User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. HOMELOGIXTM QUICK REFERENCE
- 3. SPECIFICATIONS
- 4. USER MENU STRUCTURE
- 5. INSTALLATION
- 6. PROGRAMMING HOMELOGIXTM
- 7. INSTALLERS MENU
- 7.1 Accessing the Installer Menu
- 7.2 Change Code
- 7.3 Zones
- 7.4 Enrolling
- 7.5 Security
- 7.5.1. Exit Delay
- 7.5.2. Entry Delay
- 7.5.3. Auto Arming
- 7.5.4. Siren Time
- 7.5.5. Siren Mode
- 7.5.6. Relay Polarity
- 7.5.7. Local Siren
- 7.5.8. Supervision Time
- 7.5.9. Jamming
- 7.5.10. No Activity Time
- 7.5.11. Trouble Beeps
- 7.5.12. Bypass
- 7.5.13. Quick Arm
- 7.5.14. Panic Button
- 7.5.15. Duress Code
- 7.5.16. Alarm Cancel
- 7.5.17. Alarm Abort Time
- 7.5.18. Backlight Time
- 7.5.19. Hide Display
- 7.5.20. Key Beeps
- 7.6 Communications
- 7.7 Automation
- 7.8 Messages
- 7.9 Maintenance
- 8. READING THE EVENT LOG
- Annex I. ACCESSORIES
- I.1 HomeLogiXTM Compatible Detectors
- I.1.1. Wireless Passive Infra-Red (Motion) Detector
- I.1.2. Advanced Wireless Spherical PIR (Motion) Detector
- I.1.3. Magnetic Contact Sensor
- I.1.4. Glass Break Detector
- I.1.5. Universal Wire to RF (Two-Channel) Transmitter
- I.1.6. Smoke and Heat Detectors
- I.2 HomeLogiXTM Compatible Remotes
- I.2.1. Wireless 3-Button Remote Control Transmitter
- I.2.2. Wireless Emergency Panic Pendant
- I.2.3. 1, 2 or 4-Button Remote Controls
- I.2.4. HomeLogiXTM Compatible Wireless Siren
- I.2 HomeLogiXTM Compatible Remotes
- I.1 HomeLogiXTM Compatible Detectors
- Annex I. ACCESSORIES
ACCESSORIES
HomeLogiX Installer Manual Page 40
Annex I. ACCESSORIES
I.1 HomeLogiX
TM
Compatible Detectors
A wide assortment of wireless detectors is compatible with the HomeLogiX
TM
control
panel, primarily for use in intrusion and personal safety applications. There are also
other system components, such as RF repeaters for extending range, and wireless
sirens for remote annunciation of alarms. To cover all the possible solutions of
integration, a Universal RF Transmitter is available, which can interface with almost any
type of wired sensor and enable it to communicate to the HomeLogiX
TM
by radio link.
Note:
For the model numbers shown below, XX denotes a variation on frequency and
country of application. Each detector comes with its own installation manual. All
the wireless detectors are powered by high-capacity lithium primary cells, which
provide long battery life.
The control panel identifies the detectors by means of a unique three-byte
identification code (ID Code), which offers up to 16 million possible combinations. The
ID is transmitted with every radio message. In addition to the ID, each detector
provides local intelligence of events such as the following, by radio link to the panel:
• Tamper open and restore events;
• Alarm events;
• Low battery and restore events.
Each detector also generates a supervisory full status transmission every 20 minutes.
I.1.1. Wireless Passive Infra-Red (Motion) Detector
This sensor (Figure 1) is used to secure volumetric indoor areas. It employs a precision-
optics patented Fresnel lens, an ultra-sensitive infrared silicon sensor, and advanced
microcontroller digital signal analysis. The sensor is housed in tamper-detection
housing. The sensor can be mounted to any rigid flat or corner surface to cover the
desired volumetric space to be protected; a corner mount is available to enable
corner tamper detection. When motion is detected, the PIR transmits a message to
the control panel. If the control panel is armed, then the system will generate an
alarm.
Figure 12 SA-01 Wireless PIR Motion Detector
I.1.2. Advanced Wireless Spherical PIR (Motion) Detector
This sensor (Figure 2) is used to secure volumetric indoor areas. It employs a unique
Spherical Fresnel lens with creep-zone and an optional snap-in curtain mask, an ultra-
sensitive infrared silicon sensor, and advanced microcontroller digital signal analysis.