User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. HOMELOGIXTM QUICK REFERENCE
- 3. SPECIFICATIONS
- 4. USER MENU STRUCTURE
- 5. INSTALLATION
- 6. PROGRAMMING HOMELOGIXTM
- 7. INSTALLERS MENU
- 7.1 Accessing the Installer Menu
- 7.2 Change Code
- 7.3 Zones
- 7.4 Enrolling
- 7.5 Security
- 7.5.1. Exit Delay
- 7.5.2. Entry Delay
- 7.5.3. Auto Arming
- 7.5.4. Siren Time
- 7.5.5. Siren Mode
- 7.5.6. Relay Polarity
- 7.5.7. Local Siren
- 7.5.8. Supervision Time
- 7.5.9. Jamming
- 7.5.10. No Activity Time
- 7.5.11. Trouble Beeps
- 7.5.12. Bypass
- 7.5.13. Quick Arm
- 7.5.14. Panic Button
- 7.5.15. Duress Code
- 7.5.16. Alarm Cancel
- 7.5.17. Alarm Abort Time
- 7.5.18. Backlight Time
- 7.5.19. Hide Display
- 7.5.20. Key Beeps
- 7.6 Communications
- 7.7 Automation
- 7.8 Messages
- 7.9 Maintenance
- 8. READING THE EVENT LOG
- Annex I. ACCESSORIES
- I.1 HomeLogiXTM Compatible Detectors
- I.1.1. Wireless Passive Infra-Red (Motion) Detector
- I.1.2. Advanced Wireless Spherical PIR (Motion) Detector
- I.1.3. Magnetic Contact Sensor
- I.1.4. Glass Break Detector
- I.1.5. Universal Wire to RF (Two-Channel) Transmitter
- I.1.6. Smoke and Heat Detectors
- I.2 HomeLogiXTM Compatible Remotes
- I.2.1. Wireless 3-Button Remote Control Transmitter
- I.2.2. Wireless Emergency Panic Pendant
- I.2.3. 1, 2 or 4-Button Remote Controls
- I.2.4. HomeLogiXTM Compatible Wireless Siren
- I.2 HomeLogiXTM Compatible Remotes
- I.1 HomeLogiXTM Compatible Detectors
- Annex I. ACCESSORIES
INSTALLERS MENU
HomeLogiX Installer Manual Page 30
To set the alarm abort time:
Using the numeric keypad, set the alarm abort time between 01 – 60 seconds, or set it
to 00 to disable the option.
7.5.18. Backlight Time
Specifies the backlight options; by default, the backlight time is set at 15 seconds.
To set the backlight:
Using the Menu button, select one of the following options and press Enter to confirm:
• Always: to specify that the keypad and buttons are backlit at all times.
• 15 secs: to specify that the keypad and buttons are backlit for up to 15 seconds
after last key press.
7.5.19. Hide Display
Enables you to specify that when armed, the system will not display the system
statuses or other system prompts; by default, Hide Display is off.
To display the system status:
Using the Menu button, select one of the following options and press Enter to confirm:
• Off to display status and prompts.
• On to hide status and prompts.
7.5.20. Key Beeps
Choose to turn Key beeps on to hear a beep on each key press; by default, the Key
beeps is off.
To set the key beeps:
Using the Menu button, select one of the following options and press Enter to confirm:
• On to turn the key beeps on
• Off to turn the key beeps off