn the correctly. tank on slowly to allow pressure to equalize. See Lighting Instructions in the Operating section. Burners burn with yellowThere is possibly a spider Thoroughly clean the burner holes.
ONE YEAR LIMITED WARRANTY Royal Garden branded products are warranted to the original retail buyer if the furniture frames or welds fail structurally within one (1) year from the date of purchase. Royal Garden will repair or replace the part/piece at our discretion. Replacement will be in the original color and style whenever possible, however equal value replacement will be offered in the event of product discontinuance.
2 Pack Steel Lounge Chairs With Cushions Assembly Instructions Item#SENRCH203 If you have any problems with this product, (missing or damaged parts, assembly issues, etc.), Contact us directly for fastest service: customerservice@royalgarden.com Call us on our Toll-Free Customer Service Hotline: 8 a.m. -5 p.m.
2 Pack Steel Lounge Chairs With Cushions Item#SENRCH203 PART QTY A 2 B 2 C 2 D 2 PICTURE PART QTY AA 8 PICTURE ATTENTION: 1． 2. 2 To avoid damage of your new patio furniture, please use either the carton or another soft surface such as carpet to prevent product scratches during assembly. To better line up assembly points, loosely tighten bolts until the furniture is fully assembled. .Then fully tighten bolts .
2 Pack Steel Lounge Chairs With Cushions Item#SENRCH203 Step 1: Step 2: 3
- About Your New Outdoor Furniture - IMPORTANT If you have any problems with this product (missing or damaged parts, assembly issues, etc.), Contact us directly for fastest service • Email Us at: customerservice@royalgarden.
- About Your New Outdoor Furniture Our Warranty Program For a period of one (1) year after date of purchase, the Manufacturer will either repair or replace defective components in accordance with this Limited Warranty. This warranty is between the Manufacturer and the original purchaser and is valid only when accompanied by the original purchaser’s sales receipt showing original date of purchase and location of purchase.
