Swipe Match-on-Card Family Readers Installation Manual Models: AY-B1663 AY-B4663 November 2009
Table of Contents Table of Contents 1 2 Introduction ............................................................................... 3 General Overview ..................................................................... 5 2.1 Features .............................................................................. 5 3 4 5 6 Technical Specifications ........................................................... 6 Mounting Instructions ..............................................................
Introduction 1 Introduction Mifare® Smart Card Fingerprint Swipe Sensor MOC (Match-OnCard technology, developed by Rosslare) Readers are biometric fingerprint readers that are used with access control systems.
Introduction ® Figure 3: AY-B4663 Rambo Mifare Smart Card and Fingerprint Swipe This Installation Manual contains the following information: • Overview • Technical Specifications • Mounting Instructions • Wiring Instructions • Configuring the Reader • Testing the Reader • Modes of Operation Swipe Family Readers Installation Manual Page 4
General Overview 2 General Overview Mifare® Smart Card Fingerprint Swipe Sensor MOC Readers use a Swipe type biometric sensor to check for 1:1 verification between fingerprint data and a biometric template stored in a Mifare® card. When verification is confirmed, the Reader then transmits the Card ID or any ID stored in sector 0 or 15 to the Access Controller, which compares the card ID to data stored in the database and decides access granting.
Technical Specifications 3 Technical Specifications General Characteristics Model Numbers Output Formats • AY-B4663 • AY-B1663 • Wiegand 26 (default) • Wiegand 26 with facility code • Wiegand 32 reversed • Clock & Data • Wiegand 32 • Wiegand 34 • Wiegand 40 Read Range (max) 4 cm (1.
Technical Specifications Environmental Characteristics Operating Temp. Range -25°C to 60°C -13°F to 140°F Storage Temp. Range -40°C to 85°C -40°F to 140°F Operating Humidity 5% – 95% (non-condensing) Dimensions Reader Height x Width x Depth Weight AY-B1663 85.4 x 50.6 x 27 mm 3.36 x 1.99 x 1.06 inch 65 g 2.3 oz. AY-B4663 70.1 x 54.1 x 39.1 mm 2.76 x 2.13 x 1.54 inch 90 g 3.2 oz.
Mounting Instructions 4 Mounting Instructions Prior to starting, select the location where the controller unit is to be mounted. Use the supplied drilling template to assist in locating and drilling the appropriate holes. AY-B1663 AY-B4663 Figure 4: Mounting orientations Note: Be sure to protect the swipe sensor when the Reader is mounted outside. To mount the Reader: 1. Determine an approximate surface location for the Reader. 2.
Mounting Instructions 7. Carefully remove the snap-off front cover of the Reader to reveal two screw holes. AY-B1663 AY-B4663 Figure 5: Removing the Top Cover 8. Route the interface cable from the Reader to the Controller. Note: The Reader can also be mounted using strong epoxy glue. After application, firmly hold the Reader in place until the glue dries. 9. Carefully re-attach the snap-off front cover of the Reader and secure the case security screw at the bottom using the security hex key.
Wiring Instructions 5 Wiring Instructions Mifare® Smart Card Fingerprint Swipe Sensor MOC Readers are supplied with a 7- wire, 18-inch cable. To connect the Reader to the Controller: 1. Prepare the Reader cable by cutting the cable jacket back 1¼ inches, and by stripping the wires ½ an inch. 2. Prepare the Controller cable by cutting the cable jacket back 1¼ inches, and by stripping the wires ½ an inch. 3.
Configuring the Reader 6 Configuring the Reader To provide the highest level of security, the Reader is programmed to validate only Mifare® cards whose settings correspond to the Master card that is used to configure the Reader.
Testing the Reader 7 Testing the Reader After wiring the Reader to the Controller and to a power supply, test the Reader. To test the Reader: 1. Power up the Reader. 3 long beeps are generated, and all 3 LEDs flash simultaneously for 3 seconds. After 30 seconds, the LEDs illuminate alternately, from top to bottom. 2. Present the appropriate type of card to the Reader.
Modes of Operation 8 Modes of Operation Mifare® Smart Card Fingerprint Swipe Sensor MOC Readers have the following modes of operation: • Boot mode (Reset) • Configuration Mode • Standby mode • Read mode • Lockout mode 8.1 Boot Mode The Reader enters Boot mode upon power up or upon restoration of power after a power failure where the loader runs separately from the main application.
Modes of Operation • After a successful card or fingerprint read During Standby mode, the LEDs turn on and off in circular motion at a slow rate to indicate standby mode and the Reader is ready for normal use. 8.4 Read Mode The Reader enters Read mode when a user presents a Mifare® card, followed by a swipe of the finger. The card and/or fingerprint can have a valid or invalid value and / or match. 8.4.
Modes of Operation • There is a mismatch between the fingerprint and the template (e.g., the user presents the wrong finger). When a card or fingerprint read is invalid, the following sequence occurs: 1. A user presents a Mifare® card to the Reader. This can occur during Standby mode (at the beginning of the identification procedure), or following a successful read of the first means of identification. 2.
Limited Warranty Appendix A Limited Warranty ROSSLARE ENTERPRISES LIMITED S (Rosslare) TWO YEARS LIMITED WARRANTY is applicable worldwide. This warranty supersedes any other warranty. Rosslare's TWO YEARS LIMITED WARRANTY is subject to the following conditions: Warranty Warranty of Rosslare's products extends to the original purchaser (Customer) of the Rosslare product and is not transferable. Products Covered By This Warranty and Duration ROSSLARE ENTERPRISES LTD.
Limited Warranty Exclusions and Limitations ROSSLARE shall not be responsible or liable for any damage or loss resulting from the operation or performance of any Product or any systems in which a Product is incorporated. This warranty shall not extend to any ancillary equipment not furnished by ROSSLARE, which is attached to or used in conjunction with a Product, or to any Product that is used with any ancillary equipment, which is not furnished by ROSSLARE.
Technical Support Appendix B Technical Support Asia Pacific, Middle East, Africa Rosslare Security Products Headquarters 905-912 Wing Fat Industrial Bldg, 12 Wang Tai Road, Kowloon Bay Hong Kong Tel: +852 2795-5630 Fax: +852 2795-1508 E-mail: support.apac@rosslaresecurity.com United States and Canada 1600 Hart Court, Suite 103 Southlake, TX, USA 76092 Toll Free:+1-866-632-1101 Local:+1-817-305-0006 Fax: +1-817-305-0069 E-mail: support.na@rosslaresecurity.
0706-0960334+00 www.rosslaresecurity.
