VIDEO SPLITTER™ INSTALLATION AND OPERATIONS MANUAL 10707 Stancliff Road Houston, Texas 77099 Phone (281) 933-7673 WWW.ROSE.
LIMITED WARRANTY Rose Electronics warrants the Video Splitter™ to be in good working order for one year from the date of purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good working order at any time during this one-year warranty period, Rose Electronics will, at its option, repair or replace the Unit as set forth below. Repair parts and replacement units will be either reconditioned or new. All replaced parts become the property of Rose Electronics.
TABLE OF CONTENTS Contents Disclaimer.................................................................................................. 1 About this manual ...................................................................................... 1 Introduction................................................................................................ 1 Features................................................................................................. 2 Installation – Single Unit......................
INTRODUCTION Disclaimer While every precaution has been taken in the preparation of this manual, the manufacturer assumes no responsibility for errors or omissions. Neither does the manufacturer assume any liability for damages resulting from the use of the information contained herein. The manufacturer reserves the right to change the specifications, functions, or circuitry of the product without notice.
Features Video resolution up to 1600 x 1280 Drives multiple monitors from either 1 or 2 computers Available in two, four, eight, or sixteen output models Ideal for classrooms, conference rooms, point-of-sale presentations, trading room floors, process control, security systems, airports, restaurants, and many other applications Daisy-chain units together to expand your system up to 256 monitors or more Designed for long cables distances Monitors can be located up to 250 feet away from the CPU Uses
MODELS Models (2, 4, or 8 output ports) UltraMatrix 2xE – Rear panel Model number VSP-1X2V VSP-1X4V VSP-1X8V VSP-2X2V VSP-2X4V VSP-2X8V Figure 1.
Models (16 output ports) VSP-1X16V VSP-2X16V VSP-D1X8 VSP-Q1X4 Figure 2.
INSTALLATION Installation – Single Unit The basic installation of a single Video Splitter is an easy and straightforward procedure. Perform the below steps for all computers that will be connected. It is recommended that all computers be powered off. Figure 3. Single Unit configuration The Unit in Figure 3 can be any Video Splitter model.
User operating instructions The following instructions apply to all Video Splitter models Power INPUT VGA OUTPUT VGA OUTPUT Power switch VGA OUTPUT VGA OUTPUT VGA OUTPUT OUTPUT SIGNAL I NPUT SELECT ON/OFF A / B Figure 4. Video gain switches SWITCHES: INPUT SELECT A / B This switch is used to select between the “A” or “B” VGA signal sources.
Removing the switch cover you can see the 3 banks of DIP switches. The default setting is off (all switches down). The settings are adjusted per port sequentially 1 - 4. Each bank adjusts a different color. SW4 = Red; SW5 = Green; SW6 = Blue; DIP SWITCH SETTINGS: SW4 = R SW5 = G SW6 = B These switches are used to adjust the RGB signal clarity (gain) when using higher resolutions or running extended distances. You may experiment by using these switches if your video quality is not as clear as desired.
SERVICE Service Information Maintenance and Repair This Unit does not contain any internal user-serviceable parts. In the event a Unit needs repair or maintenance, you must first obtain a Return Authorization (RA) number from Rose Electronics or an authorized repair center. This Return Authorization number must appear on the outside of the shipping container. See Limited Warranty for more information.
SAFETY Safety This Video Splitter been tested for conformance to safety regulations and requirements, and has been certified for international use. Like all electronic equipment, the Video Splitter should be used with care. To protect yourself from possible injury and to minimize the risk of damage to this Unit, read and follow these safety instructions. Follow all instructions and warnings marked on this Unit. Except where explained in this manual, do not attempt to service this Unit yourself.
Safety and EMC Regulatory Statements Safety Information Documentation reference symbol. If the product is marked with this symbol, refer to the product documentation to get more information about the product. WARNING A WARNING in the manual denotes a hazard that can cause injury or death. CAUTION A CAUTION in the manual denotes a hazard that can damage equipment. Do not proceed beyond a WARNING or CAUTION notice until you have understood the hazardous conditions and have taken appropriate steps.
Safety and EMC Regulatory Statements Informations concernant la sécurité Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la documentation du produit afin d’obtenir des informations plus détaillées. WARNING Dans la documentation, un WARNING indique un danger susceptible d’entraîner des dommages corporels ou la mort. CAUTION Un texte de mise en garde intitulé indique un danger suscep-tible de causer des dommages à ‘équipement.
APPENDICES Appendix A. General Specifications Specification Dimensions 8.85”W x 4.90”D x 2.1”H 22.5 x 12.5 x 5.3 cm. Weight 3lb. / 1.4 kg. Power 117 VAC to 17 VAC 700ma power adapter Connectors Power: DIN5 Video IN: HD15M Video OUT: HD15F Video bandwidth 250 KHz.
Appendix B. Rack mount The optional rack mount kit includes the following items: Two black anodized mounting brackets. Four 6 - 32 x 3/8” flat head mounting screws. To rack mount your Video splitter, attach the two rack mounting brackets to your Unit with the short flange against the Unit using the four screws provided. Secure the mounting brackets to the rack using the appropriate size bolts, nuts and lock washers.
〒103-0014 東京都中央区日本橋蛎殻町 1-16-11 TEL:03-3668-8089 FAX:03-3668-9872 URL:http://www.cybernetech.co.
