User's Manual

period. (After self check at power up the walk test is automatic
over the right side of the lens for more
ith 4 second intervals for a total transmission time of
a ely 40 seconds.
T insure clear RF pass
cont .
I will remain
announcements.
R nual for
enable for 2 minutes.)
Radio Test – Place a magnet
than 3 seconds; the red indicator illuminates. 10 Alarms events are
transmitted w
pproximat
his test is to
rol panel
es between the detector and the
n all modes the LED activate at all trouble
efer also to panel ma RF testing details.
9. Testing the Detector
The PYR-2011G PIR has a built-in walk test function where the LED of
ase as described above. The LED
e
the PIR is enabled. This test is used to check the detection of the
PIR and the coverage pattern.
To perform a walk test:
1) Ensure all of the settings in the PIR are adjusted as necessary
for the location according to the installation instructions
above.
2) Insert battery in the closed c
flashes on for 2 seconds and off for 2 seconds for a period of 1
minute. Then the LED turns off. At this point a walk test can be
performed. As default, perform a walk test of 2 minute at th
end of the self test. If more than 2 minute goes past, refer to
paragraph 3.
3) Place a magnet over the right side of the lens for 1 second
only.
4) With the LED enabled the LED flashes every time the detector
detects motion. There is a two second wait period before the
next detection.
5) It is recommended that the installer test the detection by
going over the protected area and seeing that the detection
pattern is good.
6) After 1 minute, the LED goes off. If a new walk test is needed,
go again to paragraph 3.
10. Signaling Table
The LED on the front of the PYR-2011G is used to send several signals to the user. The following table describes the signals for different
activities:
Activity LED Signal
Warm-Up The LED flashes on for 2 seconds and o
the LED stops flashing and the system i
ff for 2
s read
seconds for a period of 1 minute. If the warm-up is successful,
y for detection.
Detect Condition The LED flashes on for 2 seconds and then turns off.
PIR Problem The LED flashes on for 1 second and then off for 1 second. A PIR check is conducted every 3 hours.
Temperature Problem The LED flashes on in short bursts.
Weak Battery LED OFF and ON alternately during Alarm, Tamper event
11. Limited Warranty
ROSSLARE ENTERPRISES LIMITED S (Rosslare) ONE YEAR LIMITED WARRANTY is
applicable worldwide. This warranty supersedes any other warranty. Rosslare's ONE YEAR
LIMITED WARRANTY is subject to the following conditions:
Warranty
Warranty of Rosslare's products extends to the original purchaser (Customer) of the
red By This Warranty and Duration
Rosslare product and is not transferable.
Products Cove
the course of normal use and service. The warranty period commences with the date of
d extends for a period of 1 year (12 Months).
ROSSLARE ENTERPRISES LTD. AND / ORSUBSIDIARIES (ROSSLARE) warrants that
the PYR-2011G Advanced wireless PIR, to be free from defects in materials and assembly
in
shipment to the original purchaser an
Warranty Remedy Coverage
In the event of a breach of warranty, ROSSLARE will credit Customer with the price of the
Product paid by Customer, provided that the warranty claim is delivered to ROSSLARE by
during the warranty period in accordance with the terms of this warranty.
D. AND / OR
s not immediately required.
60) day holding period
D. AND /OR SUBSIDIARY’S sole discretion, shall become the property of ROSSLARE
AND /OR SUBSIDIARIES.
sured
duct evaluation within the sixty (60) day
$ 50.00 or equivalent charge will be
plied to each Product for labor required in the evaluation.
osslare will repair or replace, at its discretion, any product that under normal conditions of
use and service proves to be defective in material or workmanship. No charge will be
this warranty, provided that the
ork is done by Rosslare or a Rosslare authorized service center.
the Customer
Unless otherwise requested by ROSSLARE ENTERPRISES LT
SUBSIDIARIES representative, return of the failed product(s) i
thin a sixty (If ROSSLARE has not contacted the Customer wi
following the delivery of the warranty claim, Customer will not be required to return the failed
product(s). All returned Product(s), as may be requested at ROSSLARE ENTERPRISES
LT
ENTERPRISES LTD.
To exercise the warranty, the user must contact Rosslare Enterprises Ltd. to obtain an RMA
number after which, the product must be returned to the Manufacturer freight prepaid and
in
In the event ROSSLARE chooses to perform a pro
holding period and no defect is found, a minimum US
ap
R
applied for labor or parts with respect to defects covered by
w
4 0706-0960110+01