Air-Operated Waste Oil Drainer Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Roughneck™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This oil drainer is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Specific Operation Warnings .......................
Intended Use The Roughneck Air-Operated Waste Oil Drainer is used for draining waste oil from engines, gear boxes, and differentials of all vehicles. It can be equipped with a special support to allow filters to drain. The hand wheel connecting seat easily adjusts the height of the oil collecting bowl. Technical Specifications #57139 #57142 Air inlet 1/4" NPT 1/4" NPT Extension funnel Yes Yes Capacity 65L/17 Gal 90L/24 Gal • Max draining pressure：1 bar/14.5 psi • Draining hose length：2000mm/78.
Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust. The product can create sparks, which may ignite the flammable liquids, gases, or dust. Do not allow the product to come into contact with an electrical source.
the power switch is dangerous and must be repaired by an authorized service representative before using. Disconnect the power/air supply from the product and place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store the product when it is not in use. Store it in a dry, secure place out of the reach of children.
Part No. Description Quantity Part No. Description Quantity 1 Oil collecting bowl assembly 1 5 Ball valve 1 2 Reservoir 1 6 Quick plug 1 3 Tool tray 1 7 Discharging hose assembly 1 4 Safety valve 1 Assembly Instructions Insert the tube (N) into the reservoir, then turn the hand wheel (O) clockwise and tighten.
Page 8 of 18
Assemble the handle (B) and the air inlet fitting. Turn off the ball valve (H). Assemble the supporting tube, ball valve (P), oil collecting bowl, filtrating plank, and extension funnel orderly.
Before Each Use ⚠WARNING Always wear the proper personal protective gear including ANSI Z87.1 compliant safety goggles and heat-resistant rubber gloves when using this product. Use only on a dry, clean, level surface capable of supporting the weight of the vehicle. Engine exhaust contains carbon monoxide; an odorless, invisible gas that can cause injury or death. Do not run the vehicle’s engine while using this product. Never work under a vehicle without the proper support devices.
Collecting Close all the valves (P, H, and I). Turn on the valve (H) and the valve (P) . Place the oil drainer under the car to collect the waste oil. Turn on the valve (P).
Draining Close all the valves (P, H, and I), place the spout (M) into the waste oil tank, and open the valve (I). Connect the air supply.
Open the valve (H) for draining. After Each Use ⚠WARNING Store the equipment in a dry place with good ventilation. Do not expose it to excessive heat, humidity or sunlight. Never let it touch any corrosive substances. Used engine oil is toxic and should be properly disposed of or recycled. Maintenance Maintain the product by adopting a program of conscientious repair and maintenance in accordance with the following recommended procedures.
Parts Diagram Parts List Part No. Description Qty. Part No. Description Qty.
Part No. Description Qty. Part No. Description 1-1 Check nut 1 1-8 Supporting tube 1 1-2 Compression spring 1 1-9 Ball valve 1 1-3 O-ring 2 1-10 Nut 1 1-4 Sealing bush 1 1-11 Retainer sleeve 1 1-5 O-ring 4 1-12 Oil collecting bowl 1 1-6 Expansion cover 1 1-13 Filtrating plank 1 1-7 Hand wheel 1 Page 15 of 18 Qty.
Part No. Description Qty. Part No. Description Qty.
Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. When ordering parts, the following information will be required: item description, item model number, item serial number/item lot date code, and the replacement part reference number.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.
