[ RX358 Series ] 3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ] User Manual FEATURES • Support up to 1000GB • Front Panel Light beam affiliated Power ON/OFF switch • Power On/Off for internal cooling fan • OS Supports Win2000/ME/XP/VISTA, and Mac OS 8.6/9.x/10.x and above and Linux kernel after 2.4.1.0 • Power: 100~240 AC Adapter with 12V/DC output • SATA to USB 2.0, backward compatible to USB 1.
.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ] User Manual Enclosure Figure Description Front View A B Rear View C E G D F A. Ventilation design 1 C. Fan Switch E. Power Jack G. eSATA Port 2 B. Ventilation design 2 D. Power Switch F.
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ] User Manual User Assembly Guide z Please follow the instructions and make sure your HDD is successfully installed to the mobile disk! STEP1: Release the 4 screws, and then remove the bottom aluminum cover.
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ] User Manual STEP2: Release 2 screws from back panel, and then slide out the side plates. STEP3: Place HDD into the enclosure properly. Connect HDD to SATA connector.
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ] User Manual STEP4: Tight up 4 screws from side to side. STEP5: Reassemble two side plates back to the enclosure and fix the screws.
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ] User Manual STEP6: Replace the aluminum cover back and tight up 4 screws. Attention 1. Make sure HDD does not dash the leaves of fan during assembly. 2. Please leave at least 5cm from air intake ventilator.
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ] User Manual HDD Formatting Guide z You may format your external HDD through USB2.0 connection. z Please make sure your external HDD is turned on and well connected to the PC before formatting the HDD. STEP1: Right-click “My Computer” icon and select the “Manage” column. STEP2: Select “Disk Management” and you will see your External HDD showed “Unallocated”.
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ] User Manual STEP3: Right-click on the “Unallocated” blocks and selects “New Partition”. STEP4: The “New Partition Wizard” will appear. instruction of the wizard to complete.
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ] User Manual STEP5: When new partition is completed, the external HDD will be recognized as a “New Volume”. STEP6: Double-click “My Computer”. volume appears on your PC.
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ] User Manual NOTICE Question：Does this SATA enclosure support hot swap? Answer：Yes, but it depends on the motherboard you have. 1. If your motherboard has an eSATA port in the Back I/O Connectors Panel as shown in picture # 1 your hot-swap function is supported and there is no need to install the eSATA bracket. All you need is connecting the enclosure with eSATA port at the back of your computer.
