Owners Manual
Table Of Contents
- Getting Started
- Controlling the Remote Zones
- System Flexibility
- System Highlights
- Component Description
- RMZ-955 Controller/Amplifier
- System Planning
- RR-952 IR Remote Control
- RSM-901 Sensor/Display
- RKP-901 Keypad
- RSM-901/RKP-901 Combination
- Placement
- Connections:
- IR Flood Emitter
- IR Repeater Jacks
- System Wiring Considerations
- Data Cable and Connectors
- Speaker Cables
- Zone Configuration
- Basic Zone Complement
- Loudspeakers
- Installation: RMZ-955 Controller
- AC Line Connections
- AC for the RMZ-955
- AC for Source Components
- Rotel RLC-900 AC line conditioner
- Special AC features
- Source connections
- Source inputs
- Source outputs
- Speaker Connections
- Preamp outputs
- Variable vs. Fixed Level
- Data cable connections
- Infrared Control System
- Front Panel IR Flood Emitter
- Rear Panel IR Repeaters
- Paging Input
- Paging Inhibit
- Installation: Zone Control Devices
- RSM-901 Sensor/Display
- RSM-901 Mounting
- RSM-901 Data Connections
- Battery Enable
- Zone Configuration
- Source Component Labels
- Master/Slave Configuration
- System Reset
- Source Component Set-up
- RKP-901 Keypad
- RKP-901 Mounting
- RKP-901 Data Connections
- Zone Connection Strategies
- Installation: Multi-controller Systems
- AC Power
- AC Connections
- AC Link
- Manual AC Override
- Source Connections
- IR Connections
- For 2 RMZ-955s (5 to 8 zones):
- For 3 RMZ-955s (9-12 zones):
- For 4 RMZ-955s (13-16 zones):
- Exception: Multiple IR Flood Emitters
- Paging Connections
- Notes on multi-controller set-up
- Power Toggle Set-up
- Source Component Set-up
- “Engaged” Indicator
- System Set-up & Programming
- Source Commands
- Source Command Set-up
- Power Toggle
- Operating Instructions
- RR-952 Hand-held Remote
- Input Selector Buttons
- Tuner control buttons
- CD control buttons
- Tape/Satellite TV control buttons
- Video/LD control buttons
- Mute
- VOLUME UP/VOLUME DOWN
- STBY
- “X”
- RKP-901 Keypad
- Input Select commands
- System commands
- Source Control Commands
- RSM-901 Sensor/Display
- Controls and Displays
- Dot Matrix Display
- Setting Alarm, Time, & Custom Functions
- For Assistance
MULTI-ROOM SYSTEM CONTROLLER RMZ-955
30
Volume Level: When the Volume setting is changed in the Zone,
the RSM-901 will momentarily display the new setting:
Minimum Volume Maximum Volume
When a MUTE signal is sent, the volume display will ramp down
to zero and show the message “MUTE”. When the Zone is un-
muted, the display will ramp up to its previous level.
If a Paging signal is received, the display will ramp down to zero
and show a “(())” message during the page. If the Zone is muted,
the Paging indicator will show immediately. If the Zone is in
standby, the Paging indicator will be preceded by the turn-on
greeting.
Muting Indicator Paging Indicator
Setting Alarm, Time, and Custom Functions
The following custom functions are programmed from the
RSM-901’s Set-Up mode:
• Activating Wake-up Alarm
• Setting Alarm Time
• Setting default source that plays when Alarm activates
• Setting Time of Day
To enter the Set-Up mode, press the MODE button when the
Zone is in stand-by mode (clock display showing). Continuing to
press the MODE button will toggle through the four set-up
choices above and then back to the standby mode.
After the first function has been selected, the RSM-901 will auto-
matically exit the Set-Up mode and return to stand-by status if no
button is pressed for approximately 10 seconds. Any changes
made to the set-up configuration will be stored.
To set the alarm and time, press the MODE button to step
through the following procedure. The diagrams show momentary
indications of the functions being set prior to their status being
shown.
a) Turning Alarm ON or OFF:
Press the MIN button to activate the wake-up alarm. Press the
HOUR button to deactivate. The ALARM LED reminds you that the
alarm has been activated. When finished, press the MODE but-
ton to record your changes and advance to the next step.
ALARM
OFF
ALARM
ON
MODE
HOUR
MIN
PM
ALARM
RECEIVE
b) Setting Alarm Time:
The display will show the last alarm time set. Use the HOUR and
MINUTE buttons to advance to the desired Alarm time.
Make
sure that the PM indicator shows the desired 12 hour period for
the alarm.
When finished, press the MODE button to record your
changes and advance to the next step.
HOUR
BUTTON
MINUTE
BUTTON
MODE
HOUR
MIN
PM
ALARM
RECEIVE