Project

7
Step 3: Topper and Whiteboard
3.1 – Topper Parts
Per the drawing, cut the parts from Handi Panel and
1’ X 2’ to make the topper. When cutting, make sure the
emboss portion will be hidden after assembly.
3.2 – Assemble Topper
Gluing the pieces will eliminate the need to cover any
fastener holes.
3.3 – Size the Whiteboard Panel
Cut a 12-1/2” X 24-1/2” section from the remaining
portion of the Handi Panel. Drill ¼” holes ¾” from sides
and top and place another hole ¾” from the top in the
middle of the panel.
3.4 – Mark and Drill Plastic
The easiest way to mark the clear panel hole location is
to align to desired location on the panel and trace hole
locations. Depending on the type and thickness of Lexan
or Plexiglas purchased you can ether drill or punch
(paper hole punch) the fastening holes. NOTE: Make the
hole in the clear panel slightly larger than the fastener
(1/4” minimum).
Topper Parts
Size the Panel
Assemble
Mark and Drill Plastic
Topper parts
3.1 – Topper Parts
Per the drawing, cut the parts from Handi
Panel and 1' X 2' to make the topper. When cutting,
make sure the emboss portion will be hidden after
assembly.
3.2 – Assemble Topper
Gluing the pieces will eliminate the need to
cover any fastener holes.
3.3 – Size the Whiteboard Panel
Cut a 12-1/2” X 24-1/2” section from the
remaining portion of the Handi Panel.
Drill ¼” holes ¾” from sides and top and place
another hole ¾” from the top in the middle of the
panel.
3.4 – Mark and Drill Plastic
The easiest way to mark the clear panel hole
location is to align to desired location on the panel
and trace hole locations. Depending on the type and
thickness of Lexan or Plexiglas purchased you can
ether drill or punch (paper hole punch) the fastening
holes.
NOTE: Make the hole in the clear panel slightly
larger than the fastener (1/4” minimum).
Step 3 Topper and
whiteboard
Assemble
Size the panel
Mark and drill Plastic
Topper parts
3.1 – Topper Parts
Per the drawing, cut the parts from Handi
Panel and 1' X 2' to make the topper. When cutting,
make sure the emboss portion will be hidden after
assembly.
3.2 – Assemble Topper
Gluing the pieces will eliminate the need to
cover any fastener holes.
3.3 – Size the Whiteboard Panel
Cut a 12-1/2” X 24-1/2” section from the
remaining portion of the Handi Panel.
Drill ¼” holes ¾” from sides and top and place
another hole ¾” from the top in the middle of the
panel.
3.4 – Mark and Drill Plastic
The easiest way to mark the clear panel hole
location is to align to desired location on the panel
and trace hole locations. Depending on the type and
thickness of Lexan or Plexiglas purchased you can
ether drill or punch (paper hole punch) the fastening
holes.
NOTE: Make the hole in the clear panel slightly
larger than the fastener (1/4” minimum).
Step 3 Topper and
whiteboard
Assemble
Size the panel
Mark and drill Plastic
Topper parts
3.1 – Topper Parts
Per the drawing, cut the parts from Handi
Panel and 1' X 2' to make the topper. When cutting,
make sure the emboss portion will be hidden after
assembly.
3.2 – Assemble Topper
Gluing the pieces will eliminate the need to
cover any fastener holes.
3.3 – Size the Whiteboard Panel
Cut a 12-1/2” X 24-1/2” section from the
remaining portion of the Handi Panel.
Drill ¼” holes ¾” from sides and top and place
another hole ¾” from the top in the middle of the
panel.
3.4 – Mark and Drill Plastic
The easiest way to mark the clear panel hole
location is to align to desired location on the panel
and trace hole locations. Depending on the type and
thickness of Lexan or Plexiglas purchased you can
ether drill or punch (paper hole punch) the fastening
holes.
NOTE: Make the hole in the clear panel slightly
larger than the fastener (1/4” minimum).
Step 3 Topper and
whiteboard
Assemble
Size the panel
Mark and drill Plastic
Topper parts
3.1 – Topper Parts
Per the drawing, cut the parts from Handi
Panel and 1' X 2' to make the topper. When cutting,
make sure the emboss portion will be hidden after
assembly.
3.2 – Assemble Topper
Gluing the pieces will eliminate the need to
cover any fastener holes.
3.3 – Size the Whiteboard Panel
Cut a 12-1/2” X 24-1/2” section from the
remaining portion of the Handi Panel.
Drill ¼” holes ¾” from sides and top and place
another hole ¾” from the top in the middle of the
panel.
3.4 – Mark and Drill Plastic
The easiest way to mark the clear panel hole
location is to align to desired location on the panel
and trace hole locations. Depending on the type and
thickness of Lexan or Plexiglas purchased you can
ether drill or punch (paper hole punch) the fastening
holes.
NOTE: Make the hole in the clear panel slightly
larger than the fastener (1/4” minimum).
Step 3 Topper and
whiteboard
Assemble
Size the panel
Mark and drill Plastic