6.5 www. rosenaviation .com OEM SALES CORPORATE OFFICE DEALER & OPERATOR SALES 8 Shackleford Plaza, Suite 201 Little Rock, AR 72211 1-888-523-7523 Fax (501) 225-1015 1020 Owen Loop South Eugene, OR 97402 1-888-668-4955 Fax (541) 342-4912 1121 Warren Ave, Suite 240 Downers Grove, IL 60515 1-800-859-5058 Fax (630) 963-4405 Document # 9002751 Rev D 9002751 6500 Compliant to DO-160D SlimLine Model Number DISPLAY 6500 www. rosenaviation .
Table of Contents Introduction and Display Overview................... 3 Pinouts ................................................................ 4 Installation Guidelines........................................ 6 Operation ............................................................ 8 Technician Mode.....................................................14 Troubleshooting ............................................... 16 Technical Support ............................................ 17 Specifications ......
1020 Owen Loop South Eugene OR 97402 541-342-3802 www.rosenaviation.
Introduction and Display Overview Introduction and Display Overview Welcome to the 6500 Technical Manual for the 6.5" LCD display. This manual provides an overview of the following information: • Pinouts • Installation • Operation • Technician Mode • Troubleshooting • Specifications The 6500 base model includes the following features: • Two Year Warranty • 6.5” Diagonal Screen • 400 NIT Brightness • 6.91” (W) x 5.90” (H) x 1.
Pinouts Pinouts Pinout descriptions are provided to assist in the wiring process. Pay close attention to the pinout information while completing wiring connections. Warning! This Display is for Entertainment Purposes Only! Connect to the NonCritical Power Bus. Main Interface Connectors The 6.5 SlimLine has either one or two main interface connectors, depending on the SlimLine base receptacle model you purchased.
Pinouts SlimLine Base Receptacle Models: 0100-005 and 0100-040 Video Connector: BNC Jack, AMP part number 221199-5 Mating Video Connector: BNC Plug, AMP part number 221185-8 Pin # Monitor Signal BNC signal Video Signal BNC shield Video Return Power Connector: Female 3 pin, .062" Molex Mating Power Connector: Molex 03-06-2033 Mating Power Contact: Molex 02-06-2103 Pin # Monitor Signal Molex 1 +28V DC Molex 2 DC Return Molex 3 Reserved 6.
Installation Installation Guidelines The following drawings are provided to assist the installation process for your 6.5 display. Pay close attention to dimensions and rotations when considering installation requirements. Note: The dimensions listed are listed in inches.
Installation 6.
Operation Operation Ensure that when plugging the arm into the base receptacle, the set screw in the base follows the arm’s keyed slot and the connection is not forced. Slot Set Screw Use the buttons on your 6.5” Display to control screen setup and choose between video source options. Buttons and screen options are defined in this section on page 9.
Operation 6.5" Display Button Functions Display buttons are shown and defined below. Select Switch/ Menu Scroll Sub-Menu Scroll/ Increase Value Decrease Value Status LED OSD ON/OFF Power ON/OFF Select Switch/Menu Scroll: Press this button to switch between video source options , or to scroll down when viewing On Screen Display (OSD) menu options. Decrease Value: Press this button during normal operation to decrease backlight intensity.
Operation On Screen Display (OSD) Main Menu The On Screen Display (OSD) provides a set of menus that enable users to adjust or view screen setup features. Some Main menu selections lead to submenus with additional setup options. Press the OSD ON/OFF button to view the Main menu. Main menu options are described below, and then available sub-menus are listed in the tables that follow.
Operation Advanced Menu Options Select Switch Description Adjust Relay Active Time to set the time delay when pressing the Select Switch to change video sources Adjust Repeat Delay to set the time delay when pressing and holding the Select Switch to change video sources Monitor Info Scroll to this selection’s sub-menu to view monitor information (see below) Back Select this option to return to the Advanced menu Video Formats Sub-Menu Options Description NTSC/PAL/SECAM or NTSC/PAL Only Use display
Operation Monitor Info Sub-Menu Options Continued... Temperature Menu Description Scroll to this selection’s sub-menu to view monitor temperature information (shown below) Signal Level This option will show Low, Good, or High. If the signal shows Low or High, adjust the video level at the source Back Select this option to return to the Advanced menu Temperature Sub-Menu Options Description Current Temperature This option displays the most recent temperature reading within the display.
Operation Temperature Sub-Menu Options Continued... Under Temp Back Description This option displays the number of under-temperature shut downs that have occurred.
Technician Mode Technician Mode Technician mode provides the ability to customize and restrict access to the Main menu for specified options. This section describes how to enter, enable and disable options, and exit Technician mode. Entering Technician Mode Complete the following list to enter Technician mode: 1 Apply 28V to the display and wait until the status LED turns green (if the display is in auto-off, press the power ON/OFF button).
Technician Mode Enabling/Disabling Individual Menu Items Continued... Enable a menu option as follows: 1 Highlight the desired menu option. 2 Press and hold the Select switch in for 5 seconds. 3 Release the Select switch; the next option becomes highlighted and the word ON appears next to the enabled menu option. When the monitor is returned to normal mode, any items which were disabled in technician mode will no longer be available in the main menu.
Troubleshooting Troubleshooting If the monitor does not function properly, refer to the following troubleshooting table for symptoms and possible solutions before contacting Rosen field support. Notes: • Always use an oscilloscope to verify the video signal • Always use a multimeter to verify voltages • Check actual results against the requirements described in this manual PROBLEM POSSIBLE SOLUTION No power Verify that the pinout is correct . Push and hold the power switch for about one second.
Troubleshooting PROBLEM POSSIBLE SOLUTION Red LED is on Monitor is connected to 28 volts but is either switched off or is not receiving a video signal (Standby mode) An over temp or under temp occurred (see pages 11 and 12) Image is distorted Verify that the pinout is correct.
Specifications Specifications LCD Performance Screen Resolution (pixels) 640 w x 480 h Display Viewing Area 5.14 x 3.
Disclaimer Disclaimer All information, including illustrations, is believed to be reliable. Users and/ or installers, however, should independently evaluate the suitability of each product for their application. Rosen makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use or installation.
