5.
Table of Contents Section Title Page 1 Specification 3 2 Installation 4 3 Operation 8 4 On-Screen Displays (OSDs) 10 5 Description of wiring 12 6 Precautions 13 7 Screws included 14 2
1. Specifications, 15.4 Inch Monitor Resolution Display area Size 1280(H) × 800(V) 331.2(W) × 207.0(H) 15.4" TFT Video input Composite Video(RCA)(F) ×2 (NTSC,PAL,SECAM) Audio input Stereo Sound Input (RCA)(F) ×2 Audio output Stereo Sound output (RCA)(F) ×1 IR Transmitter 2.3MHz&2.
2. Installation Step 1: Mount the bracket above the headliner to the roof beam. IMPORTANT! The bracket is directional! Please use screws in the holes indicated to mount the bracket to the vehicle.
Step 2: Make sure that the headliner allows the monitor mounting screws to travel from the monitor to the bracket.
Step 2 continued: Car roof Mounting bracket Direction of mounting screws 6
Step 3: Mount the monitor to the bracket using the supplied screws.
3. Operation VIDEO control keys： 6 5 4 3 2 1 1. Power：When you push this button, it will turn ON or OFF the LCD power. 2. V1：Video input 1. When you push this button, it will show the picture from the source unit connected to video input 1. 3. V2：Video input 2. When you push this button, it will show the picture from the source unit connected to video input 2. 4. MENU/SELECT：When you press this key, a menu will appear. Use the + and – keys to highlight menu selections.
VIDEO remote control function： POWER：When you push this button, the LCD will turn ON or OFF. V1/V2：Pressing this key, switches between Video Inputs 1 and 2. MENU：When you press this key, a menu will appear. Use the + and – keys to highlight menu selections. When the desired selection is highlighted, press the MENU/SELECT button again to change to that selection. UP：When you push this button, you will move up in a menu, or increase the value of the setting you have selected.
DOWN：When you push this button, you will move down in a menu, or decrease the value of the setting you have selected. 4. On-Screen Displays (OSDs) OSD MENU LIST VIDEO 1 BRIGHTNESS : Adjust the Brightness of Screen.
MUTE ON : Turn Mute function on and off. VIDEO 1 MUTE ON DISPLAY MODE: Adjust the display mode to 16:9 (widescreen) , 4:3 (standard television), or 16:9 FULL (pan-and-scan). VIDEO 1 DISPLAY MODE 16:9 DEFAULT : Return to the original Setting of LCD. VIDEO 1 DEFAULT (VX.XX) SAVE AND EXIT : Save your Personal Setting and exit to Menu Mode.
5. Description of harnesses and wiring Accessories Description Power input harness: Yellow: ACC 12V(+) switched IMPORTANT! DO NOT CONNECT YELLOW TO CONSTANT 12V(+)! 1. Black: Chassis GND A/V Output harness: Yellow：video output Red：audio output(R) 2 White：audio output(L) Note: This harness is optional and not used in some installations. A/V Input harness: Note: See wire labels for Input 1 and 2 identification.
7. Precautions 1. Do not apply pressure to the LCD screen. 2. Do not get LCD wet to clean it! If you need to clean it, please use a clean damp cloth. 3. Please do not add any parts or use any accessory which is not provided from the manufacturer. 4. Don’t use or store in high temperature. (Storage 0~70℃, Operating ~60℃) 5. When you connect power, please make sure Positive and Negative are correct, or damage could result. 6. Please be careful when moving the monitor, so as not to damage the LCD. 7.
8. Screws included 1:M4×0.
