ELECTRONIC REVISION CONTROLLED Document Number: 102031 Rev B
Rosen Aviation 17” SlimLine Display with DVI Input Technical Manual, 17” SlimLine Display with DVI Input © 2008 by Rosen Aviation, LLC All Rights Reserved The information contained herein is proprietary to Rosen Aviation, LLC. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without written authorization from Rosen Aviation, LLC, except as allowed under copyright laws.
Rosen Aviation 17” SlimLine Display with DVI Input Contents 1. INTRODUCTION AND DISPLAY OVERVIEW .................................................................4 1.1. Unpacking .................................................................................................................. 4 2. INSTALLATION GUIDELINES .........................................................................................4 2.1. Cooling and Ventilation ...................................................................
17” SlimLine Display with DVI Input Rosen Aviation 1. INTRODUCTION AND DISPLAY OVERVIEW This manual describes how to install the Rosen 17” SlimLine Display with DVI Input onto your aircraft. It contains everything you need to know to wire the display and confirm that it is functioning correctly. The display receives Composite, Analog RGB, and DVI video input. DVI input is shown as Digital RGB in the on-screen display when switching between video sources.
Rosen Aviation 17” SlimLine Display with DVI Input 2.1. Cooling and Ventilation The display is cooled by the flow of air, or natural convection. Special care must be taken with the installation to provide a proper environment for air flow. Display vents: The unit is designed with vent openings on the top, bottom, and rear surfaces. The entire top vent, and either the entire bottom or entire rear vent must be unobstructed for a minimum of one (1) inch. The vents must also be ducted to free air.
17” SlimLine Display with DVI Input Rosen Aviation 1.49 4.50 Warning! ! Front 6x 10-32 MOUNTING HOLES (BOTH SIDES) 4.50 Maximum screw penetration depth: Top .75 inches Bottom .75 inches Sides .75 inches Rear .50 inches 1.86 1.12 Figure 3 Side view with mounting holes (3 per side) Figure 4 Rear view with mounting holes Document Number: 102031 Template: 4.
17” SlimLine Display with DVI Input Rosen Aviation 3. VIDEO CONNECTIONS 3.1. Main Interface Connector The main input connector on this display is a 21W4 Male Combo D-subminiature with 17 size-20 contacts (standard density D-sub) and four size-8 coaxial contacts, mounting in a size-4 D-subminiature shell. Recommended mating connector: ITT Cannon: (P/N 9000879). Note: Backshell of main connector is Positronic D37000GEO-1023.5.
17” SlimLine Display with DVI Input Rosen Aviation 3.1.1. Main Connector Functions Signal Input/Output Description +28V, 28V Return Input Aircraft power supply IR +5V, IR GND Output Power for optional External IR receiver IR Signal Input IR receiver signal input RGB/Video Select Switch Input TTL level input. Used to select which input (RGB or Composite) is displayed. Method of selection set by DIP switches. Refer to DIP Switch Option Selection on page 10.
17” SlimLine Display with DVI Input Rosen Aviation 3.1.3.
17” SlimLine Display with DVI Input Rosen Aviation 3.2. DIP Switch Option Selection Use DIP switches located near the input connectors. See Section 3.2.1 (below) for detailed descriptions.
Rosen Aviation 17” SlimLine Display with DVI Input Momentary Ground — No DVI This mode uses the Source Select discrete input to toggle between RGB and Composite video inputs only, based on a momentary ground. This mode uses a SPST external momentary switch between ground and the RGB/Video Select (pin 6 of the 21WA4 combo connector). Each time the switch is pressed, the display will switch back and forth between the Analog RGB and Composite Video inputs whether a signal is present or not.
17” SlimLine Display with DVI Input Rosen Aviation 4. OPERATION 4.1. Front Switch Panel Features To operate the 17” SlimLine display, use the front switch panel buttons shown below. (External controller or IR remote control options are available separately.) Power Status LED Menu Select Source Power Feature How it Works Power Status LED When the LED is green, the display is on. When the LED is red, the display is in Standby Mode.
17” SlimLine Display with DVI Input Rosen Aviation 4.2. On Screen Display (OSD) Main Menu The On Screen Display (OSD) provides a set of menus that enable you to adjust or view display features. Main Menu selections lead to submenus with additional choices. Press the Menu/Select button on the switch panel to open the Main Menu. Figure 5 Composite Main Menu Figure 6 RGB Digital (DVI) Main Menu To switch to different Main Menus (OSD, Utility, Auto), press the ◄► buttons on the front switch panel.
17” SlimLine Display with DVI Input Rosen Aviation 4.4. OSD Submenu Menu Option How it Works H Position Adjusts OSD horizontal position V Position Adjusts OSD vertical position OSD Timeout Adjusts time in which OSD turns off if left alone Return Returns OSD to the Main Menu 4.5.
17” SlimLine Display with DVI Input Rosen Aviation 4.6. Auto Submenu Menu Option How it Works Automatically adjusts image size in RGB modes Auto 4.7. Exit Submenu Menu Option How it Works Closes the screen. To exit menu, press ◄. Exit 5. HOT KEYS Hot keys are a quick way of adjusting brightness, contrast, picture-in-picture (PIP), and the scaling modes without going through the OSD menu.
17” SlimLine Display with DVI Input Rosen Aviation 6. TECHNICAL REFERENCES AND SUPPORT If the display does not function properly, refer to the following troubleshooting table for symptoms and possible solutions before contacting Rosen field support.
” SlimLine Display with DVI Input Rosen Aviation 7. DO-180E QUALIFICATIONS DO-160E Test criteria to which we test the 1700-003 series displays Description DO-160E Section DO-160E Category Temperature and Altitude 4.0 A1 Temperature Variation 5.0 C Humidity 6.0 A Operational Shock & Crash Safety 7.0 B Vibration 8.0 SB Explosion Proofness 9.0 N/A Waterproofness 10.0 N/A Fluids Susceptibility 11.0 N/A Sand & Dust 12.0 N/A Fungus Resistance 13.0 N/A Salt Spray 14.
17” SlimLine Display with DVI Input Rosen Aviation Weight 7.9 lbs ± 5% Installed Dimensions 15.32” (W) x 12.72” (H) x 1.49” (D) [389.1 mm (W) x 323.1 mm (H) x 37.8 mm (D)] Power Requirements 28V DC 40W max Operating Temperature 0ºC - 50ºC Warranty 2-year 8. REVISION HISTORY Revision Date Revision Description EC # A 11/26/08 Initial Release 08516 B TBD Update PIP information in Section 5, add note to sections 4.3 and 4.5 09250 Document Number: 102031 Template: 4.
