24-Port Gigabit Ethernet Switch RGS-1024 User Manual
4-Port Gigabit Ethernet Switch RGS-1024 User Manual COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of Rosewill Inc. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from Rosewill Inc. Copyright © 2011 Rosewill Inc.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Safety Warning • Place connecting cables carefully so that no one will step on them or stumble over them. • Always disconnect all cables from this device before servicing or disassembling. • Use ONLY an appropriate power adaptor or cord for your device.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual • Do not use the device outside, and make sure all the connections are indoors. • Do not obstruct the device ventilation slots, as insufficient airflow may harm your device. • Do not use this product near water, eg, in wet basement, or near a swimming pool. • Do not expose your device to dampness, dust or corrosive liquids. • Do not install, use, or service this device during a thunderstorm.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual Package Contents The following contents should be found in your package: ¾ One RGS-1024 Switch ¾ One power cord ¾ This User Guide ¾ Rubber footpads for Desk-mount ¾ Rack-mount kit for installing the switch in a 19-inch rack ) Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact your distributor.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual Chapter 1. Introduction of the Product This chapter describes the features of the RGS-1024 24-port Gigabit Ethernet Switch. 1.1 Overview of the Product The RGS-1024 24-port Gigabit Ethernet Switch provides you with a high-performance, low-cost, easy-to-use, seamless and standard upgrade to boost your old network to 1000Mbps. Increase the speed of your network server and backbone connections make Gigabit a reality.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual link status and activity, allowing you to quickly detect and correct problems on the network. 1.2 Features ¾ Supports IEEE 802.1p QoS ¾ Complies with standards IEEE802.3, IEEE802.3u, IEEE802.3ab ¾ 24 10/100/1000Mbps Auto-Sense RJ45 ports supporting Auto-MDI/MDIX ¾ All ports Support Full/Half Duplex transfer mode for 10/100Mbps and Full Duplex transfer mode for 1000Mbps ¾ Supports IEEE802.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual assigned a priority to. The illustration below shows how 802.1p priority queuing is implemented on the Switch. Mapping QoS on the Switch The Switch has four priority queues labeled 0, 1, 2 and 3. The untagged packets and the eight other IEEE 802.1p priority levels defined by the standard are mapped to the four class queues used on the Switch.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual Chapter 2. Installation 2.1 Mounting the Switch on a Desk Before place the Switch on a desk, attach four rubber footpads to the flutes on the Switch bottom, then lay the Switch on the desktop, where can be have as much as 5kg placed on top. Note: 1. The electrical outlet shall be installed near the device and shall be easily accessible. 2. Make sure there is free space for radiating heat and air. 3.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual Figure 2-2 Fasten the Switch in the rack 2.3 Power On RGS-1024 24-port Gigabit Ethernet Switch is powered by AC power supply. Powering on the Switch, it will automatically initialize and its LED indicators should respond as follows: 1） All of the Link/Act and 1000Mbps LED indicators will flash momentarily for one second, which represents a resetting of the system. 2） The Power indicator will light up.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual Chapter 3. Identifying External Components This Chapter describes the front panel, rear panel and LED indicators of the Switch. 3.1 Front Panel The front panel of the RGS-1024 consists of switch LED indicators, 24 10/100/1000Mbps RJ-45 ports. Figure 3-1 RGS-1024 Switch Front Panel sketch 3.2 Rear Panel The rear panel of the RGS-1024 only features a power receptacle, which is an AC power receptacle.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual of the Switch. The following section shows the LED indicators for the switch along with an explanation of each indicator. Figure 3-3 RGS-1024 Switch LEDs sketch ¾ POWER LED: This indicator will light solid red when the Switch powers up. If the LED is not lit, please check the power supply and connection.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual Appendix A: Specifications General Standards IEEE802.3 10Base-T; IEEE802.3u 100Base-TX; IEEE802.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual Transfer Method Store-and-Forward MAC Address Learning Automatically learning, automatically aging 10Base-T: 14881pps/Port Frame Filter Rate 100Base-Tx: 148810pps/Port 1000Base-T: 1488095pps/Port 10Base-T: 14881pps/Port Frame Forward Rate 100Base-Tx: 148810pps/Port 1000Base-T: 1488095pps/Port Environmental and Physical Dimensions 17.3×7.1×1.7in. (440×180×44mm) W×D×H Power Output 100-240V~ 50/60Hz 0.
24-Port Gigabit Ethernet Switch RGS-1024 User Manual Appendix B: Troubleshooting 1. The Power LED is not lit ¾ Make sure the AC power cord connected the Switch with power source properly. ¾ Make sure the power source is ON. 2. The Link/Act LED is not lit when a device is connected to the corresponding port ¾ Make sure that the cable connectors are firmly plugged into the Switch and the device. ¾ Make sure the connected device is turned on and working well.
