Owners Manual
Table Of Contents
- Getting Started
- Controlling the Remote Zones
- System Flexibility
- System Highlights
- Component Description
- RMZ-955 Controller/Amplifier
- System Planning
- RR-952 IR Remote Control
- RSM-901 Sensor/Display
- RKP-901 Keypad
- RSM-901/RKP-901 Combination
- Placement
- Connections:
- IR Flood Emitter
- IR Repeater Jacks
- System Wiring Considerations
- Data Cable and Connectors
- Speaker Cables
- Zone Configuration
- Basic Zone Complement
- Loudspeakers
- Installation: RMZ-955 Controller
- AC Line Connections
- AC for the RMZ-955
- AC for Source Components
- Rotel RLC-900 AC line conditioner
- Special AC features
- Source connections
- Source inputs
- Source outputs
- Speaker Connections
- Preamp outputs
- Variable vs. Fixed Level
- Data cable connections
- Infrared Control System
- Front Panel IR Flood Emitter
- Rear Panel IR Repeaters
- Paging Input
- Paging Inhibit
- Installation: Zone Control Devices
- RSM-901 Sensor/Display
- RSM-901 Mounting
- RSM-901 Data Connections
- Battery Enable
- Zone Configuration
- Source Component Labels
- Master/Slave Configuration
- System Reset
- Source Component Set-up
- RKP-901 Keypad
- RKP-901 Mounting
- RKP-901 Data Connections
- Zone Connection Strategies
- Installation: Multi-controller Systems
- AC Power
- AC Connections
- AC Link
- Manual AC Override
- Source Connections
- IR Connections
- For 2 RMZ-955s (5 to 8 zones):
- For 3 RMZ-955s (9-12 zones):
- For 4 RMZ-955s (13-16 zones):
- Exception: Multiple IR Flood Emitters
- Paging Connections
- Notes on multi-controller set-up
- Power Toggle Set-up
- Source Component Set-up
- “Engaged” Indicator
- System Set-up & Programming
- Source Commands
- Source Command Set-up
- Power Toggle
- Operating Instructions
- RR-952 Hand-held Remote
- Input Selector Buttons
- Tuner control buttons
- CD control buttons
- Tape/Satellite TV control buttons
- Video/LD control buttons
- Mute
- VOLUME UP/VOLUME DOWN
- STBY
- “X”
- RKP-901 Keypad
- Input Select commands
- System commands
- Source Control Commands
- RSM-901 Sensor/Display
- Controls and Displays
- Dot Matrix Display
- Setting Alarm, Time, & Custom Functions
- For Assistance
17
System Reset
After changing any of the above configurations, reset the
RSM-901 by pressing the RESET switch (SW1). This is essential
to allow the new setting to take effect.
Source Component Set-up
After installation, refer to
System Set-up and Programming
(page
21)
for configuring the proper data codes for source component
operation.
Remember that an RSM-901 connected to the Zone A data cable
terminal MUST be used for initial set-up, particularly in systems
where non-Rotel source components are included.
Note: After completing the installation and component set-up,
power down the system, wait approximately 30 seconds, and
then power it up again. Test all functions.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
RKP-901 Keypad
VOLUME
TUNER
VIDEO
DISC
OFF
CD
AUX
*
MUTE
RKP-901 Mounting
The RKP-901 keypad mounts in a wall box in the same manner as
the RSM-901 sensor/display. There are no restrictions on where
the RKP-901 can be located. Common sense and user conve-
nience should be the determining factors. Alternatively, the
RKP-901 can be mounted in a double-width wall box with an
RSM-901 sensor/display. This is the most sensible arrangement
from an installation viewpoint (fewer cable runs) but may not be
practical in all rooms.
MODE
HOUR
MIN
PM
ALARM
VOLUME
RECEIVE
TUNER
VIDEO
DISC
OFF
CD
AUX
*
MUTE
RKP-901 Data Connections
RKP-901s do not need to be set for particular zones or configured
as Master/Slaves because they do not display zone or system
status information.
Data cable terminations and connections are made the same
way as previously detailed. As does the RSM-901, each RKP-901
has two data terminals (“In” and “Out”) located at the bottom of
its circuit board. Connect the “Out” terminal, either to the “In”
terminal of an RSM-901 in the zone, or to the RMZ-955 controller
if the zone does not have a RSM-901.
OUTPUT DATA CONNECTOR
Connect to RSM-901 Input
or to RMZ-955 if used
without RSM-901
OUTIN
INPUT DATA CONNECTOR
Connect from output of
RKP-901 or subsequent
RSM-901 in the zone.
INSTALLATION: ZONE CONTROL DEVICES