C
Table of Contents Introduction and Display Overview................... 3 Display Diagram ................................................. 4 Pinouts ................................................................ 7 External Control Interface ............................................ 8 Operation ............................................................ 9 Specifications ................................................... 12 DO-160D Compliance Matrix .....................................
1020 Owen Loop South Eugene OR 97402 541-342-3802 www.rosenaviation.
Introduction and Display Overview Introduction and Display Overview Welcome to the 8402 Technical Manual for the 8.4" LCD display. This manual provides an overview of display details including: • Pinouts • Installation • Operation • Troubleshooting • Specifications The 8402 base model includes the following features: • 8.
Display diagram Display Diagram Arm Mounts Dimensions (Inches) (8402-010 configuration shown) Contact Rosen Aviation sales for other arm options 4
Display diagram 5
Display diagram Display Diagram Bulkhead Mount Dimensions (Inches) 6
Pinouts Pinouts Slimline Base Receptacle Model 0100-002 & 0100-004 Connector: 9 Pin Male D-Subminiature Positronic SDM0000Z Mate: 9 Pin Female D-Subminiature Positronic SD9F0000X Pin # 1 2 3 4 5 6 7 8 9 Monitor Signal Chassis Ground +28V DC DC Return *Conn to pin 5/Select Switch *Conn to pin 4/Select Switch Return Reserved Video Signal Input Video Ground Reserved Slimline Base Receptacle Model 0100-005 & 0100-040 Video Connector: BNC Plug, AMP 225396-8 Power Connector: Female 3 pin, .
Pinouts 8402-001 Main Connector Pinout Connector: 5W1 Combo-D MALE Mate: 5W1 Combo-D FEMALE Pin # Monitor Signal 1 2 3 4 A1 Signal A1 Shield Shell Select Switch Return +28V DC Input Select Switch DC Return Video Signal Input Video Ground Chassis Ground Note: Base Receptacles sold separately. * Note: If monitor is a select switch version then pins 4 & 5 are normally open and closed for 200 ms when the select switch is pressed.
Pinouts External Control Dimensions ( Inches) .752 2X 6-32 UNC X .188` .900 .550 3.700 .350 .100 Operation 8.
Operation Operation On Screen Display (OSD) Main Menu The On Screen Display (OSD) provides a set of menus that enable you to adjust or view monitor features. Main menu selections lead to submenus with additional choices. Press the Menu button on the switch panel to see the Main menu.
Operation Operation (Cont) Monitor Info Menu Menu option Description Life Timer Displays monitor’s minute/hour timer SW Revision Displays software revision Power On/Off Displays power cycles Source Displays current video format Temperature Menu Takes you to Temperature sub menu Back Return to Advanced menu Temperature Menu Menu option Description Current Displays monitor’s current temperature Temperature Max Temperature Displays monitor’s maximum average Temperature Min Temperature Displ
Specifications Specifications LCD Performance Screen Resolution (pixels) 640 w x 480 h Display Viewing Area 6.73 x 5.05 in Viewing Angle ( At contrast ratio 10:1 ) Horizontal ±55º Vertical +40º up -70º down Contrast Ratio 200:1 (Min) 500:1 (Typ) Backlight Lamp Life (hours) 50000 hrs Screen Brightness 360 (Min) 450cd/m2 (Typ) Mechanical Packaging Arm Mount Weight Bulkhead Weight Power Requirements (See Appropriate Drawing) 2.
8.
Troubleshooting 8402 Trouble shooting PROBLEM POSSIBLE SOLUTION No power LED does not come on • Verify that the pinout is correct . Push and hold the power switch for about one second. • Verify Monitor is fully inserted into base receptacle. No Video Displayed on screen • Verify that the pinout is correct. • Verify that the video source is on and has a tape or DVD installed. • Verify video signal at monitor end, Use an oscilloscope or another monitor.
Technician Mode Technician mode Technician mode provides the ability to customize the Menu by restricting access to specified options. This section describes how to enter and exit technician mode and how to customize the main menu. 1. Entering technician mode: Apply 28V to the monitor, wait until green light appears ( if monitor is in auto-off, press the power button ).
Technician Mode 3. Enabling/Disabling Individual Menu Items: The cursor works via the “scroll” button as in the normal menu mode. To disable a menu item, move the cursor to that line using the “scroll” button, hold the “scroll” button down for at least 5 seconds, then release it. The cursor highlight should advance to the next menu item and the word “off” should appear to the left of the disabled menu item. To enable an item that has previously been turned off, follow the same procedure as above.
17
Disclaimer All information, including illustrations, is believed to be reliable. Users and/or installers, however, should independently evaluate the suitability of each product for their application. Rosen makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use or installation.
