Installation & Assembly
TECHNICAL DATA SHEET
01.30.2018 | Page 5
Roppe Corporation | 1602 N. Union St. - Fostoria, OH 44830 | (800) 537 - 9527
RUBBER STAIR TREADS,
RISERS & STRINGERS
raised design
Risers & Stringers
Height:
Thickness:
Toe Length:
Riser Length:
Weight Per Lineal Foot:
Risers Per Carton:
7" (177.8 mm)
.100" (2.5 mm)
9/16" (14.28 mm)
36" (.91 m), 42" (1.07 m),
48" (1.22 m), 54" (1.37 m),
60" (1.52 m) 72" (1.83 m),
84" (2.13 m), 96" (2.44 m),
108" (2.74 m)
0.63 lbs.
20
Risers (RSR)
One-Piece Tread & Riser
Nose Type:
Nose Length:
Leading Edge Thickness:
Back Edge Thickness:
Tread Depth:
Tread Length:
(Optional) Safety Strip Width:
Safety Strip Spacing:
Safety Strip Material:
Coordinating Landing Tile:
Weight Per Lineal Foot:
Treads Per Carton:
Square w/ Taper
1 9/16" (39.69 mm)
13/64" (5.15 mm)
5/64" (2 mm)
20 5/8" (523.87 mm)
36" (.91 m), 42" (1.07 m),
48" (1.22 m), 54" (1.37 m),
60" (1.52 m) 72" (1.83 m)
One 2" (50.8 mm) insert
~3/4" (19 mm) From Nose
Carborundum, Ribbed or Smooth
#995 Hammered Design
2.5 lbs.
6
Nose Type:
Nose Length:
Leading Edge Thickness:
Back Edge Thickness:
Tread Depth:
Tread Length:
(Optional) Safety Strip Width:
Safety Strip Spacing:
Safety Strip Material:
Coordinating Landing Tile:
Weight Per Lineal Foot:
Treads Per Carton:
Square w/ Taper & Relief Cut
1 9/16" (39.69 mm)
1/4" (6.35 mm)
5/64" (2 mm)
20 7/16" (519.12 mm)
36" (.91 m), 42" (1.07 m),
48" (1.22 m), 54" (1.37 m),
60" (1.52 m) 72" (1.83 m),
84" (2.13 m), 96" (2.44 m),
108" (2.74 m)
One 2" (50.8 mm) insert
~3/4" (19 mm) From Nose
Carborundum, Ribbed or Smooth
#996 Vantage Design
2.5 lbs.
6 (4 for all treads over 72")
#95 Hammered Design Tread & Riser #96 Vantage Design Tread & Riser
1. PRE-INSTALLATION CHECKLIST
• Consult all associated product
literature concerning adhesive
installation, maintenance and
warranty prior to installation of
flooring.
• Allow all trades to complete work
prior to installation.
• Deliver all materials to the installation
location in its original packaging
with labels intact.
• Do not stack pallets to avoid damage.
• Remove any plastic and strapping
from product after delivery.
• Inspect all material for proper type,
color and matching lot numbers if
appropriate.
• Ensure that all adhesives intended
for installation are approved for use
with stair tread, riser and/or stringer
material.
• Ensure installation area and material
storage temperatures are between
65° F (19° C) and 85° F (30° C) for
at least 48 hours before, during and
after installation.
• Ensure HVAC system is operational
and fully functioning at normal
operating conditions.
• Protect installation area from
extreme temperature changes, such
as heat and freezing, as well as direct
sunlight for at least 48 hours before,
during and after installation.
• Ensure all substrate preparation
and moisture testing requirements
have been performed, read and/or
understood by all interested parties.
• Do not proceed with installation until
all conditions have been met.
2. PRODUCT LIMITATIONS
Do not install materials over LVT,
cushioned vinyl, hardwood flooring,
cork, rubber, or asphaltic materials.
Do not install stair tread materials in
outdoor areas, residences, in or around
commercial kitchens or areas that may
be exposed to animal or vegetable
fats and oils, grease and petroleum-
based hydrocarbons. Do not install in
areas that may be subjected to sharp,
pointed objects, such as stiletto heels,
cleats or spikes. Do not allow product
Height:
Thickness:
Stringer Length:
Weight Per Stringer:
Stringers Per Carton:
10" (254 mm)
12" (304.8 mm)
0.080" (2mm)
72" (1.83 m)
4.5 lbs. (10")
5.1 lbs. (12")
12
Stringers (STR)