7 www. rosenaviation .com OEM SALES CORPORATE OFFICE DEALER & OPERATOR SALES 8 Shackleford Plaza, Suite 201 Little Rock, AR 72211 1-888-523-7523 Fax (501) 225-1015 1020 Owen Loop South Eugene, OR 97402 1-888-668-4955 Fax (541) 342-4912 1121 Warren Ave, Suite 240 Downers Grove, IL 60515 1-800-859-5058 Fax (630) 963-4405 Document # 9003050 Rev C 9003050 1710 Compliant to DO-160D Fold Down Model Number DISPLAY 1710 www. rosenaviation .
Table of Contents Introduction and Display Overview................... 3 Pinouts ................................................................ 4 Main Interface Connector .............................................. 4 Optional External Control Connector ............................. 5 Installation Guidelines........................................ 6 Operation .......................................................... 13 Main Menu .................................................................
1020 Owen Loop South Eugene, OR 97402 541-342-3802 www.rosenaviation.
Introduction and Display Overview Introduction and Display Overview Welcome to the 1710 Technical Manual for the 17" Fold Down LCD Display.
Pinouts Pinouts Pinout descriptions are provided to assist in the wiring process. Pay close attention to the pinout information while completing wiring connections. Warning! This display is for entertainment purposes only! Connect to noncritical power bus. Main Interface Connector The input connector on this monitor is a 21WA4 Male Combo D-subminiature with 17 size 20 contacts (standard density Dsub) and four Size 8 coaxial contacts, mounting in a size 4 Dsubminiature shell.
Pinouts Main Interface Connector Pinouts Continued: Pin Control Signal 13 Computer Sync Ground 14 N/C 15 N/C 16 N/C 17 N/C A1-signal Red A1-shield Red Return A2-signal Green A2-shield Green Return A3-signal Blue A3-shield Blue Return A4-signal Composite Video A4-shield Composite Video Return Back Shell Chassis Ground Optional External Control Connector The optional external controller interface is a 9-pin standard density D-subminiature male connector (part number 0300402).
Installation Guidelines Installation Guidelines The following instructions and drawings are provided to assist the installation process for your 17” Fold Down. Pay close attention to dimensions when considering installation requirements. Note: The dimensions are listed in inches.
Installation Guidelines Open the display to its fully-open position (about 160 degrees), and then turn it on its side (or turn it over) to press out the (2) pine tree clips where shown below. Save the clips for reassembly. clip locations Leave the display opened, set the assembly on its back, and remove the (4) 8-32 x 3/8 socket-head cap screws (4) corner locations (see below). Save the screws for reassembly.
Installation Guidelines Release the clip features by pulling back on the hinge region of the shroud where shown below. With the display still in its fully-opened position, carefully lift the shroud off of the frame assembly. Pull back with your fingers to release the doghouse clips, and lift as shown in the photo below. Do not stress the outer edge of the enclosure, lift only as shown below. WARNING! Do not force the shroud on or off the frame assembly.
Installation Guidelines The following drawings are also available through Rosen’s website at www.rosenaviation.com. Listed dimensions are in inches.
Installation Guidelines Page 10 Rosen Aviation Displays
Installation Guidelines Once the assembly has been mounted, plug in the harness and engage the side latch. Open the display to its fully-opened position. Carefully place the shroud back onto the frame assembly by pressing it gently into place. Press only as shown in the photo below; support the shroud with one hand and press the hinge cover “doghouse” onto the assembly. Ensure that all of the doghouse clips snap into place. Support Here Gently Press Doghouse Here Reinsert the (2) Pine Tree clips.
Installation Guidelines Adjusting the Rotation Stop: The rotation stop may be adjusted to any position from 135 degrees to 180 degrees from stowed. It may be necessary to adjust the rotation stop such that the display does not open far enough to make contact with an obstruction. There are two 6-32 socket head cap screws that need to be loosened to adjust the rotation stop; one at each end of the hinge (see photo below).
Operation Operation This Display turns on automatically when the Fold Down is in its opened position, and turns off automatically when the display is stowed. The display auto-detects an RGB signal when an RGB signal is connected to the monitor by detecting the presence of the Hsync signal (pin 8 of the 21WA4 connector). If no RGB signal is detected, the display automatically switches to composite video input whether a video signal is present or not.
Operation Picture Submenu Menu Option Description Brightness Picture Brightness Contrast Picture Contrast Phase Removes Noise in RGB Mode. Frequency Adjusts the Picture Width in RGB Mode H Position Horizontal Position Adjustment V Position Vertical Position Adjustment Sharpness Picture Sharpness Return Returns to Main Menu Note: Phase, Frequency, H Position, and V Position only appear in RGB Mode.
Operation Utility Submenu Menu Option Description Freeze Frame Freezes Picture Frame Reset Factory Reset to Default Settings Color Temperature Color Adjustment in RGB Mode Only Information Monitor Info Return Returns to Main Menu Auto Submenu Menu Option Auto Description Automatically Adjusts Image Size in RGB Mode Exit Submenu Menu Option Exit Description Exits OSD Hot Keys Hot keys are a quick way of adjusting brightness, contrast, PIP, and the scaling modes.
Troubleshooting Troubleshooting If the monitor does not function properly, refer to the following troubleshooting table for symptoms and possible solutions before contacting Rosen field support. Note: Always use an oscilloscope to verify the video signal. Always use a multimeter to verify voltages. Check actual results against the requirements described in this manual. Problem Possible Solutions No Video • Verify that the video source is on and has a tape or DVD installed.
Troubleshooting Problem Possible Solutions Image Flickers • Verify that the signal cable is secure. • Verify that the vertical frame frequency is 75 Hz or less. If using the monitor with a PC in Windows, change the Display Control Panel to 60 Hz to achieve the best performance. Image is distorted • Verify pinouts. • Verify that a signal is reaching the monitor using an oscilloscope or another monitor. • Examine the monitor for pinched or damaged cables.
Specifications Specifications LCD Performance Screen Resolution (pixels) 1280 w x 1024 h Display Viewing Area 337.9 x 270.3mm (13.30 x 10.64 inches) Viewing Angle Horizontal ±80º min, ±85º Typical Vertical ±80º min, ±85º Typical Contrast Ratio 400:1 min, 500:1 Typical Backlight Lamp Life (hours) 50,000 Screen Brightness 200 cd/m2 min, 250 Typical Mechanical Packaging Weight Power Requirements Video Performance Video Standards Graphics Standards Video input 14.4 lbs ± 5% 28V DC 40W max.
Disclaimer Disclaimer All information, including illustrations, is believed to be reliable. Users and/ or installers, however, should independently evaluate the suitability of each product for their application. Rosen makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use or installation.
