Wireless Router RNX-N4PS User Manual
Wireless Router RNX-N4PS User Manual CONTENTS 1 INTRODUCTION ............................................................................................................. 2 2 KEY FEATURES .............................................................................................................. 3 3 PACKAGE CONTENTS ................................................................................................... 3 4 PRODUCT LAYOUT ................................................................
Wireless Router RNX-N4PS User Manual 1 Introduction Congratulations on your purchase of RNX-N4PS Wireless Network Broadband Router. RNX-N4PS is compliant with draft 802.11n v 2.0 up to 6 times faster than standard 802.11g based routers while still being compatible with 802.11g & 802.11b gadgets. RNX-N4PS is not only a Wireless Access Point, but also doubles as a 4-port full-duplex Ethernet Switch that connects your wired-Ethernet devices together at incredible speeds.
Wireless Router RNX-N4PS User Manual 2 Key Features Features z Incredible Data Rate up to 300Mbps** z IEEE 802.11n Compliant and backward compatible with 802.11b/g z Four 10/100 Mbps Fast Switch Ports (Auto-Crossover) z Firewall supports Virtual Server z Mapping, DMZ, IP Filter, ICMP Blocking, SPI z Support 802.1x Authenticator, 802.11i (WPA/WPA2, AES), VPN pass-through z WDS (Wireless Distribution System) ** Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used.
Wireless Router RNX-N4PS User Manual 4 Product Layout 4
Wireless Router RNX-N4PS User Manual LED z POWER：Lights up when powered ON. Blinks on TEST/RESET z WLAN：Lights up in Green, when WLAN is enabled. Blinks on traffic z LAN PORT ACTIVY：Blinks on traffic for specific LAN PORT z 100 Mbps：Lights up when 100 Mbps data rate enabled on that specific port Item z Reset：Click this button to restart the system, or press this button and hold for 10 seconds to restart the system. z WPS：Click this button to start WPS function.
Wireless Router RNX-N4PS User Manual 6 RNX-N4PS Placement You can place RNX-N4PS on a desk or other flat surface, or you can mount it on a wall. For optimal performance, place your Wireless Broadband Router in the center of your office (or your home) in a location that is away from any potential source of interference, such as a metal wall or microwave oven. This location must be close to a power connection and your ADSL/Cable modem.
Wireless Router RNX-N4PS User Manual 8 PC Network Adapter setup (Windows XP) • Enter [Start Menu] Æ select [Control panel] Æ select [Network].
Wireless Router RNX-N4PS User Manual • Select [Internet Protocol (TCP/IP)] =>Click [Properties]. • Select the [General] tab. a. RNX-N4PS supports [DHCP] function, please select both [Obtain an IP address automatically] and [Obtain DNS server address automatically].
Wireless Router RNX-N4PS User Manual 9 Bring up RNX-N4PS Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. Then, RNX-N4PS automatically enters the self-test phase. During self-test phase, Power LED will blink briefly, and then will be lit continuously to indicate that this product is in normal operation. 10 Smart Wizard CHECK • Internet connection should be setup & ready to use (ADSL or cable modem). • Modem must provide RJ45 port to connect with RNX-N4PS.
Wireless Router RNX-N4PS User Manual Click Setup Wizard to setup your RNX-N4PS router. Click User Manual to launch smart wizard user manual. Click Adobe Reader to setup Adobe Acrobat reader on your PC/Notebook. Click EXIT anytime you want to abort.
Wireless Router RNX-N4PS User Manual Click to proceed. Click to abort. RNX-N4PS should be setup as depicted above.
Wireless Router RNX-N4PS User Manual Make sure your DSL/CABLE modem is setup and working. Else take the help of your internet service provider. Click to proceed. Check the MODEM and RNX-N4PS connection. It should be as shown below.
Wireless Router RNX-N4PS User Manual Check power connection for modem as well as RNX-N4PS. Make sure antenna is connected to rear panel of RNX-N4PS. Click to proceed. Notice the LED that should be light up at this stage. If not, check your procedures again. Click to configure WAN & Wireless settings.
Wireless Router RNX-N4PS User Manual User name and password are admin/admin. Click . Your default browser will connect to RNX-N4PS Web Server http://192.168.0.1 .
Wireless Router RNX-N4PS User Manual Click to enter mode selection.
Wireless Router RNX-N4PS User Manual Select the mode that RNX-N4PS is going to be and set its configurations. AP Repeater mode does not enable WAN interface, Setup Wizard will skip WAN Configuration. Click to automatically detect your Internet Network settings.
Wireless Router RNX-N4PS User Manual Smart Wizard has detected DHCP client. Configure the host name and MAC address of your ADSL modem. Click Next to proceed. Smart Wizard has finished setting up WAN Configuration. Click to proceed.
Wireless Router RNX-N4PS User Manual To apply the entire configuration, click . NOTE: After Wireless settings are applied, you need to connect from your WLAN client with the security settings you just finished configuring. Remember the type of security & security key.
Wireless Router RNX-N4PS User Manual 11 Initial Setup RNX-N4PS RNX-N4PS uses web-interface for configuration to be accessed through your web browser, such as Internet Explorer or Netscape Communicator. - LOGIN Procedure 1. OPEN your browser (e.g. Internet Explorer). 2. Type http://192.168.0.1 in address bar and hit [Enter] button on your keyboard.
Wireless Router RNX-N4PS User Manual 3. Click to navigate into RNX-N4PS configuration home page. 4. You will see the home page of RNX-N4PS as follows.
Wireless Router RNX-N4PS User Manual - Status This page allows you to monitor the current status of your router. You can use the status page to quickly see if you have any updated firmware available (bug fixes, updates). You can navigate from this page with a few interesting options for reminding or skipping this page forever & so forth. Once you click on button to go to the requested page, you can see the status page of the RNX-N4PS.
Wireless Router RNX-N4PS User Manual LAN Settings: This section displays the Broadband router LAN port’s current LAN & WLAN information. It also shows whether the DHCP Server function is enabled / disabled.
Wireless Router RNX-N4PS User Manual WLAN Settings: This section displays the current WLAN configuration settings you’ve configured in the Wizard / Basic Settings / Wireless Settings section. Wireless configuration details such as SSID, Security settings, BSSID, Channel number, mode of operation are briefly shown. - LAN The LAN Tabs reveals LAN settings which can be altered at will. If you are an entry level user, try accessing a website from your browser.
Wireless Router RNX-N4PS User Manual LAN IP IP address: 192.168.0.1. It is the router’s LAN IP address (Your LAN clients default gateway IP address). It can be changed based on your own choice. IP Subnet Mask: 255.255.255.0 Specify a Subnet Mask for your LAN segment. 802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree function is enabled, this router will use the spanning tree protocol to prevent network loops.
Wireless Router RNX-N4PS User Manual - DHCP View the current LAN clients which are assigned with an IP Address by the DHCP-server. This page shows all DHCP clients (LAN PCs) currently connected to your network. The table shows the assigned IP address, MAC address and expiration time for each DHCP leased client. Use the button to update the available information. Hit to get the updated table. You can check “Enable Static DHCP IP“. It is possible to add more static DHCP IPs.
Wireless Router RNX-N4PS User Manual - Schedule This page allows user to set up schedule function for Firewall and Power Saving. Add schedule, edit schedule options to allow configuration of firewall and power savings services. Fill in the schedule and select type of service. Click to implement those settings.
Wireless Router RNX-N4PS User Manual The schedule table lists the pre-schedule service-runs. You can select any of them using the check box. - Event Log View operation event log. This page shows the current system log of the Broadband router. It displays any event occurred after system start up. At the bottom of the page, the system log can be saved to a local file for further processing or the system log can be cleared or it can be refreshed to get the most updated information.
Wireless Router RNX-N4PS User Manual - Monitor Show histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequently.
Wireless Router RNX-N4PS User Manual - Language This Wireless Router support multiple language of web pages, You could select your native language here.
Wireless Router RNX-N4PS User Manual 12 Wizard Click Wizard to configure the Broadband Router. Setup wizard will now be displayed; check that the modem is connected and click . The details please refer to Smart Wizard .
Wireless Router RNX-N4PS User Manual 13 INTERNET - Status This page shows the current Internet connection type and status - Dynamic IP Use the MAC address when registering for Internet service, and do not change it unless required by your ISP. If your ISP used the MAC address of the Ethernet card as an identifier, connect only the PC with the registered MAC address to the broadband router and click the button.
Wireless Router RNX-N4PS User Manual Host Name: This is optional. MAC address: The default value is set to the WAN’s physical interface of the broadband router.
Wireless Router RNX-N4PS User Manual - Static IP If your ISP Provider has assigned a fixed IP address, enter the assigned IP address, Subnet mask, Default Gateway IP address, and Primary DNS of your ISP provider.
Wireless Router RNX-N4PS User Manual Login / Password: Enter the PPPoE username and password assigned by your ISP Provider. Service Name: This is normally optional. Maximum Transmission Unit (MTU): This is the maximum size of the packets. Type: Enable the Auto-reconnect option to automatically re-establish the connection when an application attempts to access the Internet again. Idle Timeout: This is a maximum period of time for which the Internet connection is maintained during inactivity.
Wireless Router RNX-N4PS User Manual 14Wireless Settings - Basic In basic setting page, you can set wireless Radio, Mode, Band, SSID, and Channel.
Wireless Router RNX-N4PS User Manual Radio: You can turn on/off wireless radio. If wireless Radio is off, you cannot associate with AP through wireless. Mode: In this device, we support three operation modes which are AP router, AP route with WDS (we will introduce this function later section), and repeater. If you choose AP Router Mode, you can select AP or WDS function in the dropdown menu. Band: You can select the wireless standards running on your network environment. 2.
Wireless Router RNX-N4PS User Manual - WDS with AP Router Wireless Distribution System, a system that enables the wireless interconnection of access point, allows a wireless network to be expended using multiple access points without a wired backbone to like them. Each WDS APs need setting as same channel and encryption type. MAC address 1~4: Please enter the MAC address of the neighboring APs that participates in WDS, we support 4 devices now.
Wireless Router RNX-N4PS User Manual Fragment Threshold: This specifies the maximum size of a packet during the fragmentation of data to be transmitted. If you set this value too low, it will result in bad performance. RTS Threshold: When the packet size is smaller than the RTS threshold, the wireless router will not use the RTS/CTS mechanism to send this packet. Beacon Interval: is the interval of time that this wireless router broadcasts a beacon. A Beacon is used to synchronize the wireless network.
Wireless Router RNX-N4PS User Manual CTS Protection: It is recommended to enable the protection mechanism. This mechanism can decrease the rate of data collision between 802.11b and 802.11g wireless stations. When the protection mode is enabled, the throughput of the AP will be a little lower due to a lot of framenetwork that is transmitted. TX Power: This can be set to a bare minimum or maximum power.
Wireless Router RNX-N4PS User Manual enabling this feature is recommended. Disabling “Broadcast ESSID” can provide better security. WMM: Wi-Fi MultiMedia if enabled supports QoS for experiencing better audio, video and voice in applications. Encryption: When you choose to disable encryption, it is very insecure to operate RNX-N4PS. Enable 802.1x Authentication IEEE 802.1x is an authentication protocol. Every user must use a valid account to login to this Access Point before accessing the wireless LAN.
Wireless Router RNX-N4PS User Manual WEP Encryption When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to encrypt data. You can generate the key by yourself and enter it. You can enter four WEP keys and select one of them as a default key. Then the router can receive any packets encrypted by one of the four keys. Authentication Type: There are two authentication types: "Open System" and "Shared Key".
Wireless Router RNX-N4PS User Manual Key1 - Key4: The WEP keys are used to encrypt data transmitted in the wireless network. Use the following rules to setup a WEP key on the device. 64bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range) or 5-digit ASCII character as the encryption keys. 128-bit WEP: input 26-digit Hex values (in the "A-F", "a-f" and "0-9" range) or 13-digit ASCII characters as the encryption keys.
Wireless Router RNX-N4PS User Manual WPA-Radius Encryption Wi-Fi Protected Access (WPA) is an advanced security standard. You can use an external RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication. It uses TKIP or CCMP (AES) to change the encryption key frequently. Press button when you are done.
Wireless Router RNX-N4PS User Manual Enable wireless access control: Enable the wireless access control function Adding an address into the list Enter the "MAC Address" and "Comment" of the wireless station to be added and then click . The wireless station will now be added into the "Current Access Control List" below. If you are having any difficulties filling in the fields, just click "Clear" and both "MAC Address" and "Comment" fields will be cleared.
Wireless Router RNX-N4PS User Manual - Wi-Fi Protected Setup (WPS) WPS is the simplest way to establish a connection between the wireless clients and the wireless router. You don’t have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection. You only need to press a button on both wireless client and wireless router, and the WPS will do the rest for you.
Wireless Router RNX-N4PS User Manual Self Pin Code: This is the WPS PIN code of the wireless router. You may need this information when connecting to other WPS-enabled wireless devices. SSID: This is the network broadcast name (SSID) of the router. Authentication Mode: It shows the active authentication mode for the wireless connection. Passphrase Key: It shows the passphrase key that is randomly generated by the wireless router during the WPS process.
Wireless Router RNX-N4PS User Manual 15 Firewall Settings The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attacks, and defending against a wide array of common Internet attacks. However, for applications that require unrestricted access to the Internet, you can configure a specific client/server as a Demilitarized Zone (DMZ).
Wireless Router RNX-N4PS User Manual Enable DMZ: Enable/disable DMZ LAN IP Address: Fill-in the IP address of a particular host in your LAN Network that will receive all the packets originally going to the WAN port/Public IP address above. Click at the bottom of the screen to save the above configurations. - Denial of Service (DoS) The Broadband router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port Scan and Sync Flood.
Wireless Router RNX-N4PS User Manual Ping of Death: Protections from Ping of Death attack. Discard Ping From WAN: The router’s WAN port will not respond to any Ping requests Port Scan: Protects the router from Port Scans. Sync Flood: Protects the router from Sync Flood attack. - MAC Filter If you want to restrict users from accessing certain Internet applications / services (e.g. Internet websites, email, FTP etc.), and then this is the place to set that configuration.
Wireless Router RNX-N4PS User Manual Enable MAC Filtering: Check to enable or disable MAC Filtering. Deny: If you select “Deny” then all clients will be allowed to access Internet accept for the clients in the list below. Allow: If you select “Allow” then all clients will be denied to access Internet accept for the PCs in the list below. Add PC MAC Address Fill in “LAN MAC Address” and of the PC that is allowed to access the Internet, and then click .
Wireless Router RNX-N4PS User Manual - IP Filter Enable IP Filtering: Check to enable or disable IP Filtering. Deny: If you select “Deny” then all clients will be allowed to access Internet accept for the clients in the list below. Allow: If you select “Allow” then all clients will be denied to access Internet accept for the PCs in the list below. Add PC IP Address You can click PC to add an access control rule for users by an IP address or IP address range.
Wireless Router RNX-N4PS User Manual - URL Filter You can block access to some Web sites from particular PCs by entering a full URL address or just keywords of the Web site. Enable URL Blocking: Enable or disable URL Blocking Add URL Keyword Fill in “URL/Keyword” and then click . You can enter the full URL address or the keyword of the web site you want to block. If you happen to make a mistake and want to retype again, just click "Reset" and the field will be cleared.
Wireless Router RNX-N4PS User Manual 16 Advanced Settings - Network Address Translation (NAT) Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public IP Addresses. NAT provides Firewall protection from hacker attacks and has the flexibility to allow you to map Private IP Addresses to Public IP Addresses for key services such as Websites and FTP. Select Disable to disable the NAT function.
Wireless Router RNX-N4PS User Manual Enable Port Mapping: Enable or disable port mapping function. Description: description of this setting. Local IP: This is the local IP of the server behind the NAT firewall. Type: This is the protocol type to be forwarded. You can choose to forward “TCP” or “UDP” packets only, or select “BOTH” to forward both “TCP” and “UDP” packets. Port Range: The range of ports to be forward to the private IP.
Wireless Router RNX-N4PS User Manual Remove Port Mapping If you want to remove a Port Mapping setting from the "Current Port Mapping Table", select the Port Mapping setting that you want to remove in the table and then click D. If you want to remove all Port Mapping settings from the table, click button. Click will clear your current selections. Click at the bottom of the screen to save the above configurations.
Wireless Router RNX-N4PS User Manual Enable Port Forwarding: Enable or disable Port Forwarding. Description: The description of this setting. Local IP / Local Port: This is the LAN Client/Host IP address and Port number that the Public Port number packet will be sent to. Type: Select the port number protocol type (TCP, UDP or both). If you are unsure, then leave it to the default “both” setting.
Wireless Router RNX-N4PS User Manual Enable Trigger Port: Enable or disable the Port Trigger function. Trigger Port: This is the outgoing (Outbound) range of port numbers for this particular application. Trigger Type: Select whether the outbound port protocol is “TCP”, “UDP” or “BOTH”. Public Port: Enter the In-coming (Inbound) port or port range for this type of application (e.g.
Wireless Router RNX-N4PS User Manual Remove Port Triggering If you want to remove Special Application settings from the "Current Trigger-Port Table", select the Port Triggering settings you want to remove in the table and then click . If you want remove all Port Triggering settings from the table, just click the button. Click will clear your current selections. - Application Layer Gateway (ALG) You can select applications that need ALG support.
Wireless Router RNX-N4PS User Manual Enable/Disable UPnP: You can enable or Disable the UPnP feature here. After you enable the UPnP feature, all client systems that support UPnP, like Windows XP, can discover this router automatically and access the Internet through this router without having to configure anything. The NAT Traversal function provided by UPnP can let applications that support UPnP connect to the internet without having to configure the virtual server sections.
Wireless Router RNX-N4PS User Manual Port-based Qos This is hardware port-based QoS control method. It will limit the packets throughput in LAN1~4, WAN port. Enable Port-based QoS: Check this to enable port-based QoS functionality for the LAN/WAN port. You can also uncheck to disable. Priority: High or Low priority level of the transmit packets. Ingress Rate: The throughput limit of receiving packets. Egress Rate: The throughput limit of sending packets.
Wireless Router RNX-N4PS User Manual Unlimited Priority Queue: The LAN IP address will not be bounded in the QoS limitation. High/Low Priority Queue: This can put the packets in the protocol and port range to High/Low QoS Queue. Bandwidth Allocation: This can reserve / limit the throughput of specific protocols and port range. You can set the upper bound and Lower bound.
Wireless Router RNX-N4PS User Manual Type: Specify the direction of packets. Upload or download. IP range: Specify the IP address range. You could also fill one IP address Protocol: Specify the packet type. The default ALL will put all packets in the QoS priority Queue. Port range: Specify the Port range. You could also fill one Port. Policy: Specify the policy the QoS, Min option will reserve the selected data rate in QoS queue. Max option will limit the selected data rate in QoS queue.
Wireless Router RNX-N4PS User Manual - Routing You can set enable Static Routing to let the router forward packets by your routing policy. Destination LAN IP: Specify the destination LAN IP address of static routing rule. Subnet Mask: Specify the Subnet Mask of static routing rule. Default Gateway: Specify the default gateway of static routing rule. Hops: Specify the Max Hops number of static routing rule. Interface: Specify the Interface of static routing rule.
Wireless Router RNX-N4PS User Manual 17 TOOLS Settings - Admin You can change the password required to log into the broadband router's system webbased management. By default, the password is: admin. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive. Current Password: Fill in the current password to allow changing to a new password.
Wireless Router RNX-N4PS User Manual Port: The port number of the remote management web interface. Enabled: Check to enable the remote management function. Click at the bottom of the screen to save the above configurations. - Time The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions such as Log entries and Firewall settings. Time Zone: Select the time zone of the country you are currently in.
Wireless Router RNX-N4PS User Manual - DDNS DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name from the DDNS service providers. This router supports DynDNS, TZO and other common DDNS service providers. Enable/Disable DDNS: Enable or disable the DDNS function of this router Server Address: Select a DDNS service provider Host Name: Fill in your static domain name that uses DDNS.
Wireless Router RNX-N4PS User Manual - Power Saving power in WLAN/Ethernet mode can be enabled/disabled in this page. - Diagnosis This page could let you diagnosis your current network status.
Wireless Router RNX-N4PS User Manual - Firmware This page allows you to upgrade the router’s firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page. You can also use the Browse button to find the firmware file on your PC.
Wireless Router RNX-N4PS User Manual Backup Settings: This can save the Broadband router current configuration to a file named "config.bin" on your PC. You can also use the button to restore the saved configuration to the Broadband router. Alternatively, you can use the "Restore to Factory Defaults" tool to force the Broadband router to perform a power reset and restore the original factory settings.
Wireless Router RNX-N4PS 18 User Manual Repeater Mode Repeater mode has limited settings compared to the AP mode. Choose “Repeater mode” on the top right corner of the configuration page. System restarts and connects to the IP address http://192.168..0.1 You will see the configuration homepage under “REPEATER” mode now. - Status System status section allows you to monitor the current status of your router.
Wireless Router RNX-N4PS User Manual LAN Settings: This page displays the Broadband router LAN port’s current LAN & WLAN information. It also shows whether the DHCP Server function is enabled / disabled. Wireless configuration details such as SSID, Security settings, BSSID, Channel number, mode of operation are briefly shown. WLAN Settings: View Broadband router’s current configuration settings.
Wireless Router RNX-N4PS User Manual - Schedule Add schedule, edit schedule options allow configuration of power savings services. Fill in the schedule and select type of service. Click to implement the settings. The schedule table lists the pre-schedule service-runs. You can select any of them using the check box. - Event Log View operation log of RNX-N4PS. This page shows the current system log of the Broadband router. It displays any event occurred after system start up.
Wireless Router RNX-N4PS User Manual - Monitor Show the network packets histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequently.
Wireless Router RNX-N4PS User Manual - Language This Wireless Router support multiple language of web pages, you could select your native language here. -Basic You can set parameters that are used for the wireless stations to connect to this router. The parameters include Mode, ESSID, Channel Number and Associated Client.
Wireless Router RNX-N4PS User Manual Radio: Enable or Disable Wireless function Band: Allows you to set the AP fixed at 802.11b, 802.11g or 802.11n mode. You can also select B+G mode to allow 802.11b and 802.11g clients at the same time. Enable ESSID: You can specify the maximum ESSID number. ESSID1~3: Allow you to specify ESSID of WLAN. Site Survey: You can scan the current Wireless Access Point and connect on it. -Clint List - Tools This section has many useful and miscellaneous features.
Wireless Router RNX-N4PS User Manual - Admin You can change the password required to log into the broadband router's system webbased management. By default, the password is: admin. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive. Current Password: Fill in the current password to allow changing to a new password.
Wireless Router RNX-N4PS User Manual Enabled: Check to enable the remote management function. Click at the bottom of the screen to save the above configurations. - Time The Time Zone allows your router to reference or base its time on the settings configured here, which will affect functions such as Event Log entries and Schedule settings. Time Zone: Select the time zone of the country you are currently in. The router will set its time based on your selection.
Wireless Router RNX-N4PS User Manual - Power Saving power in WLAN/Ethernet mode can be enabled / disabled in this page. - Diagnosis This page could let you diagnosis your current network status.
Wireless Router RNX-N4PS User Manual - Firmware This page allows you to upgrade the router’s firmware. To upgrade the firmware of your Broadband router, you need to download the firmware file to your local hard disk, and enter that file name and path in the appropriate field on this page. You can also use the Browse button to find the firmware file on your PC.
Wireless Router RNX-N4PS User Manual Restore Settings: This can save the Broadband router current configuration to a file named "config.bin" on your PC. You can also use the button to restore the saved configuration to the Broadband router. Alternatively, you can use the "Restore to Factory Defaults" to force the Broadband router to perform a power reset and restore the original factory settings. - Reset You can reset the broadband router when system stops responding correctly or stop functions.
Wireless Router RNX-N4PS User Manual Appendix A – FCC Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
