User Manual Rosenberger Active Das With Intelligent Antenna system User Manual IRU-O-15-091921-QF-01 (Rosenberger Active Das With Intelligent Antenna system-Radiant System) Manual Version 1.0 No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated. In any form or by any means without the prior written permission of Rosenberger Technologies Co., Ltd Copyright © 2009 Rosenberger Technology Co., Ltd. All rights reserved.
User Manual Rosenberger Active Das With Intelligent Antenna system Contents 1 Safety instructions............................................................................ 5 2 Product Overview ............................................................................. 6 2.1 General Information ......................................................................... 6 2.2 Main Features ................................................................................... 8 2.
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2.2.1 IM2U monitoring parameters............................................... 47 5.2.2.2 NEU monitoring parameters................................................. 48 5.2.2.3 IRU-O monitoring parameters ............................................. 48 5.2.3 Alarm Status ............................................................................. 49 5.2.3.1 IM2U Alarm Status .....................................................
User Manual Rosenberger Active Das With Intelligent Antenna system Revision Record Title Rosenberger Active Das With Intelligent MIMO Antenna system Document NO. Revision Description Date Writer Approved by V1.0 Initial version 2016-4-8 Gary Tracy V2.0 Update new IRU 2018-4-8 Gary Vincent V3.
User Manual Rosenberger Active Das With Intelligent Antenna system 1 Safety instructions It is important to read safety instructions before installing the equipment. These instructions are supplementary to any local safety regulations in place. In case of any conflict, local safety regulations shall prevail. Installation personnel should be qualified support personnel about safety operations and must have received training on Rosenberger equipment installation, maintenance and operations.
User Manual Rosenberger Active Das With Intelligent Antenna system 8. Assume no responsibility for use of unauthorized antennas, cables, and/or coupling devices not conforming with ERP/EIRP and/or indoor-only restrictions. 9. The device doesn’t support home/personal use, only the people who has the certification can operation the device. 10. The warning label message shown as below. 11. The device doesn’t contain any licensee contact information. 2 Product Overview 2.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 1 Radiant System Application Rosenberger RADIANT has remote control and monitoring function, and it can be self-diagnosis. In case of an external power off, RADIANT can keep sending alarm message to network management center for four hours, facilitating monitoring, configuring and maintenance. Rosenberger RADIANT is modular design, users can deploy diversified RF output rate and power supply options for various projects.
User Manual Rosenberger Active Das With Intelligent Antenna system 2.2 Main Features Complete Frequency Range Rosenberger RADIANT system can cover full band GSM&DCS&WCDAM<E frequency band. Sleek, Efficient, Compact Design The IRU-O provides an innovative design to integrate both a low power remote unit and antenna into a single package. The IRU-O can provide up to 28.
User Manual Rosenberger Active Das With Intelligent Antenna system 2.
User Manual Rosenberger Active Das With Intelligent Antenna system 2*QM Connector 2*NF Connector Figure 5 IRU-O Outline(Quad-band Cabinet) - 10 -
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 6 IRU-O Outline(Hexa-band Cabinet) - 11 -
User Manual Rosenberger Active Das With Intelligent Antenna system 2.4 Product Interface 2.4.
User Manual Rosenberger Active Das With Intelligent Antenna system TX/RX connectors). This port is service antenna port. For simplex repeater, this port is DL (downlink) input port of SISO. 2.4.
User Manual Rosenberger Active Das With Intelligent Antenna system 2.4.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 12 IRU-O Panel (Hexa-band Cabinet) Table 3 Identifier POWER OP SISO OP MIMO IM2U Interface Functional Description DC-48V input port SISO Optical Port (FC/APC type) MIMO Optical Port (FC/APC type) - 15 -
User Manual Rosenberger Active Das With Intelligent Antenna system 2.5 Equipment Layout 2.5.1 IM2U Layout The MU is constructed into a 19” shelf and 3U, it is connected via the connector located on the front and rear panel, the RF connector is N female type, and the optic connector is FC/APC type. IM2U is composed of optic module of IM2U, duplexer, control unit （contain modem）, RF control unit and a WDM. Please see the following figure.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 13 Internal layout for IM2U Table 4 Modules for IM2U Identifier 1 2 3 4 5 6,7 8 9 Function Description 900MHz,1800MHz,2100MHz Tri-band Diplexer, filter 900MHz,1800MHz,2100MHz signals Or 700MHz, 850MHz, 1900MHz Tri-band Diplexer, filter 700MHz, 850MHz, 1900MHz signals.
User Manual Rosenberger Active Das With Intelligent Antenna system 2.5.2 NEU Layout Figure 14 Table 5 Identifier 1 2 3 4 5 Internal layout for NEU Modules for NEU Function Description 2pcs optical module 1x8 2pcs optical module 1x1 Power supply, DC 90V~250V, output DC48V Power Management Module, one input port, 16 output ports Main Monitor Board (no wireless modem) 2.5.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 65 Internal layout for IRU-O Table 6 Modules for IRU-O Identifier 1 2 3 Function Description RF modules, RF signal amplify and control, has ALC, AGC function. Optical module 1x1 for SISO Optical module 1x1 for MIMO . 3 Installation 3.1 Engineering Installations Overview This chapter introduces installation and commissioning flow of equipment to help installation personnel understand the entire process.
User Manual Rosenberger Active Das With Intelligent Antenna system Workflow for installation, debugging, acceptance and handing over of the equipment is shown above Figures . The installation and commissioning workflow is as follows: 1. Engineering survey Inspect the suggested site environment to provide related data for design and engineering. 2. Engineering design Planning department shall design according to the engineering inspection results and make out relevant design comments and drawings. 3.
User Manual Rosenberger Active Das With Intelligent Antenna system It means that operation of the equipment is stable and meets all requirements. The user and Rosenberger agree upon this and sign the final acceptance certificate.
User Manual Rosenberger Active Das With Intelligent Antenna system Start Engineering Survey Engineering Design Unpacking Acceptance Hardware Installation Check and Power On Parameter settings System Tests Preliminary Acceptance Test N Y Project Completed Trial Run N Y Final Acceptance End Figure 16 Equipment Installations and Commissioning Flow - 22 -
User Manual Rosenberger Active Das With Intelligent Antenna system 3.2 Before Installation 3.2.1 Choosing a site location Make sure access is restricted to qualified personnel Install the product where power supply and feeder cable are accessible. Site location should be far away from heat source and damp environment. IRU-O should be put in a well-ventilated work area. It should be hung on the wall or ceiling to ensure being ventilated.
User Manual Rosenberger Active Das With Intelligent Antenna system as show on the following figure 9. Use four expansion bolts (M6*12) to fix the panel of the master unit. IM2U AND NEU dimensions are 440x360x132 mm and 15 kg in weight. Make sure access is restricted to qualified personnel Install the product where power supply and feeder cable are accessible. Site location should be far away from heat source and damp environment.
User Manual Rosenberger Active Das With Intelligent Antenna system 3.3.2 Installing onto the ceiling(quad-band) Figure 18 1. Installing onto the ceiling and video Using paper template to position mounting and cable passage holes, drill four 4.4mm diameter holes and cut one 23mm diameter by 37mm long oblong opening in the opening in ceiling. 2. Position IRU-O above ceiling as shown and fasten to ceiling by passing two M4X55mm flathead screws up through ceiling and threading into bosses on IRU- case.
User Manual Rosenberger Active Das With Intelligent Antenna system 3.3.3 Installing onto the ceiling (Hexa-band) Step 1 Use the tools to drill the square holes one the ceiling, as shown in figure 19, Figure 19 Step 2 Use M4 screw fit bracket A, bracket B and Bracket C together. As Shown in figure 20. Figure 20 Step 3 Use metal wire mount the bracket unit onto the ceiling keel, as shown in figure 21.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 21 Step 4 Joint the connector with system, as shown in figure 22. Figure 22 Step 5 The active module clamp on the bracket, as shown in figure 23.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 23 Step 6 Use Phillips screw driver to tighten the captive screw, as shown in figure 24 Figure 24 3.3.4 Installing onto the wall (Hexa-band) Step 1 Use the tools to drill the holes on the wall, as shown in figure 25.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 25 Step 2 The M8 expansion blot put into the hole, as shown in figure 26.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 27 Step 4 Use M8 washer, M8 spring washer and M8 nut to bracket A onto the wall, as shown in figure 28 Figure 28 Step 5.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 29 Step 6. Joint the connector with system, as shown in Figure 30. Figure 30 Step 7. The active module clamp on the bracket, as shown in Figure 31.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 31 Step 8, Use the Phillips screw driver to tighten the captive screw, as shown in figure 32 Figure 32 - 32 -
User Manual Rosenberger Active Das With Intelligent Antenna system 4 Connection This chapter introduces devices connection and antenna connection. 4.1 IM2U/NEU/IRU-O Connection Optical fiver can be used to connect IM2U with NEU. The optical connector is FC/APC. IRU-O is power supplied by NEU remotely. Hybrid cable can be used to connect NEU and IRU-O. The hybrid cable requires users to order separately. The RF input ports of IM2U is N-Female, RF cable is required to connect IM2U with BTS.
User Manual Rosenberger Active Das With Intelligent Antenna system 5 Commissioning Before commissioning, the engineer should be checking IM2U&NEU&IRU-O according to the following chart, you can be commissioning when finish checking: - 34 -
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 33 IM2U &NEU&IRU-O checking Chart - 35 -
User Manual Rosenberger Active Das With Intelligent Antenna system 5.1 Adding Device For a Radiant site, it contains IM2U, NEU and IRU-O. NEU is the sub device under IM2U, and IRU-O is the sub device under NEU. 5.1.1 Adding Device Manually Through this function, you can add a main device and its sub devices manually. Procedure Adding Device through Short-cut Button 1. Click to open the Create New Device page, as shown in Figure. Figure 34 Creating New Device Page 2.
User Manual Rosenberger Active Das With Intelligent Antenna system For the description of device, see Table. Figure 35 Configure Parameter Table7 Parameter Description of Creating New Device Parameter Description Input Method Device No. Indicates the unique code for each repeater. Enter a unique number in the text box. Sub No. It is the equipment type. When the adding device is a single device, select FF from the drop down list box. When the adding device has sub device, select 00.
User Manual Rosenberger Active Das With Intelligent Antenna system Parameter Description Input Method Phone Number Configure the phone number which is used to connect the device in remote mode. Enter the phone number in the text box. The phone number must match with the SIM install on the device. Device Factory Indicates the manufacturer of the device. Enter the manufacturer in the text box. Site Location Indicates the detailed installation address of the adding device.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 367 Slave Properties Page 4. Adding slave device. When the adding site is a repeater site, it contains two-level device, and you can add four RUs as slave device for it. Click to add RUs, as shown in Figure 21.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 37 Adding NEUs When the site is a Radiant site, it contains three-level device, and you can add NEU and IRU-O as slave device for it. The maximum of NEU or IRU-O can be set according to the actual situation. The setting in the following steps is a default value. 1.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 38 Set IRU-O Number 5. Click Save and return to the Create New Device page, as shown in Figure 23.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 39 Adding NEU 6. Click Test button to check settings whether there are ok, if not available , you may get a pop-up information as show in Figure 24.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 40 Testing Configuration for A New Device ---End - 43 -
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2 Device Management After successfully adding device, you can start to get and set the device parameters. Procedure: 1. Right-click a newly added device and then select Get MOID From Device from the short-cut menu, as shown in Figure 25.
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2.1 Device info. 5.2.1.
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2.1.2 NEU parameters Figure 43 NEU Device Parameters 5.2.1.
User Manual Rosenberger Active Das With Intelligent Antenna system Figure 44 Table 8 IRU-O Device Parameters Description of the Device information Parameter items Description Note Vender ID Supplier ID Reference Type ID Product Description Reference Device Type ID Product Number Reference Serial ID Product serial number Reference Longitude Product installation location Option item: enter the Longitude Latitude Product installation location Option item: enter the Latitude Firmware C
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2.2.2 NEU monitoring parameters Figure 46 NEU monitoring parameters 5.2.2.
User Manual Rosenberger Active Das With Intelligent Antenna system Table 9 Description of the monitoring information Parameter items Description Note Device NO. It is a site ID Enter a unique number for each site, different site need different number. IM2U: can be set the number from 1 to 254 NEU: same as the IM2U IRU: will be auto set by NEU Sub NO. Device ID Every equipment needs an ID for identifying code. IM2U: Default:0, cannot be set.
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2.3.1 IM2U Alarm Status Figure 48 IM2U Alarm Status 5.2.3.
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2.3.3 IRU-O Alarm Status Figure 50 IRU-O Alarm Status Table 10 Description of the monitoring information Parameter items Description Note Power Fail alarm If the main power supply down, will alarm. If got the alarm, it means that it has no main power supply. Power Fault alarm If the internal power supply voltage is not stable, and the voltage ripple is greater than 10%, will alarm.
User Manual Rosenberger Active Das With Intelligent Antenna system Parameter items Description Note cable to Ground. 2. Device temperature alarm If the equipment temperature is higher than setting temperature, will alarm The Device had been moved by somebody. If got the alarm ,maybe have following several status: 1. Unsuitable temperature value has be set .normally: 55℃ 2. The Device is too hot, and the fan failed if have 3. The Device’s program has something wrong.
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2.4 RF Setting Parameters 5.2.4.
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2.4.2 IRU-O RF Setting Parameters Figure 52 IRU-O RF Setting Parameters Table 11 Description of the monitoring information Parameter items Description Note Device Temperature threshold NEU’s temperature setting Normally, set the number is 55 RF Module switch IRU’s RF module switch Normally ON PA Temp.
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2.5 RF Status 5.2.5.
User Manual Rosenberger Active Das With Intelligent Antenna system 5.2.5.2 NEU RF Status Figure 54 NEU RF Status 5.2.5.
User Manual Rosenberger Active Das With Intelligent Antenna system Table 12 Description of the monitoring information Parameter items Description Note Mobile Network Code Master unit Modem parameters, only read Reference Location Area Code Master unit Modem parameters, only read Reference BTS ID Master unit Modem parameters, only read Reference RFCN/CH NO.
User Manual Rosenberger Active Das With Intelligent Antenna system 6 System Monitor Introduce Operation & maintenance terminal (OMT) interact with the Radiant to set and lookup its status and RF parameters. It can display alarms real-time. OMT can set local connection, SMS connection with the device for operation and maintenance at any time, or at any location.
FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
