User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. HOMELOGIXTM QUICK REFERENCE
- 3. SPECIFICATIONS
- 4. USER MENU STRUCTURE
- 5. INSTALLATION
- 6. PROGRAMMING HOMELOGIXTM
- 7. INSTALLERS MENU
- 7.1 Accessing the Installer Menu
- 7.2 Change Code
- 7.3 Zones
- 7.4 Enrolling
- 7.5 Security
- 7.5.1. Exit Delay
- 7.5.2. Entry Delay
- 7.5.3. Auto Arming
- 7.5.4. Siren Time
- 7.5.5. Siren Mode
- 7.5.6. Relay Polarity
- 7.5.7. Local Siren
- 7.5.8. Supervision Time
- 7.5.9. Jamming
- 7.5.10. No Activity Time
- 7.5.11. Trouble Beeps
- 7.5.12. Bypass
- 7.5.13. Quick Arm
- 7.5.14. Panic Button
- 7.5.15. Duress Code
- 7.5.16. Alarm Cancel
- 7.5.17. Alarm Abort Time
- 7.5.18. Backlight Time
- 7.5.19. Hide Display
- 7.5.20. Key Beeps
- 7.6 Communications
- 7.7 Automation
- 7.8 Messages
- 7.9 Maintenance
- 8. READING THE EVENT LOG
- Annex I. ACCESSORIES
- I.1 HomeLogiXTM Compatible Detectors
- I.1.1. Wireless Passive Infra-Red (Motion) Detector
- I.1.2. Advanced Wireless Spherical PIR (Motion) Detector
- I.1.3. Magnetic Contact Sensor
- I.1.4. Glass Break Detector
- I.1.5. Universal Wire to RF (Two-Channel) Transmitter
- I.1.6. Smoke and Heat Detectors
- I.2 HomeLogiXTM Compatible Remotes
- I.2.1. Wireless 3-Button Remote Control Transmitter
- I.2.2. Wireless Emergency Panic Pendant
- I.2.3. 1, 2 or 4-Button Remote Controls
- I.2.4. HomeLogiXTM Compatible Wireless Siren
- I.2 HomeLogiXTM Compatible Remotes
- I.1 HomeLogiXTM Compatible Detectors
- Annex I. ACCESSORIES
INSTALLERS MENU
HomeLogiX Installer Manual
Page 23
7.4.2. Remote Controls
You can enroll up to eight remote controls, and specify functions for each button on
the remote control. You can also delete enrolled remote controls.
To enroll a remote control and specify a function:
Select the desired remote control number 01-08 by either browsing the remotes using
the Menu button or by entering the remote number using the numeric keypad.
Enroll the remote control when the WAITING FOR SIGNAL message is displayed, by
pressing a button on the remote you wish to enroll, When the signal is detected you
will be asked to press the Enter button to store and save your selection. Once the
selection is stored, you can then choose to configure each of the remote control
buttons to behave in one of the following options:
• Restore Default (will set the button to it’s original functionality)
• Operate PGM 1
• Operate PGM 2
• Status Request
At any time press the Quick (ESC) button to exit the menu, Once you exited the menu
(after saving the enrollment) you cannot change the button’s behavior, unless you
delete the remote and re-enroll it.
To delete a remote control
Select the pre-enrolled remote control number 01-08 by either browsing the remotes
using the Menu button or by entering the remote number using the numeric keypad.
You will be asked whether you wish to delete it. Press Enter to delete the detector or
the Quick (ESC) button to go back.
7.4.3. RF Siren
You can enroll up to four RF Sirens. You can choose to remove enrolled sirens.
To enroll/remove an RF Siren:
• Select the required Siren location, #01-04 by either browsing the keys using the
Menu button or by entering the siren’s number using the numeric keypad
• Enroll the RF Siren when the WAITING FOR SIGNAL option is displayed, by
activating the siren’s tamper, When the signal is detected you will be asked to
press the Enter button to store and save your selection
• If the selected location has a siren enrolled, you will be asked whether you wish
to delete it. Press the Enter button to delete or the Quick (ESC) button to go
back