User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. HOMELOGIXTM QUICK REFERENCE
- 3. SPECIFICATIONS
- 4. USER MENU STRUCTURE
- 5. INSTALLATION
- 6. PROGRAMMING HOMELOGIXTM
- 7. INSTALLERS MENU
- 7.1 Accessing the Installer Menu
- 7.2 Change Code
- 7.3 Zones
- 7.4 Enrolling
- 7.5 Security
- 7.5.1. Exit Delay
- 7.5.2. Entry Delay
- 7.5.3. Auto Arming
- 7.5.4. Siren Time
- 7.5.5. Siren Mode
- 7.5.6. Relay Polarity
- 7.5.7. Local Siren
- 7.5.8. Supervision Time
- 7.5.9. Jamming
- 7.5.10. No Activity Time
- 7.5.11. Trouble Beeps
- 7.5.12. Bypass
- 7.5.13. Quick Arm
- 7.5.14. Panic Button
- 7.5.15. Duress Code
- 7.5.16. Alarm Cancel
- 7.5.17. Alarm Abort Time
- 7.5.18. Backlight Time
- 7.5.19. Hide Display
- 7.5.20. Key Beeps
- 7.6 Communications
- 7.7 Automation
- 7.8 Messages
- 7.9 Maintenance
- 8. READING THE EVENT LOG
- Annex I. ACCESSORIES
- I.1 HomeLogiXTM Compatible Detectors
- I.1.1. Wireless Passive Infra-Red (Motion) Detector
- I.1.2. Advanced Wireless Spherical PIR (Motion) Detector
- I.1.3. Magnetic Contact Sensor
- I.1.4. Glass Break Detector
- I.1.5. Universal Wire to RF (Two-Channel) Transmitter
- I.1.6. Smoke and Heat Detectors
- I.2 HomeLogiXTM Compatible Remotes
- I.2.1. Wireless 3-Button Remote Control Transmitter
- I.2.2. Wireless Emergency Panic Pendant
- I.2.3. 1, 2 or 4-Button Remote Controls
- I.2.4. HomeLogiXTM Compatible Wireless Siren
- I.2 HomeLogiXTM Compatible Remotes
- I.1 HomeLogiXTM Compatible Detectors
- Annex I. ACCESSORIES
INSTALLERS MENU
HomeLogiX Installer Manual
Page 27
To set the relay polarity:
Using the Menu button, select one of the two options, N.O. or N.C., and press Enter to
confirm.
7.5.7. Local Siren
Specifies whether an activated alarm causes an internal siren (emitted from the
system’s speaker) to sound or remain silent. The local siren is enabled by default.
To set up a local siren:
Using the Menu button, select one of the two options, Enable or Disable, and press
Enter to confirm.
7.5.8. Supervision Time
Specifies the time limit during which the system receives supervision reports from
specified wireless devices. If a device does not report-in at least once within the
specified time limit, the system initiates an inactivity alert. Default is set to one hour.
To specify the supervision time:
Using the Menu button, select on of the time limit options, 1, 2, 4, 6, 8, 16, 24 or 48
hours, during which the system receives reports and press Enter to confirm.
7.5.9. Jamming
Specifies whether the system detects and reports jamming – interferences on the radio
channel used by the system. The jamming detection is disabled by default.
To specify jamming detection:
Using the Menu button, select one of the following options and press Enter to confirm:
• Disabled: to disable jamming detection
• EN enabled: to enable European standard jamming detection
• UL enabled: to enable US standard jamming detection
7.5.10. No Activity Time
Specifies the time limit in which the system should receive a signal from a sensor used
to monitor the activity of sick, elderly or disabled people. If no device detects and
reports movement at least once within the specified time limit, a “not active alert”
sounds. This option is disabled by default.
To set the no activity time:
Using the Menu button, select one of the following options and press Enter to confirm:
• 1, 2, 5, 10, 15, or 30 minutes
• Disable the timer