CENTURY OVAL Pools ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS CENTURY - OVAL - page 1
Installation Instructions 3. Do not attempt to lift the heavy boxes by yourself. To HOW TO USE THESE INSTRUCTIONS Be sure to read these instructions completely before reduce the possibility of personal injury, have someone help you move heavy boxes (pool wall, liner, etc.). beginning the installation of your pool. ATTENTION: warning Always use these assembly instructions to install 1. Your pool must be level within 2-3 cm all around. your swimming pool.
POOL SIZES Where to position my pool? Before you start building your pool, pay attention to the 6,10 x 3,60m following points: 1. Garden fence. 2. Trees, roots, overhanging branches and falling pool radius clearance radius leaves. 3. Underground wiring or cables. 4. Position pool with regard to sun terrace or sunken 301 sitting area. 301 177 177 5. Position pool with regard to the sunshine. 6. Supervision of small children. 360 210 centerline 244 7. Convenient location of filter and pump.
POOL LAYOUT STAKES AND STRING LINES Step 1 Step 3 string line support width level tops string line string line centerline of pool clearance radius side support excavations (see step 4) string line locations By means of the plan you determine the layout of the Locate 4 stakes C, D, E and F in accordance with indi- clearance. Locate stakes A and B (in accordance with cated measures of the plan of your pool.
EXPLODED SIDE SECTION INSTALL CONCRETE BLOCKS Step 5 side support assembly string line Fill with concrete skid plate horizontal beam level concrete block Figure A Legend for Figure A Place two concrete blocks into the excavations and 11/a/b = Bottom rail place the assembled side supports into each trench 16 = Screws #10 x 1/2" perpendicular, so that the front side of the side support 34 = Antiskid plate is situated to the tautly wire.
POSITION SIDE VERTICAL SHIMS (WITH PROTRUDING HORIZONTAL BEAM) INSTALL PRESSURE PADS Step 7 Step 5b # 10 Screws Begin here slope # 12 Screws # 12 Screws side support assembly pressure pad level fill with concrete firm undisturbed earth Work from left to right concrete blocks notch out Place the horizontal beam level. The side supports will Fix the pressure pads both to each other and to the stand straight again by the pressure of the water.
INSTALL BOTTOM RAILS NOTE: Place enough sifted earth into the pool area to cover the pressure pads. With a high groundwater level Step 9 (in ground pool) we advise to install a concrete floor. Only for 16" and 21" pools, stamped TR (4 pcs) Bottom rails stamped 12", 16", 18" and 21" INSTALL WALL JOINTS Step 11 Level Bottom rail connector Bottom rails Screw Optional sunk patio blocks Bolt Slide the bottom rails into the vertical end caps, groove up (see plan).
STEEL TOP RAIL / END SECTION INSTALL TOP RAILS + HOLES CHART FOR TOP RAILS (CENTURY 6,10 x 3,60 / 7,30 x 3,60) Step 13a There are two different joints, a straight and a round joint. A, B, C straight / D round (see fig. 13 A). Four screws connect the top rails with the vertical end caps. Screw the screws in the right holes of the top rails and vertical end caps. Follow the measures of the holes chart. Holes with numbers 1 and 3 are of the inside of the pool.
INSTALL TOP RAILS + HOLES CHART FOR TOP RAILS (CENTURY 8,50 x 4,90) COVE Step 14 Step 13b 15cm Cove 10cm There are two different joints, a straight and a round joint. A, B, C straight / D round (see fig. 13 B). Four screws connect the top rails with the vertical end caps. Screw the screws in the right holes of the top rails Warning: Use sifted earth, so that the cove can not crumble. and vertical end caps. Follow the measures of the holes chart.
STRETCH LINER into the pool until the desired tautness is achieved and re-clamp the binder clips. Remember that you are Step 16 monitoring a minimum tightness of the liner over rail that will control the liner seating itself against the pool floor and up the side with no wrinkles. When the water (5 cm) bottom liner seam is covering the pool floor, the liner on the pool floor must be without pleats and wrinkles.
PROCEDURE TO ATTACH LINER Now assemble the skimmer, inlet and filter as indicated on the special enclosed instruction. Then fill the pool to Step 19 the indicated level on the skimmer plate. fold back liner from 3 top rails top connector top rail stabilizer rails vertical end cap With the help of two or three people, raise and hold the liner up from any three top rail sections. Be careful and never allow the liner to fall back into the pool.
SUPPLEMENTARY INSTRUCTIONS FOR BUILDING A POOL IN THE GROUND To avoid that material rolls onto the site where the pool is to be constructed, the location where the pool is to INSTALLATION OF SKIMMER AND INLET be constructed must be in the most elevated part of the The skimmer and the inlet have to be installed before garden. The surrounding landscape should be lower the pool is filled with water and before the pool is filled than the pool.
Feed towards pump gate of filter Check valve (Recommended) Space between the top of the pool and stabilizer sand 22 cm Retour towards return gate filter Grade 2 cm per meter Stabilisierter Sand Füllen Sie erst das Schwimmbecken, bevor Sie den stabilisierten Sand auffüllen. Valve (Recommended) PVC tube and fixtures FIG. 2 SPECIFIC INSTALLATION bility to have easy access for maintenance or repairs.
Standard SKIMMER Fig. 1 Standard Skimmer MODELS 5-2091-015 INSTALLATION INSTRUCTIONS Cover Outside pool Inlet Sand filter Pool pump PREPARATION OF THE POOL The pool should be built up the correct way based on the pool assembly and installation instructions. Approximately 70 cm water should press against the metal wall, so that there isn’t any elasticity anymore against the liner, before the skimmer is installed. ATTENTION: After the skimmer hole is cut open the liner can no longer be moved.
Installation inlet fixture Fig. 2 1. Install the gasket of the inlet (17) into the wall opening. Insert the inlet fixture (18) through the liner and Inside pool Skimmer plate the wall starting from the inside of the pool. Make a small notch into the liner and press the inlet fixture through. 2. Now screw the inlet (16) onto the inlet fixture; turn it clockwise until the inlet end points towards the Skimmer valve Suction connection for cleaning pool bottom. 3.
Warning: Never try to install the cover in a suctioning Lid position if the pump is switched on. The cover might Vacuum adaptor suddenly be pulled down due to the strong suction of the pump. You may suffer personal injury to your hands or fingers. 5. When the cover is in place, you can switch on the Suction cover Fig. 7 pump and put into operation the suction of the pool floor. 6. When you are finished suctioning, you have to switch 3.
PREPARING FOR WINTER When the swimming season is over, you have to follow the instructions to get your pool ready for winter. ATTENTION! Do not remove all the water from your pool and also do not remove the liner. An empty pool can namely cause pool failure. Lower the water level - Lower the water level in your pool so that it is approximately 6” (15 cm) below the inlet fixture; maintain this water level by checking it regularly.
