ELECTRONIC REVISION CONTROLLED Document Number 106282 Rev D
Rosen Aviation 10.6” HD Widescreen Bulkhead Display Technical Manual, 10.6” HD Widescreen Bulkhead Display © 2013 by Rosen Aviation, LLC All Rights Reserved The information contained herein is proprietary to Rosen Aviation, LLC. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written authorization from Rosen Aviation, LLC, except as allowed under copyright laws.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display Contents 1. INTRODUCTION .................................................................................................................5 1.1. System Overview ..........................................................................................................5 1.1.1. Control Options................................................................................................................. 6 1.1.2. Display Connections ........................
Rosen Aviation 10.6” HD Widescreen Bulkhead Display 6.6. Source Mode Submenu ..............................................................................................22 6.6.1. Momentary Mode ............................................................................................................ 23 6.6.2. Constant Mode ............................................................................................................... 24 7. TECHNICAL REFERENCES AND SUPPORT .............................
10.6” HD Widescreen Bulkhead Display Rosen Aviation 1. INTRODUCTION Rosen’s 10.6” bulkhead display (model 1060-001) brings stunning HD widescreen picture quality into a small aircraft’s cabin interior. Although you can use this display in standard analog systems, via Composite and/or VGA video inputs, the 3G HD-SDI input allows you to use it in high definition systems and connect directly to a Rosen Blu-ray player. This manual describes how to install these all-in-one displays onto your aircraft.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 1.1.1. Control Options Although the 10.6” display does not have a built-in IR sensor, it provides 3.3V DC @100mA output to power an external IR receiver. The IR Receiver (P/N 0500-006) and RC5 Remote Control (P/N 0500-019) (sold separately) enables control options inputs to adjust the on-screen display settings. Alternatively, you can control the 10.6” display via a cabin management system using RS-485 and/or RS-232.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 2.2. Cooling and Ventilation The 10.6 chassis does not have vent holes for conductive cooling, nor does it require any external forced-air cooling. 2.3. Electrical Requirements Nominal voltage 28VDC / .66 A Max Power Consumption: 20 W 2.4. Video Connections The 1060-001 display uses the following connectors. Figure 2 10.6 bulkhead display connections 2.5.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display 4. IR REMOTE CONTROL The 10.6” displays may use an optional remote control to adjust the on-screen display (OSD) settings. The instructions in this manual use the RC5 IR remote in describing how to navigate the OSD. Table 1 shows the RC5 IR remote layout and the button descriptions. Table 1 RC5 IR remote control How it Works SOURCE Switches between any enabled video inputs. Press the SOURCE button twice to switch inputs.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display 5. OSD MENU OPTIONS The OSD contains screen settings and options in menus and informational readouts that display over the image, as shown below. Press MENU on the remote to open the Main Menu, as shown in Section 5.1. Press the ▲▼ buttons to navigate within the menu pages. Press the ►◄ buttons to navigate between the menu page, options, and values columns. The yellow highlighted area shows the currently selected option in the menu.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display 5.2. User Menu The Main Menu opens to the screen, shown in Figure 4 (above). Highlight User and press the ► button to access the User menu options. Press ▼▲ buttons to select a User option, and then press ENTER to change its value. Source and Auto Adjust are only available in Standard Operation Mode, and Auto Adjust is active only with a VGA (RGB) source. Figure 5 User menu options 5.2.1.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display Pillar Box: A standard 4:3 source image will appear with vertical black bars on the left and right side of the image. If the image source is letterboxed, then there will also be horizontal bars at the top and bottom of the image as well. Letter Box Expanded: Expands the source video in the vertical and horizontal dimensions to fill the display screen.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 5.2.5. Auto Adjust (Available only when Operation Mode is set to Standard and the RGB source is active.) Use Auto Adjust to force the display to evaluate the RGB signals and ensure that it is interpreting them correctly. To perform an Auto Adjust within the OSD, select the option and press ENTER. (From the remote, close the OSD and press the AUTO button.) The screen will go black briefly while the signals adjust. 5.3.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 5.3.3. Reset Scheme Restores the values of the current scheme to their default settings, and it affects only the current source. Use Reset Scheme to revert to the default screen colors if the other Image Adjust options did not correct the screen quality. Select Image AdjustReset Scheme and then press ENTER. Press EXIT to close the OSD. For information about the different Scheme modes, see Section 5.2.3 on page 11. 5.3.4.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 5.3.4.1.1. Color Levels: Red, Green, Blue Setting the Color Temperature to User will make the Red, Blue, and Green options active. Each color adjusts the low-level registers of its respective color value in the picture. Select the Image AdjustAdvancedColor Temperature and press ENTER. Set Color Temperature to User, and then press ENTER.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display 5.3.4.3. Image Position Submenu (RGB only) Use the Image Position options to center an RGB picture horizontally or vertically on the screen. Note: Changing the resolution, source, or cycling power will reset any adjustments to this submenu’s settings. Select the Image AdjustAdvancedImage Position options and then press ENTER. Figure 14 Image Position option 5.3.4.3.1.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display 5.3.4.5. RGB Phase (RGB only) Use RGB Phase to adjust the default phase value used for RGB signals. Each RGB video source can have different phase values, which can result in the RGB video image appearing to jitter. RGB Phase enables you to adjust the RGB video image to eliminate jitter. From the Image AdjustAdvanced submenu, press the ▼ button to choose RGB Phase and then press ENTER to open the control bar, as shown below.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 6. TECHNICIAN MENU To protect the display from accidental or unintentional adjustments, the Technician Menu is accessible only with a special button combination. To avoid repeating this button sequence after each change, the menu remains active until you manually close it. Whenever there is a change to the OSD, exit the menu, and cycle power for the changes to be fully accepted.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 6.1. Advanced Technician Submenu This submenu provides installers and technicians more advanced controls of the image. The active video signal and the Mode MenuOperation Mode setting determine which options will appear in the Technician Advanced submenu. The only options available with SDI active Not available Additional options available with Composite active Auto Detect mode (default) Standard mode Figure 19 Technician Advanced submenus 6.1.1.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 6.1.3. 3D Comb Filter (Composite only) When set to Enabled, the display will eliminate dot crawl and some noise on stationary portions of the picture. Highlight Advanced3D Comb Filter and press ENTER. Use the ▲▼ buttons to set the option Enabled or Disabled, and then press ENTER. Select Back to return to the Technician Menu. Press EXIT when you are ready to exit the OSD. 6.1.4.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 6.2.1. Power Mode Use Power Mode to set display’s power mode to a startup state. From the Technician Menu, press the ▼ button to select Mode MenuPower Mode and then press ENTER. Use the ▲▼ buttons to set the option and then press ENTER. Options include the following: Auto On: The display always starts up in the ON state when 28V is applied (default). Auto Off: The display always starts up in the standby state when 28V is applied.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display 6.2.3. SDI Overscan Use SDI Overscan to enable or disable video overscan for SDI at 480i and 576i resolutions. When enabled, the setting cuts off a small percentage (2.5% by default) around the edges of the picture and it resizes the image to fit the full screen. When set to disabled, a zero percent overscan is applied to all SDI resolutions. You can also enable/disable this feature via the RS-232 and RS-485 protocols.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display 6.4. Network ID Use this option to specify the IR and RS-485 network addresses to control multiple displays from a single cabin management system or remote. For example, the monitor ID numbers on a universal remote correspond to the Network ID. Each display requires a unique address on the RS-485 network. Setting this address sets the value for both interfaces.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 6.6.1. Momentary Mode Momentary enables you to specify those sources that will be set to On or Off. This mode also contains an option to specify an Auto Detect source. If the source specified in the Auto Detect option is connected, the display will ignore all source commands. If Auto Detect is set to None Selected, the monitor will return to normal momentary operation. Highlight TechnicianSource Mode and press ENTER.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 6.6.2. Constant Mode Constant enables you to specify the two sources the monitor will switch between when the constant switch goes between an open state and a ground state. Highlight TechnicianSource ModeSource Select and then press ENTER. Select Constant and press ENTER. Press ▼ to select Open and then press ENTER. Select which video input will be set to open and then press ENTER. Press ▼ to select Ground and then press ENTER.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 7.1. Troubleshooting If the display does not function properly, refer to the following troubleshooting table for symptoms and possible solutions before contacting Rosen Technical Support. Note: Always use a multimeter to verify voltages. Check actual results against the requirements described in this manual.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 7.3. RTCA DO-160F Qualifications for Displays The table below shows the DO-160F compliance of the 1060-001, unless otherwise noted. Omitted categories are not applicable to these products or their expected installations. Table 4 The 10.6” display is compliant with the following DO-160F test criteria Description Temperature and Altitude Section Category 4 Ground Survival/Short-Time Operating Low Temp 4.5.1 A1 Operating Low Temperature 4.5.
10.6” HD Widescreen Bulkhead Display Rosen Aviation Description Abnormal Operating Conditions Section Category 16.6.2 Voltage Steady State (DC) 16.6.2.1 Z Momentary Under Voltage (DC) 16.6.2.3 Z Abnormal Surge Voltage (DC) 16.6.2.4 Z Voltage Spike Voltage Spike Audio Frequency Conducted Susceptibility AF Conducted Susceptibility- Power Inputs Induced Signal Susceptibility 17 17.4 A 18 18.3.1 Z 19 Magnetic Fields Induced Into Equipment 19.3.
Rosen Aviation 10.6” HD Widescreen Bulkhead Display 7.4. Supported Video Resolutions 7.4.1. VGA Resolutions 640x480p/60 VGA 800x600p/60 SVGA 1024x768p/60, 1152x864p/60 XGA 1280x768p/60 (68.250 MHz), 1280x768p/60 (79.500 MHz), 1360x768p/60 WXGA 1440x900p/60 WSXGA 1280x1024p/60 SXGA 1400x1050p/60 (101.000 MHz), 1400x1050p/60 (121.750 MHz) SXGA+ 1680x1050p/60 WSXGA+ 1600x1200p/60 UXGA 1920x1200p/60 (154 MHz) WUXGA 7.4.2.
10.6” HD Widescreen Bulkhead Display Rosen Aviation 8. DEFINITIONS 3G HD-SDI Newer, high-definition serial digital interface with a single 2.
10.6” HD Widescreen Bulkhead Display Rosen Aviation UXGA Ultra eXtended Graphics Array V Volts VDC Volts direct current VGA Video Graphics Array Vpp Volts peak-to-peak W Watts WSXGA Widescreen eXtended Graphics Array WUXGA Widescreen Ultra eXtended Graphics Array WXGA Wide eXtended Graphics Array XGA Extended Graphics Array 9. REVISION HISTORY Revision E is limited to draft or prototype documents. Revisions I, O, Q, S, X and Z are not to be used.
