User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. HOMELOGIXTM QUICK REFERENCE
- 3. SPECIFICATIONS
- 4. USER MENU STRUCTURE
- 5. INSTALLATION
- 6. PROGRAMMING HOMELOGIXTM
- 7. INSTALLERS MENU
- 7.1 Accessing the Installer Menu
- 7.2 Change Code
- 7.3 Zones
- 7.4 Enrolling
- 7.5 Security
- 7.5.1. Exit Delay
- 7.5.2. Entry Delay
- 7.5.3. Auto Arming
- 7.5.4. Siren Time
- 7.5.5. Siren Mode
- 7.5.6. Relay Polarity
- 7.5.7. Local Siren
- 7.5.8. Supervision Time
- 7.5.9. Jamming
- 7.5.10. No Activity Time
- 7.5.11. Trouble Beeps
- 7.5.12. Bypass
- 7.5.13. Quick Arm
- 7.5.14. Panic Button
- 7.5.15. Duress Code
- 7.5.16. Alarm Cancel
- 7.5.17. Alarm Abort Time
- 7.5.18. Backlight Time
- 7.5.19. Hide Display
- 7.5.20. Key Beeps
- 7.6 Communications
- 7.7 Automation
- 7.8 Messages
- 7.9 Maintenance
- 8. READING THE EVENT LOG
- Annex I. ACCESSORIES
- I.1 HomeLogiXTM Compatible Detectors
- I.1.1. Wireless Passive Infra-Red (Motion) Detector
- I.1.2. Advanced Wireless Spherical PIR (Motion) Detector
- I.1.3. Magnetic Contact Sensor
- I.1.4. Glass Break Detector
- I.1.5. Universal Wire to RF (Two-Channel) Transmitter
- I.1.6. Smoke and Heat Detectors
- I.2 HomeLogiXTM Compatible Remotes
- I.2.1. Wireless 3-Button Remote Control Transmitter
- I.2.2. Wireless Emergency Panic Pendant
- I.2.3. 1, 2 or 4-Button Remote Controls
- I.2.4. HomeLogiXTM Compatible Wireless Siren
- I.2 HomeLogiXTM Compatible Remotes
- I.1 HomeLogiXTM Compatible Detectors
- Annex I. ACCESSORIES
INSTALLERS MENU
HomeLogiX Installer Manual Page 26
To modify the entry delay:
Using the numeric keypad, specify the length of the entry delay between 1 and 99
seconds and press Enter to save your selection.
7.5.3. Auto Arming
Auto Arming allows scheduled arming and disarming of the system for all weekdays at
different hours.
To activate auto arm:
Using the Menu button, select the day of the week and press Enter to confirm.
Using the Menu button, select one of the following options and press Enter to confirm:
• Disabled
• Arm Home
• Arm Away
Enter a time (24 hour time convention) to arm the system using the numeric keys and
press Enter to confirm the time, repeat the process for the disarm time.
7.5.4. Siren Time
Specifies the amount of time the siren will sound when an alarm has been set off. The
siren time is set to three minutes by default. This relates to all siren types, wired, wireless
and local.
To specify the siren time:
Using the numeric keypad, specify the length of the siren time between 00 and 99
minutes (00 disables the siren) and press Enter to save your selection.
7.5.5. Siren Mode
You can specify whether you want the siren to be activated on Away only or both
away and home alarms, the siren mode is set at Away + Home by default. This relates
to all siren types, wired, wireless and local.
To specify the siren mode:
Using the Menu button, select one of the following options and press Enter to confirm:
• Away
• Away + Home
7.5.6. Relay Polarity
Depending on the input trigger of the hardwired siren you are using specify the relay
polarity to either Normally Open or Normally Closed. The siren relay polarity is set to
N.O. (normally open) by default.