User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. HOMELOGIXTM QUICK REFERENCE
- 3. SPECIFICATIONS
- 4. USER MENU STRUCTURE
- 5. INSTALLATION
- 6. PROGRAMMING HOMELOGIXTM
- 7. INSTALLERS MENU
- 7.1 Accessing the Installer Menu
- 7.2 Change Code
- 7.3 Zones
- 7.4 Enrolling
- 7.5 Security
- 7.5.1. Exit Delay
- 7.5.2. Entry Delay
- 7.5.3. Auto Arming
- 7.5.4. Siren Time
- 7.5.5. Siren Mode
- 7.5.6. Relay Polarity
- 7.5.7. Local Siren
- 7.5.8. Supervision Time
- 7.5.9. Jamming
- 7.5.10. No Activity Time
- 7.5.11. Trouble Beeps
- 7.5.12. Bypass
- 7.5.13. Quick Arm
- 7.5.14. Panic Button
- 7.5.15. Duress Code
- 7.5.16. Alarm Cancel
- 7.5.17. Alarm Abort Time
- 7.5.18. Backlight Time
- 7.5.19. Hide Display
- 7.5.20. Key Beeps
- 7.6 Communications
- 7.7 Automation
- 7.8 Messages
- 7.9 Maintenance
- 8. READING THE EVENT LOG
- Annex I. ACCESSORIES
- I.1 HomeLogiXTM Compatible Detectors
- I.1.1. Wireless Passive Infra-Red (Motion) Detector
- I.1.2. Advanced Wireless Spherical PIR (Motion) Detector
- I.1.3. Magnetic Contact Sensor
- I.1.4. Glass Break Detector
- I.1.5. Universal Wire to RF (Two-Channel) Transmitter
- I.1.6. Smoke and Heat Detectors
- I.2 HomeLogiXTM Compatible Remotes
- I.2.1. Wireless 3-Button Remote Control Transmitter
- I.2.2. Wireless Emergency Panic Pendant
- I.2.3. 1, 2 or 4-Button Remote Controls
- I.2.4. HomeLogiXTM Compatible Wireless Siren
- I.2 HomeLogiXTM Compatible Remotes
- I.1 HomeLogiXTM Compatible Detectors
- Annex I. ACCESSORIES
INSTALLATION
HomeLogiX Installer Manual Page 14
open collector outputs Active Low.
GND
Ground
ZONE
Wired Zone (zone 40) Alarm input.
GND
Ground
TAMPER
Wired Zone (zone 40) Tamper input
.
+15VDC VIN
GND
Input voltage from AC/DC adaptor VIN=13.8-15 .
+13.8VDC (-) AUX
(OUT)
Auxiliary Power output (to power external devices) +13.8 VDC
500mA Load current Max. Current limited.
LINE IN
Telephone line in (from the wall to the system).
HOME TEL
Telephone line out (from system to telephone device).
Connection
Socket
Connection Socket for 10 pin plug connecting panel to PC with
MD-62.
+BAT-
Battery
5.4.2. SIREN RELAY OUTPUT Wiring to External Siren
Relay output for external siren can be programmed as normally open or normally
closed (fail-safe) operation.
Figure 4: Siren
This output can be programmed by the installer to provide normally closed or normally
open dry contact output. This relay output will toggle the normal position in case of an
alarm and operates in the same method as the local siren.
5.4.3. Wiring Auxiliary Outputs 1 and 2
Auxiliary outputs 1 and 2: This pair of outputs are open collectors with sink current
limited at 200 mA. The outputs work by connecting an external device to power
supply through an internal transistor in order to turn it on.
Figure 5: AUX
Inside HomeLogiX
TM