User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. HOMELOGIXTM QUICK REFERENCE
- 3. SPECIFICATIONS
- 4. USER MENU STRUCTURE
- 5. INSTALLATION
- 6. PROGRAMMING HOMELOGIXTM
- 7. INSTALLERS MENU
- 7.1 Accessing the Installer Menu
- 7.2 Change Code
- 7.3 Zones
- 7.4 Enrolling
- 7.5 Security
- 7.5.1. Exit Delay
- 7.5.2. Entry Delay
- 7.5.3. Auto Arming
- 7.5.4. Siren Time
- 7.5.5. Siren Mode
- 7.5.6. Relay Polarity
- 7.5.7. Local Siren
- 7.5.8. Supervision Time
- 7.5.9. Jamming
- 7.5.10. No Activity Time
- 7.5.11. Trouble Beeps
- 7.5.12. Bypass
- 7.5.13. Quick Arm
- 7.5.14. Panic Button
- 7.5.15. Duress Code
- 7.5.16. Alarm Cancel
- 7.5.17. Alarm Abort Time
- 7.5.18. Backlight Time
- 7.5.19. Hide Display
- 7.5.20. Key Beeps
- 7.6 Communications
- 7.7 Automation
- 7.8 Messages
- 7.9 Maintenance
- 8. READING THE EVENT LOG
- Annex I. ACCESSORIES
- I.1 HomeLogiXTM Compatible Detectors
- I.1.1. Wireless Passive Infra-Red (Motion) Detector
- I.1.2. Advanced Wireless Spherical PIR (Motion) Detector
- I.1.3. Magnetic Contact Sensor
- I.1.4. Glass Break Detector
- I.1.5. Universal Wire to RF (Two-Channel) Transmitter
- I.1.6. Smoke and Heat Detectors
- I.2 HomeLogiXTM Compatible Remotes
- I.2.1. Wireless 3-Button Remote Control Transmitter
- I.2.2. Wireless Emergency Panic Pendant
- I.2.3. 1, 2 or 4-Button Remote Controls
- I.2.4. HomeLogiXTM Compatible Wireless Siren
- I.2 HomeLogiXTM Compatible Remotes
- I.1 HomeLogiXTM Compatible Detectors
- Annex I. ACCESSORIES
INSTALLERS MENU
HomeLogiX Installer Manual
Page 35
7.7 Automation
Change
Code
Zones Enrolling Security Communications
AUTOMATION
Messages Maintenance
Keypad Manual
Set Triggers
The sixth sub menu is Automation, which deals with the setup of various home
automation options. Browse the desired automation related setting, as described in
detail ahead, using the Menu button, press the Enter button to access it.
7.7.1. Keypad Manual
Enable or disable this option to determine whether the PGM output can be controlled
by numeric keys 1 and 2 of the keypad as described in the
Keypad Operated
Functions section above, this option is enabled by default.
To set up the keypad:
Using the Menu button, Enable or Disable the option and press Enter to confirm your
selection.
7.7.2. Set Triggers
Enables you to activate the PGM’s, using various events in an automated fashion. By
default, no triggers are set.
To set up triggers:
Using the Menu button, select PGM1 or PGM2, and press Enter to confirm.
For each of the PGM’s you can select the pulse time and triggers as described below:
• Pulse time - set the length of time for the device to stay on when a pulse type
activation is selected. Using the numeric keypad, set the time from 1 to 99
seconds and press Enter to save.
• Select the trigger type and parameters according to the following options:
Trigger PGM Activation Options Remarks
Arm Away On, Off, Pulse, Ignore
Arm Home On, Off, Pulse, Ignore
Disarm On, Off, Pulse, Ignore
Alarm Enabled, Disabled Go OFF when alarm stops
Panic Pulse, Ignore
Trouble Pulse, Ignore
AC Loss Enabled, Disabled ON when AC fails, OFF when AC returns
Remote Control On, Off, Pulse, Trouble, Ignore Relates to remote’s panic button
Zone On, Off, Pulse, Trouble, Ignore Relates to zone open or detection