Project

5
Layout Panel
1.1 – Lay Out Panel
Using the drawing as a guide, layout the
Panel as directed. A helpful hint:
If using factory cut panels, for the top,
confirm the dimensions are correct and the board is
square.
1.2 – Cut and Drill Parts
When cutting miters, pay attention to the
embossed side of the product. The embossed side
should face the interior or back of the project.
1.3 – Assemble Frame
Using PVC Cement and CA glue, pre-
assemble the paper holder.
1.4 – Assemble Frame
PVC Cement and wood screws are used to
attach the paper holder. Predrill and countersink
the wood screw to eliminate interference with the
wall attachment.
Step 1 Cut Board Parts
Cut and Drill Parts
Assemble Frame
Attach Frame
Layout Panel
1.1 – Lay Out Panel
Using the drawing as a guide, layout the
Panel as directed. A helpful hint:
If using factory cut panels, for the top,
confirm the dimensions are correct and the board is
square.
1.2 – Cut and Drill Parts
When cutting miters, pay attention to the
embossed side of the product. The embossed side
should face the interior or back of the project.
1.3 – Assemble Frame
Using PVC Cement and CA glue, pre-
assemble the paper holder.
1.4 – Assemble Frame
PVC Cement and wood screws are used to
attach the paper holder. Predrill and countersink
the wood screw to eliminate interference with the
wall attachment.
Step 1 Cut Board Parts
Cut and Drill Parts
Assemble Frame
Attach Frame
Step 1: Cut Board Parts
1.1 – Lay Out Panel
Using the drawing as a guide, layout the Panel as
directed. A helpful hint:
If using factory cut panels, for the top, conrm the
dimensions are correct and the board is square.
1.2 – Cut and Drill Parts
When cutting miters, pay attention to the embossed
side of the product. The embossed side should face the
interior or back of the project.
1.3 – Assemble Frame
Using PVC Cement and CA glue, pre-assemble the
paper holder.
1.4 – Assemble Frame
PVC Cement and wood screws are used to attach the
paper holder. Predrill and countersink the wood screw to
eliminate interference with the wall attachment.
Layout Panel
Assemble Frame
Cut and Drill Parts
Attach Frame
Layout Panel
1.1 – Lay Out Panel
Using the drawing as a guide, layout the
Panel as directed. A helpful hint:
If using factory cut panels, for the top,
confirm the dimensions are correct and the board is
square.
1.2 – Cut and Drill Parts
When cutting miters, pay attention to the
embossed side of the product. The embossed side
should face the interior or back of the project.
1.3 – Assemble Frame
Using PVC Cement and CA glue, pre-
assemble the paper holder.
1.4 – Assemble Frame
PVC Cement and wood screws are used to
attach the paper holder. Predrill and countersink
the wood screw to eliminate interference with the
wall attachment.
Step 1 Cut Board Parts
Cut and Drill Parts
Assemble Frame
Attach Frame
Layout Panel
1.1 – Lay Out Panel
Using the drawing as a guide, layout the
Panel as directed. A helpful hint:
If using factory cut panels, for the top,
confirm the dimensions are correct and the board is
square.
1.2 – Cut and Drill Parts
When cutting miters, pay attention to the
embossed side of the product. The embossed side
should face the interior or back of the project.
1.3 – Assemble Frame
Using PVC Cement and CA glue, pre-
assemble the paper holder.
1.4 – Assemble Frame
PVC Cement and wood screws are used to
attach the paper holder. Predrill and countersink
the wood screw to eliminate interference with the
wall attachment.
Step 1 Cut Board Parts
Cut and Drill Parts
Assemble Frame
Attach Frame