AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual REV1.0.
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
CONTENTS Package Contents..................................................................................................... 1 Chapter 1. Introduction ......................................................................................... 2 1.1 Overview of the Router............................................................................................... 2 1.2 Conventions ............................................................................................................... 3 1.
4.7.1 Basic Settings ............................................................................................... 50 4.7.2 WPS ............................................................................................................. 53 4.7.3 Wireless Security .......................................................................................... 55 4.7.4 Wireless MAC Filtering ................................................................................. 59 4.7.5 Wireless Advanced ....
4.16.2 System Routing Table ................................................................................. 102 4.17 Bandwidth Control .................................................................................................. 103 4.18 IP & MAC Binding................................................................................................... 104 4.18.1 Binding Settings .......................................................................................... 104 4.18.2 ARP List.............
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Package Contents The following items should be found in your package: RNX-AC750RT AC750 Wireless Dual Band Gigabit Router DC Power Adapter for RNX-AC750RT AC750 Wireless Dual Band Gigabit Router Quick Installation Guide Resource CD for RNX-AC750RT AC750 Wireless Dual Band Gigabit Router, including: • This Guide • Other Helpful Information Note: Make sure that the package contains the above items.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Chapter 1. Introduction 1.1 Overview of the Router The RNX-AC750RT AC750 Wireless Dual Band Gigabit Router integrates 4-port Switch, Firewall, NAT-router and Wireless AP. The AC750 Wireless Dual Band Gigabit Router delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the users demanding higher networking performance.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 1.2 User Manual Conventions The router or RNX-AC750RT mentioned in this guide stands for RNX-AC750RT AC750 Wireless Dual Band Gigabit Router without any explanation. 1.3 Main Features Complies with IEEE 802.11ac. One 10/100/1000M Auto-Negotiation RJ45 WAN port, four 10/100/1000M Auto-Negotiation RJ45 LAN ports, supporting Auto MDI/MDIX. Provides USB ports supporting storage/FTP/Media.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 1.4 User Manual Panel Layout 1.4.1 The Front Panel Figure 1-1 LEDs on the front panel The router’s LEDs are located on the front panel (View from left to right). Name (Power) (Wireless) (Ethernet) (Internet) (USB) (WPS) Status Indication Off Power is off. On Power is on. Off The wireless function is disabled. On The wireless function is enabled. The router is working on 2.4GHz or 5GHz or both radio band.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 1.4.2 User Manual The Rear Panel WPS Wi-Fi Reset WAN LAN1 LAN2 LAN3 LAN4 USB ON/ OFF POWER Figure 1-2 Rear Panel sketch The following parts are located on the rear panel (View from left to right). WPS/Reset: Pressing this button for less than 5 seconds enables the WPS function.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual LAN (1, 2, 3, 4): These ports (1, 2, 3, 4) connect the router to the local PC(s). USB: The USB port connects to a USB storage device. ON/OFF: The switch for the power. POWER: The Power socket is where you will connect the power adapter. Please use the power adapter provided with this RNX-AC750RT AC750 Wireless Dual Band Gigabit Router. Wireless antenna: To receive and transmit the wireless data.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Chapter 2. Connecting the router 2.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual the router, please make sure your computer is NOT connected to any other wireless network.) Figure 2-1 Hardware Installation Figure 2-2 USB Installation Note: If you want to use the router to share files, plug the USB storage device to the USB port.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your AC750 Wireless Dual Band Gigabit Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the router is 192.168.1.1 and the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 3-2 Failure result of Ping command Please check the connection following these steps: 1. Is the connection between your PC and the router correct? Note: The Ethernet LED on the router and LEDs on your PC's adapter should be lit. 2. Is the TCP/IP configuration for your PC correct? Note: If the router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 3-4 Login Windows Note: If the above screen does not pop up, it means that your Web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it. 2. After successful login, the Quick Setup page will appear for you to quickly configure your router. Figure 3-5 Quick Setup 3.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 3-6 WAN Connection Type The router provides Auto-Detect function and supports five types of WAN connection: Dynamic IP, Static IP, PPPoE, L2TP, and PPTP. It’s recommended that you make use of the Auto-Detect function. If you are sure of what kind of connection type your ISP provides, you can select the very type and click Next to go on configuring. 4.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 3-7 Quick Setup – MAC Clone 2) If the connection type detected is Static IP, the next screen will appear as shown in Figure 3-8. Configure the following parameters and then click Next to continue. Figure 3-8 Quick Setup - Static IP IP Address - This is the WAN IP address as seen by external users on the Internet (including your ISP). Your ISP will provide you with the IP address you need to enter here.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Secondary DNS Server-（Optional） If your ISP provides another DNS server, enter it into this field. 3) If the connection type detected is PPPoE, the next screen will appear as shown in Figure 3-9. Configure the following parameters and then click Next to continue. Figure 3-9 Quick Setup – PPPoE User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Username/Password - Enter the Username and Password provided by your ISP. These fields are case-sensitive. If you have difficulty with this process, please contact your ISP. Select Static IP if the IP Address/ Subnet Mask/ Gateway and DNS server address have been provided by your ISP. Then please enter server IP address or domain name provided by your ISP, and also enter the corresponding parameters.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Username/Password - Enter the Username and Password provided by your ISP. These fields are case-sensitive. If you have difficulty with this process, please contact your ISP. Select Static IP if the IP Address/ Subnet Mask/ Gateway and DNS server address have been provided by your ISP. Then please enter server IP address or domain name provided by your ISP, and also enter the corresponding parameters.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual 5GHz - This band is less crowded and is used for time-sensitive music, video streaming or gaming. Using this band can avoid interference with 2.4GHz networks or noisy devices like cordless phones and microwave ovens. 6. Configure the basic parameters for 2.4GHz wireless network in the following screen as shown in Figure 3-13, and then click Next. Figure 3-13 Quick Setup – Wireless 2.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Disable Wireless Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the router without encryption. The above settings are only for basic wireless parameters. For advanced settings, please check “More Advanced Wireless Settings”, and then you can set the following parameters. Band - This field displayed the operating frequency being configured.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 3-14 Quick Setup – Wireless 5GHz Wireless Network Name - Also called the SSID (Service Set Identification). Enter a value of up to 32 characters. The same name must be assigned to all wireless devices in your network. The default SSID is set to be Rosewill_5GHz_XXXXXX. This value is case-sensitive. For example, TEST is NOT the same as test. Region - Select your region from the drop-down list.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT Band - This field displayed the operating frequency being configured. Mode - This field determines the wireless mode which the router works on. User Manual 11an mixed - Select if you are using both 802.11a and 802.11n wireless clients. 11a/n/ac mixed – Select if you are using 802.11a, 802.11n and 802.11ac wireless clients. Channel Width - Select any channel width from the drop-down list.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT Figure 3-15 Quick Setup - Confirm 9. Click the Finish button to complete the Quick Setup.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Chapter 4. Configuring the router This chapter will show each key function of the Web page and its configuration method. 4.1 Login After your successful login, you will see the main menus on the left of the Web-based utility. On the right, there are the corresponding explanations and instructions. The detailed explanations for each Web page’s key function are listed below. 4.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT Figure 4-1 Status - 23 - User Manual
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 4.3 User Manual Quick Setup Please refer to 3.2 Quick Installation Guide. 4.4 Network Figure 4-2 the Network menu There are three submenus under the Network menu (shown in Figure 4-2): WAN, LAN and MAC Clone. Click any of them, and you will be able to configure the corresponding function. 4.4.1 WAN Choose menu “Network → WAN”, you can configure the IP parameters of the WAN on the screen below. 1.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters. If you want to do some advanced configurations, please click the Advanced button. MTU(Bytes) - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-4 WAN - Static IP IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. Gateway - (Optional) Enter the gateway IP address in dotted-decimal notation provided by your ISP.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-5 WAN - PPPoE PPP Username/PPP Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Secondary Connection - It’s available only for PPPoE Connection. If your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network, then you can check the radio button of Dynamic/Static IP to activate this secondary connection.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Dynamic IP - You can check this radio button to use Dynamic IP as the secondary connection to connect to the local area network provided by ISP. Static IP - You can check this radio button to use Static IP as the secondary connection to connect to the local area network provided by ISP. Connection Mode-choose the Internet connection mode. Always on - In this mode, the Internet connection will be active all the time.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual DNS/Secondary DNS - If your ISP does not automatically assign DNS addresses to the router during login, please click “Set DNS server manually” check box and enter the IP address of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it as well. Click the Save button to save your settings. 4. If your ISP provides BigPond Cable (or Heart Beat Signal) connection, please select BigPond Cable.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual MTU(Bytes)- The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU value unless required by your ISP. Enable IGMP Proxy - IGMP (Internet Group Management Protocol) is used to manage multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for client devices, such as the modem router.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-7 WAN - L2TP Username/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Addressing Type - Choose the addressing type given by your ISP, either Dynamic IP or Static IP. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. MTU(Bytes) - The default MTU size is “1460” bytes, which is usually fine.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Always on - In this mode, the Internet connection will be active all the time. Connect on Demand - You can configure the router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-8 PPTP Settings Username/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Dynamic IP/ Static IP - Choose the addressing type given by your ISP, either Dynamic IP or Static IP, and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Enable IGMP Proxy - IGMP (Internet Group Management Protocol) is used to manage multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for client devices, such as the modem router. The default value is enabled, and if you are not sure, please contact your ISP or just leave it. Connection Mode-choose the Internet connection mode.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual The router cannot detect PPTP/L2TP/Big Pond connections with your ISP. If your ISP uses one of these protocols, then you must configure your connection manually. 4.4.2 LAN Choose menu “Network → LAN”, you can configure the IP parameters of the LAN on the screen as below. Figure 4-9 LAN Settings MAC Address - The physical address of the router, as seen from the LAN. The value can't be changed.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-10 MAC Clone Some ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here. WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX:XX:XX:XX:XX:XX format (X is any hexadecimal digit).
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual 2.4GHz (802.11b/g/n) - Click the box, and then the router will only work in 2.4GHz frequency. You can use the 2.4GHz band to connect to many classic wireless devices like gaming consoles, laptops, DVRs, etc. 5GHz (802.11a/n/ac) - Click the box, and then the router will only work in 5GHz frequency. This band is less crowded and is used for time-sensitive music, video streaming or gaming. Using this band can avoid interference with 2.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-13 Wireless Settings – 2.4GHz Wireless Network Name - Also called the SSID (Service Set Identification). Enter a value of up to 32 characters. The same name must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be Rosewill_2.4GHz_XXXXXX. This value is case-sensitive. For example, TEST is NOT the same as test.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Note: Limited by local law regulations, version for North America does not have region selection option. Mode - Select the desired mode. 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients. 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. It is strongly recommended that you set the Mode to 802.11bgn mixed, and all of 802.11b, 802.11g, and 802.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual SSID (to be bridged) - The SSID of the AP your router is going to connect to as a client. You can also use the search function to select the SSID to join. MAC Address (to be bridged) - The BSSID of the AP your router is going to connect to as a client. You can also use the search function to select the BSSID to join. Scan - Click this button, you can search the AP which runs in the current channel.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Generate New PIN - Click this button, and then you can get a new random value for the router's PIN. You can ensure the network security by generating a new PIN. Disable device PIN - If this box is checked, and then wireless clients will not be able to connect to the wireless network with PIN code. Add device - You can add a new device to the existing network manually by clicking this button.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup process. Step 4: When the WPS LED is on, the client device has successfully connected to the router. II. Enter the client device’s PIN on the router Use this method if your client device does not have the WPS button, but has a Wi-Fi Protected Setup PIN number.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-19 Wireless Security Disable Wireless Security - If you do not want to use wireless security, check this radio button. But it’s strongly recommended to choose one of the following modes to enable security. WPA/WPA2-Personal - It’s the WPA/WPA2 authentication type based on pre-shared passphrase. The router is configured by this security type by default.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual • Encryption - When WPA-PSK or WPA is set as the Authentication Type, you can select either Automatic, or TKIP or AES as Encryption. Note: If you check the WPA/WPA2-Personal radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 4-20. Figure 4-20 WPA/WPA2 – Personal • Wireless Password - You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual • Radius Server Password - Enter the password for the Radius server. • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. WEP - It is based on the IEEE 802.11 standard. If you check this radio button, you will find a notice in red as show in Figure 4-22.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 4.6.4 User Manual Wireless MAC Filtering Choose menu “Wireless 2.4GHz → Wireless MAC Filtering”, you can control the wireless access by configuring the Wireless MAC Filtering function, shown in Figure 4-23. Figure 4-23 Wireless MAC Filtering To filter wireless users by MAC Address, click Enable. The default setting is Disabled. MAC Address - The wireless station's MAC address that you want to filter.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 1. User Manual Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX:XX:XX:XX:XX:XX (X is any hexadecimal digit). For example: 00:0A:EB:B0:00:0B. 2. Give a simple description for the wireless station in the Description field. For example: Wireless station A. 3. Select Enabled or Disabled for this entry on the Status drop-down list. 4. Click the Save button to save this entry.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 4.6.5 User Manual Wireless Advanced Choose menu “Wireless 2.4GHz → Wireless Advanced”, you can configure the advanced settings of your wireless network. Figure 4-25 Wireless Advanced Transmit Power - Here you can specify the transmit power of router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended. DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM).
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Sent Packets - Packets sent by the station You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button. If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return the previous page. Note: This page will be refreshed automatically every 5 seconds. 4.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-28 Wireless Settings – 5GHz Wireless Network Name - Also called the SSID (Service Set Identification). Enter a value of up to 32 characters. The same name must be assigned to all wireless devices in your network. Considering your wireless network security, the default SSID is set to be Rosewill_5GHz_XXXXXX. This value is case-sensitive. For example, TEST is NOT the same as test.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Note: Limited by local law regulations, version for North America does not have region selection option. Mode - Select the desired mode. 11an mixed - Select if you are using both 802.11a and 802.11n wireless clients. If you set the Mode 11an mixed, all of 802.11a and 802.11n wireless stations can connect to the router. 11a/n/ac mixed - Select if you are using a mix of 802.11a, 802.11n and 802.11ac wireless clients.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual MAC Address (to be bridged) - The BSSID of the AP your router is going to connect to as a client. You can also use the search function to select the BSSID to join. Scan - Click this button, you can search the AP which runs in the current channel. Key type - This option should be chosen according to the AP's security configuration.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Add device - You can add a new device to the existing network manually by clicking this button. If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and router using either Push Button Configuration (PBC) method or PIN method.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Use this method if your client device does not have the WPS button, but has a Wi-Fi Protected Setup PIN number. Step 1: Keep the default WPS status as Enabled and click the Add device button in Figure 4-30, then Figure 4-33 will appear. Figure 4-33 Add A New Device Step 2: Enter the PIN number from the client device in the field on the above WPS screen. Then click Connect button.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual There are five wireless security modes supported by the router: WPA-Personal, WPA2-Personal, WPA-Enterprise, WPA2-Enterprise, and WEP. Figure 4-34 Wireless Security Disable Security - If you do not want to use wireless security, check this radio button. But it’s strongly recommended to choose one of the following modes to enable security. WPA/WPA2-Personal - It’s the WPA/WPA2 authentication type based on pre-shared passphrase.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual (Pre-shared key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. • Encryption - When WPA-PSK or WPA is set as the Authentication Type, you can select either Automatic, or TKIP or AES as Encryption. Note: If you check the WPA/WPA2-Personal radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 4-35.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual • Radius Server IP - Enter the IP address of the Radius server. • Radius Server Port - Enter the port number of the Radius server. • Radius Server Password - Enter the password for the Radius server. • Group Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. WEP - It is based on the IEEE 802.11 standard.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type. Be sure to click the Save button to save your settings on this page. 4.7.4 Wireless MAC Filtering Choose menu “Wireless → MAC Filtering”, you can control the wireless access by configuring the Wireless MAC Filtering function, shown in Figure 4-23.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-39 Add or Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX:XX:XX:XX:XX:XX (X is any hexadecimal digit). For example: 00:0A:EB:B0:00:0B. 2. Give a simple description for the wireless station in the Description field. For example: Wireless station A. 3.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual 2. Select the radio button “Allow the entries specified by any enabled entries in the list to access” for Filtering Rules. 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New button. 5. Enter the MAC address 00:0A:EB:B0:00:0B /00:0A:EB:00:07:5F in the MAC Address field. 6. Enter wireless station A/B in the Description field. 7. Select Enabled in the Status drop-down list. 8. Click the Save button. 9.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 4.7.5 User Manual Wireless Advanced Choose menu “Wireless → Wireless Advanced”, you can configure the advanced settings of your wireless network. Figure 4-40 Wireless Advanced Transmit Power - Here you can specify the transmit power of router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Enable WMM - WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended. Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time. Enabled AP Isolation - This function can isolate wireless stations on your network from each other.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-42 Guest Network Wireless Settings Allow Guest To Access My Local Network - If enabled, guests can communicate with hosts.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual storage sharing servers. Guest Network Isolation -. If enabled, guests are isolated from each other. Guest Network Bandwidth Control - If enabled, the Guest Network Bandwidth Control rules will take effect. Band Select/Guest Network – Select the wireless network band (2.4G/5G) and enabled or disable its Guest Network function. Network Name - Enter a value of up to 32 characters.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-44 DHCP Settings DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network, otherwise you must configure the computer manually. Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.1.100 is the default start address.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 4.9.2 User Manual DHCP Clients List Choose menu “DHCP → DHCP Clients List”, you can view the information about the clients attached to the router in the screen as shown in Figure 4-45. Figure 4-45 DHCP Clients List Client Name - The name of the DHCP client MAC Address - The MAC address of the DHCP client Assigned IP - The IP address that the router has allocated to the DHCP client Lease Time - The time of the DHCP client leased.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual MAC Address - The MAC address of the PC for which you want to reserve an IP address. IP Address - The IP address reserved for the PC by the router. Status - The status of this entry, either Enabled or Disabled. To Reserve an IP address: 1. Click the Add New button. Then Figure 4-47 will pop up. 2. Enter the MAC address (in XX:XX:XX:XX:XX:XX format.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual There are six submenus under the USB Settings menu (shown in Figure 4-48): USB Mass Storage, User Accounts, Storage Sharing, FTP Server and Media Server. Click any of them, and you will be able to configure the corresponding functions. 4.10.1 USB Mass Storage The USB Mass Storage page provides the basic information about the USB mass storage device. Click the Refresh button to update this page. Figure 4-49 User Account Management 4.10.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-50 User Account Management Only Administrator can use a Web browser to transfer the files from a PC to the Writable shared volume on the USB drive. To add a new user account, please follow the steps below: 1. Choose the Index from the drop-down list. 2. Self-define a User Name. 3. Enter the password in the Password field. 4. Re-enter the password in the Confirm Password field. 5. Click Set to make your settings take effect.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Note: 1. Please restart the service for the new settings to take effect. 2. If you cannot use the new user name and password to access the shares, press Windows logo + R to open the Run dialog box and type net use \\192.168.1.1 /delete /yes and press Enter. (192.168.1.1 is your router's LAN IP address. If the LAN IP of the modem connected with your router is 192.168.1.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual User Access – Indicates user access of the shared folder. F stands for fully access, R stands for read-only and N stands for no-access. Status - Indicates the shared or non-shared status of the volume. Edit – Click Edit to edit the entry. To add a new folder, follow the instructions below. 1. Click Add New Folder in Figure 4-51. Figure 4-52 Add or Modify Share Folder 2.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Click the Apply button to make the settings take effect. 4.10.4 FTP Server Choose menu “USB Settings→FTP Server”, you can create an FTP server that can be accessed from the Internet or your local network. Figure 4-53 FTP Server Configuration Server Status - Indicates the FTP Server's current status. Internet Access - Select enable to allow access of the FTP server from the Internet.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 5. User Manual If WAN type is PPPoE/PPTP/L2TP, two connections will be available. Therefore, users can access FTP server via two connections. Users in a private LAN can access ftp server via Public Address while Internet users can access ftp server via Internet Address. 6. Click the Apply button to start the ftp server. To add a new folder, follow the instructions below. 1. Click Add New Folder in Figure 4-53.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-55 Media Server Setting Server Enable - Indicates the Media Server’s current status, started or stopped. You can click the Enable button to enable the Media Server and click the Disable button to disable it. Server Name - The name of this Media Server. Share Name - The display name of this folder. Folder Name - The real full path of the specified folder. Delete - You can delete the share folder by click Delete.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-57 Add New Folder Share Name - You can enter a display name for the share folder. Directory - Displays the location of this folder. Browse – Click the button to select the folder to share. Apply - Click the button to save your settings. 3. Click the Scan Now button to scan all the share folders immediately. You can also select the Auto-scan, at the same time, select an auto scan interval time by drop-down list.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-58 The Forwarding menu Enable NAT Control - If enabled, the NAT function and the Forwarding configuration will take effect. Disable NAT Control - If disabled, neither NAT function nor Forwarding configuration will take effect. Enable Hardware NAT Control - If enabled, the Hardware NAT feature will take effect. Disable Hardware NAT Control - If disabled, neither Hardware NAT feature will take effect. 4.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual when using the DHCP function. If you want the Virtual Servers configuration take effect, please make sure the NAT is enabled. Figure 4-60 Virtual Servers Service Port - The numbers of External Service Ports. You can enter a service port or a range of service ports (the format is XXX – YYY; XXX is the Start port and YYY is the End port). IP Address - The IP address of the PC running the service application.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-61 Add or Modify a Virtual Server Entry Note: It is possible that you have a computer or server that has more than one type of available service. If so, select another service, and type the same IP address for that computer or server. To modify or delete an existing entry: 1. Find the desired entry in the table. 2. Click Edit or Delete as desired on the Edit column.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-62 Port Triggering Trigger Port - The port for outgoing traffic. An outgoing connection using this port will trigger this rule. Trigger Protocol - The protocol used for Trigger Ports, either TCP, UDP, or All (all protocols supported by the router). Open Port - The port or port range used by the remote system when it responds to the outgoing request.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 6. User Manual Click the Save button to save the new rule. Figure 4-63 Add or Modify a Triggering Entry To modify or delete an existing entry: 1. Find the desired entry in the table. 2. Click Edit or Delete as desired on the Edit column. Click the Enable Selected button to make selected entries enabled. Click the Disable Selected button to make selected entries disabled.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual for a special-purpose service such as Internet gaming or videoconferencing. The router forwards packets of all services to the DMZ host. Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may be changed when using the DHCP function. Figure 4-64 DMZ To assign a computer or server to be a DMZ server: 1. Click the Enable button. 2.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual App Description - The description about the application which initiates the UPnP request. External Port - The port which the router opened for the application. Protocol - The type of protocol which is opened. Internal Port - The port which the router opened for local host. IP Address - The IP address of the local host which initiates the UPnP request. Status - Either Enabled or Disabled.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-67 Basic Security Firewall - A firewall protects your network from the outside world. Here you can enable or disable the router’s firewall. SPI Firewall - SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates that the traffic passing through the session conforms to the protocol. SPI Firewall is enabled by factory default.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual L2TP Passthrough - Layer Two Tunneling Protocol (L2TP) is the method used to enable Point-to-Point sessions via the Internet on the Layer Two level. To allow L2TP tunnels to pass through the router, click Enable. IPSec Passthrough - Internet Protocol security (IPSec) is a suite of protocols for ensuring private, secure communications over Internet Protocol (IP) networks, through the use of cryptographic security services.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-68 Advanced Security DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function. Only when it is enabled, will the flood filters be enabled. Note: Dos Protection will take effect only when the Traffic Statistics in “System Tool → Statistics” is enabled. Enable ICMP-FLOOD Attack Filtering - Enable or Disable the ICMP-FLOOD Attack Filtering.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual TCP-SYN-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current TCP-SYN-FLOOD Packets numbers is beyond the set value, the router will startup the blocking function immediately. Forbid Ping Packet From LAN Port - Enable or Disable Forbid Ping Packet From LAN Port. The default setting is disabled. If enabled, the ping packet from LAN cannot access the router.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual If your PC is blocked but you want to access the router again, use a pin to press and hold the WPS/Reset button (hole) on the back panel for about 5 seconds to reset the router’s factory defaults on the router’s Web-Based Utility. 4.13.4 Remote Management Choose menu “Security → Remote Management”, and then you can configure the Remote Management function in the screen as shown in Figure 4-70.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT Figure 4-71 Parent Control Settings Parent Control - Check Enable if you want this function to take effect.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual MAC Address of Parental PC - In this field, enter the MAC address of the controlling PC, or you can make use of the Copy to Above button below. MAC Address of Current PC - This field displays the MAC address of the PC that is managing this router. If the MAC Address of your adapter is registered, you can click the Copy to Above button to fill this address to the MAC Address of Parental PC field above.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT Figure 4-72 Parent Control Settings - 91 - User Manual
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual 4.15 Access Control Figure 4-73 Access Control There are four submenus under the Access Control menu: Rule, Host, Target and Schedule (as shown in Figure 4-73). Click any of them, and you will be able to configure the corresponding function. 4.15.1 Rule Choose menu “Access Control → Rule”, and then you can view and set Access Control rules in the screen as shown in Figure 4-74.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Schedule - Here displays the schedule selected in the corresponding rule. Enable - Here displays the status of the rule, enabled or not. Check this option to enable a specific entry. Edit - Here you can edit or delete an existing rule. Add New - Click the Add New button to add a new rule entry. Enable Selected - Click the Enable Selected button to enable selected rules in the list.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual For example: If you desire to allow the host with MAC address 00 : 11 : 22 : 33 : 44 : AA to access www.google.com only from 18:00 to 20:00 on Saturday and Sunday, and forbid other hosts in the LAN to access the Internet, you should follow the settings below: 1. Click the submenu Rule of Access Control in the left to return to the Rule List page.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-76 Host Settings Description - Here displays the description of the host and this description is unique. Address Info - Here displays the information about the host. It can be IP or MAC. Edit - To modify or delete an existing entry. Click the Delete Selected button to delete the selected entries in the table. To add a new entry, please follow the steps below. 1. Click the Add New button. 2.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-78 Add or Modify a Host Entry For example: If you desire to restrict the internet activities of host with MAC address 00:11:22:33:44:AA, you should first follow the settings below: 1. Click Add New button in Figure 4-76 to enter the Add or Modify a Host Entry page. 2. In Mode field, select MAC Address from the drop-down list. 3. In Description field, create a unique description for the host (e.g. Host_1). 4.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Edit- To modify or delete an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New button. 2. In Mode field, select IP Address, MAC Address or URL Address. 1） If you select IP Address, the screen shown is Figure 4-80. Figure 4-80 Add or Modify an Access Target Entry I) In Description field, create a unique description for the target (e.g. Target_1).
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-82 Add or Modify an Access Target Entry I) In Description field, create a unique description for the target (e.g. Target_1). II) In Add URL Address field, enter the domain name, either the full name or the keywords (for example, google) in the blank. Any domain name with keywords in it (www.google.com, www.google.cn) will be blocked or allowed. Click Add to save the address, 3. Click the Save button.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 4.15.4 User Manual Schedule Choose menu “Access Control → Schedule”, and then you can view and set a Schedule list in the next screen as shown in Figure 4-83. The Schedule list is necessary for the Access Control Rule. Figure 4-83 Schedule Settings Description - Here displays the description of the schedule and this description is unique. Edit - Here you can edit or delete an existing schedule. To add a new schedule, follow the steps below: 1.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-84 Advanced Schedule Settings For example: If you desire to restrict the internet activities of host with MAC address 00:11:22:33:44:AA to access www.google.com only from 18:00 to 20:00 on Saturday and Sunday, you should first follow the settings below: 1. Click Add New button shown in Figure 4-83 to enter the Advanced Schedule Settings page. 2. In Description field, create a unique description for the schedule (e.g. Schedule_1).
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual There are two submenus under the Advanced Routing menu as shown in Figure 4-85: Static Route List and System Routing Table. Click any of them, and you will be able to configure the corresponding function. 4.16.1 Static Route List Choose menu “Advanced Routing → Static Route List”, and then you can configure the static route in the next screen (shown in Figure 4-86).
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 3. Select Enabled or Disabled for this entry on the Status drop-down list. 4. Click the Save button to make the entry take effect. User Manual Other configurations for the entries: Click the Delete button to delete the entry. Click the Enable Selected button to enable the selected entries. Click the Disable Selected button to disable the selected entries. Click the Delete Selected button to delete the selected entries. 4.16.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual 4.17 Bandwidth Control Figure 4-89 Bandwidth Control Choose menu “Bandwidth Control”, and then you can configure the bandwidth control in the screen as shown in Figure 4-89 Bandwidth Control. You can configure the Egress Bandwidth and Ingress Bandwidth in this page. Their values you configure should be less than 100000Kbps. You can also view and configure the Bandwidth Control rules in this page.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT Status - This displays the status of the rule. Edit - Click Edit to edit the rule. Click Delete to delete the rule. User Manual To add/modify a Bandwidth Control rule, follow the steps below. 1. Click Add New shown in Figure 4-89, you will see a new screen shown in Figure 4-90. 2. Enter the information like the screen shown below. Figure 4-90 Bandwidth Control Rule Settings 3. Click the Save button. 4.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-92 Binding Setting MAC Address - The MAC address of the controlled computer in the LAN. IP Address - The assigned IP address of the controlled computer in the LAN. Bind - Check this option to enable ARP binding for a specific device. Edit - To edit or delete an existing entry.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 2. User Manual Click Edit or Delete as desired on the Edit column. 4.18.2 ARP List To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could also configure the items on the ARP list. This page displays the ARP List; it shows all the existing IP & MAC Binding entries (shown in Figure 4-94). Figure 4-94 ARP List 1.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 4.19.1 User Manual No-ip.com DDNS If the dynamic DNS Service Provider you select is www.no-ip.com, the page will appear as shown in. Figure 4-95 Figure 4-95 No-ip.com DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the Domain Name you received from dynamic DNS service provider. 2. Enter the Username for your DDNS account. 3. Enter the Password for your DDNS account. 4. Enable DDNS. 5.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-96 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the Domain Name your dynamic DNS service provider gave. 2. Enter the Username for your DDNS account. 3. Enter the Password for your DDNS account. 4. Enable DDNS. 5. Click the Login button to login the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to log out of the DDNS service.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-97 Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Enter the Domain Name you received from dynamic DNS service provider. 2. Enter the Username for your DDNS account. 3. Enter the Password for your DDNS account. 4. Enable DDNS. 5. Click the Login button to login to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual There are three submenus under the IPv6 Support menu (shown in Figure 4-98): IPv6 Status, IPv6 WAN and IPv6 LAN. Click either of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below. 4.20.1 IPv6 Status Figure 4-99 IPv6 Status The IPv6 Status page displays the router's current IPv6 status and configuration. All information is read-only.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual 4.20.2 IPv6 WAN Figure 4-100 Enable/Disable IPv6 Connection Type - Choose the correct WAN connection type based on your ISP network topology. • Dynamic IPv6 - Connections which use dynamic IPv6 address assignment. • Static IPv6 - Connections which use static IPv6 address assignment. • PPPoEv6 - Connections which use PPPoEV6 that requires a user name and password. • Tunnel 6to4 - Connections which use 6to4 address assignment.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 1) User Manual Dynamic IPv6 Figure 4-101 Dynamic IPv6 IPv6 Address - The IPv6 address assigned by your ISP dynamically. Prefix Length - The length of IPv6 address prefix. IPv6 Gateway - Enter the default gateway provided by your ISP. Addressing Type - There are two types of assignation for IPv6 address: SLAAC (Stateless address auto-configuration) and DHCPv6 (Dynamic Host Configuration Protocol for IPv6) Server.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 2) User Manual Static IPv6 Figure 4-102 Static IPv6 IPv6 Address - Enter the IPv6 address provided by your ISP. Prefix Length - The length of IPv6 address prefix. IPv6 Gateway - Enter the default gateway provided by your ISP. IPv6 DNS Server- Enter the DNS IPv6 address provided by your ISP. Secondary IPv6 DNS Server - Enter another DNS IPv6 address provided by your ISP.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-103 PPPoEv6 PPP Username/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. Authentication Type – Choose one authentication type from AUTO-AUTH, PAP, CHAP and MS-CHAP. Addressing Type - There are two types of assignation for IPv6 address: SLAAC (Stateless address auto-configuration) and DHCPv6 (Dynamic Host Configuration Protocol for IPv6) Server.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 4) User Manual Tunnel 6to4 Figure 4-104 Tunnel 6to4 This type is used in the situation that your WAN connection is IPv4 while LAN connection is IPv6. WAN Connection - Display the available wan connection. Click the Save button to save your settings. 4.20.3 IPv6 LAN Figure 4-105 IPv6 LAN Address Auto-Configuration Type - Choose the IPv6 address auto-configuration type, either RADVD or DHCPv6 Server.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual 4.21 System Tools Figure 4-106 The System Tools menu Choose menu “System Tools”, and you can see the submenus under the main menu: Time Settings, Diagnostic, Firmware Upgrade, Factory Defaults, Backup & Restore, Reboot, Password, System Log and Statistics. Click any of them, and you will be able to configure the corresponding functions. The detailed explanations for each submenu are provided below. 4.21.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Time Zone - Select your local time zone from this pull down list. Date - Enter your local date in MM/DD/YY into the right blanks. Time - Enter your local time in HH/MM/SS into the right blanks. Get From PC - Enter your PC’s current time into the right blanks.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-108 Time settings Note: 1. This setting will be used for some time-based functions such as firewall. You must specify your time zone once you login to the router successfully, otherwise, these functions will not take effect. 2. The time will be lost if the router is turned off. 3. The router will automatically obtain GMT from the Internet if it is configured accordingly. 4.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Diagnostic Tool - Check the radio button to select one diagnostic too. Ping - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. Traceroute - This diagnostic tool tests the performance of a connection. Note: You can use ping/traceroute to test both numeric IP address or domain name.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 4.21.3 User Manual Firmware Upgrade Choose menu “System Tools → Firmware Upgrade”, and then you can update the latest version of firmware for the router on the following screen. Figure 4-111 Firmware Upgrade Firmware Version - Displays the current firmware version. Hardware Version - Displays the current hardware version. The hardware version of the upgrade file must accord with the router’s current hardware version.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-112 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. The default User Name: admin The default Password: admin The default Subnet Mask: 255.255.255.0 Note: All changed settings will be lost when defaults are restored. 4.21.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual The current configuration will be covered with the uploading configuration file. Wrong process will lead the device unmanaged. The restoring process lasts for 20 seconds and the router will restart automatically then. Keep the power of the router on during the process, in case of any damage. 4.21.6 Reboot Choose menu “System Tools → Reboot”, and then you can click the Reboot button to reboot the router via the next screen.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual It is strongly recommended that you should change the factory default user name and password of the router, because all users who try to access the router's Web-based utility or Quick Setup will be prompted for the router's default user name and password. Note: The new user name and password must not exceed 14 characters in length and not include any spaces. Enter the new Password twice to confirm it. Click the Save button when finished.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure 4-116 Statistics Statistics Status - Enable or Disable. The default value is disabled. To enable it, click the Enable button. If it is disabled, the function of DoS protection in Security settings will be disabled. Statistics Interval （5-60） - The default value is 10. Select a value between 5 and 60 seconds in the drop-down list. The Packets Statistic interval indicates the time section of the packets statistic.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Statistics Table: IP/MAC Address Total Packets Bytes Packets Bytes ICMP Current Tx The IP and MAC address are displayed with related statistics. The total number of packets received and transmitted by the router. The total number of bytes received and transmitted by the router. The total number of packets received and transmitted in the last Packets Statistic interval seconds.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 4.22 Logout Choose ”Logout”, and you will be back to the login screen as shown in Figure 4-117.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Appendix A: FAQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the router. The telephone cord plugs into the Line port of the ADSL Modem. 3) Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 2. User Manual How do I configure the router to access Internet by Ethernet users? 1) Login to the router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by clicking “Save”. 2) Some ISPs require that you register the MAC Address of your adapter, which is connected to your cable/DSL Modem during installation.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Figure A-4 Virtual Servers Figure A-5 Add or Modify a Virtual server Entry Note: Your opposite side should call your WAN IP, which is displayed on the “Status” page. 4) How to enable DMZ Host: Log in to the router, click the “Forwarding” menu on the left of your browser, and click "DMZ" submenu. On the "DMZ" page, click Enable radio button and type your IP address into the “DMZ Host IP Address” field, using 192.168.1.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 5) User Manual How to enable H323 ALG: Log in to the router, click the “Security” menu on the left of your browser, and click “Basic Security” submenu. On the “Basic Security” page, check the Enable radio button next to H323 ALG. Remember to click the Save button. Figure A-7 Basic Security 4. The wireless stations cannot connect to the router. 1) Make sure the "Wireless Radio Band" is enabled.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed. 1. Install TCP/IP component 1) On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT 5) User Manual The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Appendix C: Specifications General Standards IEEE 802.11ac, IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.11a, IEEE 802.11e, IEEE 802.11i, IEEE 802.1X, IEEE 802.3X, IEEE 802.3, IEEE 802.3u, IEEE 802.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual Appendix D: Glossary 802.11ac - IEEE 802.11ac is a wireless computer networking standard of 802.11.This specification will enable multi-station WLAN throughput of at least 1 gigabit per second .This is accomplished by extending the air interface concepts embraced by 802.11n: wider RF bandwidth, more MIMO spatial streams, multi-user MIMO, and high-density modulation (up to 256 QAM). 802.11n - 802.11n builds upon previous 802.
AC750 Wireless Dual Band Gigabit Router RNX-AC750RT User Manual MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be transmitted. NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet. PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection.
