Owner Manual

ManualsBrandsRosalind Wheeler ManualsFurnitureSpates 57.25'' Wide Kitchen Island

Assembly Instructions - Important:

Carefully unpack and identify each component before attempting to assemble. Refer to parts list. Please take care when

assembling the unit and always set the parts on a clean, soft surface.

Spates Kitchen Island

Summary of content (9 pages)

PAGE 1
Spates Kitchen Island Assembly Instructions - Important: Carefully unpack and identify each component before attempting to assemble. Refer to parts list. Please take care when assembling the unit and always set the parts on a clean, soft surface.
PAGE 2
1. Do not use this product unless all screws and bolts are securely tightened. 2. Check that all screws and bolts are tight every three months or as needed. 3. Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation. 4. Do not use this product as a stepladder. 5. Use this product for its intended purpose only. 6. FOR INDOOR RESIDENTIAL USE ONLY.
PAGE 3
PARTS (A) Top (1 PC) (B) Drawer (2 PCS) (C) Middle Drawer (1 PC) (D) Bottom Panel (1 PC) (E) Back Panel (1 PC) (F) Shelf (2 PCS) LEFT CENTER RIGHT (G) Door (3 PCS) (H) Divider (3 PCS) (I) Hardware Pack (1 PC) (J) Left Side Panel (1 PC)
PAGE 4
PARTS (K) Right Side Panel (1 PC) (L) Partition (1 PC) (M) Table Leaf (1 PC) HARDWARE LIST NO DRAWING DESCRIPTION SIZE QUANTITY 1 Screw P6 x 19 12 PCS 2 Screw M4 x 20mm 6 PCS 3 Screw P6 x 19mm 12 PCS 4 Screw M6 x 30mm 12 PCS 5 Cam Screw 24mm 4 PCS 6 Cam Nut 15mm 4 PC 7 Shelf Pin 6 x 21mm 8 PCS 8 Knob N/A 6 PCS 9 Towel Bar N/A 2 PCS 10 Allen Wrench 4mm 1 PC Phillips Screwdriver also needed for assembly (not provided).
PAGE 5
STEP 1 CAM LOCK INSTALLATION CAMLOCK LOCKINSTALLATION INSTALLATION CAM CAM LOCK INSTALLATION (J) (5) (K) 180° 180° 180° 180° FULLY TIGHTEN ALL CAM SCREWS (5) USING PHILLIPS SCREWDRIVER (NOT PROVIDED). STEP 2 (6) (E) FULLY TIGHTEN ALL CAM LOCKS (6) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).
PAGE 6
STEP 3 (K) (E) (4) (D) FULLY TIGHTEN ALL SCREWS (4) USING ALLEN WRENCH (10). STEP 4 (E) (L) (6) (4) (J) (D) FULLY TIGHTEN ALL CAM LOCKS (6) USING PHILLIPS SCREWDRIVER (NOT PROVIDED). FULLY TIGHTEN ALL SCREWS (4) USING ALLEN WRENCH (10).
PAGE 7
STEP 5 (A) (M) (3) FULLY TIGHTEN ALL SCREWS (3) USING PHILLIPS SCREWDRIVER (NOT PROVIDED). STEP 6 (A) (4) FULLY TIGHTEN ALL SCREWS (4) USING ALLEN WRENCH (10).
PAGE 8
STEP 7 (F) (1) (7) (9) FULLY TIGHTEN ALL SCREWS (1) USING PHILLIPS SCREWDRIVER (NOT PROVIDED).
PAGE 9
STEP 9 (8) (2) (G) RIGHT SLIDE DOWN CENTER LEFT LEVELER FULLY TIGHTEN ALL SCREWS (2) USING PHILLIPS SCREWDRIVER (NOT PROVIDED). IF NEEDED, ADJUST LEVELERS TO LEVEL.