Installation Guide

RUBBER TILE
TECHNICAL DATA SHEET
09.01.2017 | Page 2
Roppe Corporation | 1602 N. Union St. - Fostoria, OH 44830 | (800) 537 - 9527
raised design
Rubber Tile
Style #991, #992, #993, #994, #995, #996 & #LB996
Color Group:
Finish:
Nominal Dimensions:
Nominal Thickness:
Weight Per Tile:
Carton Quantity:
Solid
Striped (Warning Tile)
24" x 24" (60.9 cm)
1/8" (3.175 mm)
4.5 lbs.
10 Tiles (40 sq. ft.)
Style #953
Color Group:
Finish:
Nominal Dimensions:
Nominal Thickness - #LB996:
Nominal Thickness - All Others:
Weight Per Tile - #LB996:
Weight Per Tile - All Others:
Carton Quantity - #LB996:
Carton Quantity - All Others:
Solid
Raised
19 11/16" x 19 11/16" (50 cm)
13/64" (5.16 mm)
1/8" (3.175 mm)
4.3 lbs.
2.7 lbs.
10 Tiles (27 sq. ft.)
16 Tiles (43 sq. ft.)
1. PRE-INSTALLATION CHECKLIST
• Consult all associated product
literature concerning adhesive
installation, maintenance and
warranty prior to installation of
flooring.
• Allow all trades to complete work
prior to installation.
• Deliver all materials to the installation
location in its original packaging
with labels intact.
• Do not stack pallets to avoid damage.
• Remove any plastic and strapping
from product after delivery.
• Inspect all material for proper type,
color and matching lot numbers if
appropriate.
• Ensure that all adhesives intended
for installation are approved for use
with flooring material.
• Ensure installation area and material
storage temperatures are between
65° F (19° C) and 85° F (30° C) for
at least 48 hours before, during and
after installation.
• Ensure HVAC system is operational
and fully functioning at normal
operating conditions.
• Protect installation area from
extreme temperature changes, such
as heat and freezing, as well as direct
sunlight for at least 48 hours before,
during and after installation.
• Ensure all substrate preparation
and moisture testing requirements
have been performed, read and/or
understood by all interested parties.
• Do not proceed with installation until
all conditions have been met.
2. PRODUCT LIMITATIONS
Do not install materials over LVT,
cushioned vinyl, hardwood flooring,
cork, rubber, or asphaltic materials.
Do not install flooring materials in
outdoor areas, residences, in or around
commercial kitchens or areas that may
be exposed to animal or vegetable fats
and oils, grease and petroleum-based
hydrocarbons. Do not install in areas
that may be subjected to sharp, pointed
objects, such as stiletto heels, cleats
or spikes. Do not allow product to be
directly exposed to extreme heat sources,
such as radiators, ovens or other high-
heat equipment. May be susceptible
to staining from rubber tires, casters or
rubber-backed walk-off mats, as well
as harsh disinfectants, cleaning agents,
dyes or other harsh chemicals – ensure
all chemicals and materials that may
come in contact with flooring surface will
not stain, mar or otherwise damage the
flooring material prior to use.
3. SUBSTRATE PREPARATION
All substrates must be prepared
according to ASTM F710, as well as
applicable ACI and RFCI guidelines.
Substrates must clean, smooth,
permanently dry, flat, and structurally
Color Group:
Finish:
Nominal Dimensions:
Nominal Thickness:
Weight Per Tile:
Carton Quantity:
Solid, Marble
Diamond
27" x 27" (68.58 cm)
3/16" (4.76 mm)
6 lbs.
6 Tiles (30.375 sq. ft.)
Style #631
Color Group:
Finish:
Nominal Dimensions:
Nominal Thickness:
Weight Per Tile - #671:
Weight Per Tile - #671:
Carton Quantity:
Solid, Marble
Smooth
27" x 27" (68.58 cm)
1/8" (3.175 mm)
8 lbs.
6 lbs.
6 Tiles (30.375 sq. ft.)
Style #671, #871
Landing Tile