User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. HOMELOGIXTM QUICK REFERENCE
- 3. SPECIFICATIONS
- 4. USER MENU STRUCTURE
- 5. INSTALLATION
- 6. PROGRAMMING HOMELOGIXTM
- 7. INSTALLERS MENU
- 7.1 Accessing the Installer Menu
- 7.2 Change Code
- 7.3 Zones
- 7.4 Enrolling
- 7.5 Security
- 7.5.1. Exit Delay
- 7.5.2. Entry Delay
- 7.5.3. Auto Arming
- 7.5.4. Siren Time
- 7.5.5. Siren Mode
- 7.5.6. Relay Polarity
- 7.5.7. Local Siren
- 7.5.8. Supervision Time
- 7.5.9. Jamming
- 7.5.10. No Activity Time
- 7.5.11. Trouble Beeps
- 7.5.12. Bypass
- 7.5.13. Quick Arm
- 7.5.14. Panic Button
- 7.5.15. Duress Code
- 7.5.16. Alarm Cancel
- 7.5.17. Alarm Abort Time
- 7.5.18. Backlight Time
- 7.5.19. Hide Display
- 7.5.20. Key Beeps
- 7.6 Communications
- 7.7 Automation
- 7.8 Messages
- 7.9 Maintenance
- 8. READING THE EVENT LOG
- Annex I. ACCESSORIES
- I.1 HomeLogiXTM Compatible Detectors
- I.1.1. Wireless Passive Infra-Red (Motion) Detector
- I.1.2. Advanced Wireless Spherical PIR (Motion) Detector
- I.1.3. Magnetic Contact Sensor
- I.1.4. Glass Break Detector
- I.1.5. Universal Wire to RF (Two-Channel) Transmitter
- I.1.6. Smoke and Heat Detectors
- I.2 HomeLogiXTM Compatible Remotes
- I.2.1. Wireless 3-Button Remote Control Transmitter
- I.2.2. Wireless Emergency Panic Pendant
- I.2.3. 1, 2 or 4-Button Remote Controls
- I.2.4. HomeLogiXTM Compatible Wireless Siren
- I.2 HomeLogiXTM Compatible Remotes
- I.1 HomeLogiXTM Compatible Detectors
- Annex I. ACCESSORIES
INSTALLERS MENU
HomeLogiX Installer Manual Page 34
selecting #1 (Listen), #3 (Talk), or #9 (Close communication) in the event the system
calls when an alarm is sounded. The installer can set the following options:
• CMS 2-way voice Enable/Disable
• CMS 2-way voice Timeout
However, if the KEY ON, TROUBLE, BYPASS, and MISC events are reported, and the
CMS is in LISTEN-IN mode, the CMS receptionist can hear the alarm/emergency voice
message events, if they belong to the same CMS.
On the other hand, if those events belong to another CMS, they will be reported after
the current CMS session report has finished.
To set up 2 way Voice Behavior:
1. In the 2WV SETUP menu, select CS 2WV ENABLE.
2. Select ENABLE.
3. Select CS 2WV TIMEOUT.
4. Enter a timeout value that does not exceed 180 seconds.
Note:
It is recommended to use 180 seconds for Timeout.
5. Press Exit to return to Normal mode.
7.6.7. Fax Defeat
When calling the system, fax and answering machines may need to be overridden.
This menu specifies whether to enable or disable this override. By default, this option is
disabled.
To set up Fax Defeat:
Using the Menu button, Enable or Disable the option and press Enter to confirm.
7.6.8. Number of Rings
Specify the number of rings before the system answers the line. By default, this option is
set to 4 rings.
To specify the number of rings:
Using the numeric keypad, set the number of rings to between 1 and 15, and press
Enter to confirm.
7.6.9. Select Region
Select the region in which the time is set for the system. By default, this option is set to 4
rings. By default, this option is Other.
To select the region:
Select the region from the drop down menu (or leave the default of Other), and press
Enter to confirm.