Platform Hoist Owners Manual Color Logo use on white background only Red: 0-100-100-0 Blue: PMS 293 100-56-0-0 Updated: 4-18-17 TP250 250 lb. Capacity Black Logo use on white background only TP400 400 lb. Capacity For the Most Up to Date Information and Instructions, Visit the TranzSporter Web Site at www.tranzsporter.com. White Logo use on black background only Instructions #08238 TIE DOWN ENGINEERING • Atlanta, GA 30336 www.tiedown.
Congratulations on your Purchase of the TranzSporter Lift Hoist. The TranzSporter Lift Hoist was designed to provide safe and continuous operation. Features Include... • • • • • • • • • • • • Collapsible carriage comes with track cam followers for better tracking and handling. Aluminum deck and flap for lighter weight and longer life. Rolled goods/plywood bracket comes with unit and pins into carriage. Motor base is manufactured using laser cut steel tubing for extra strength and durability.
CAUTION: Please read the safety warnings and Instructions contained in this manual before operating the lift hoist. Failure to obey the warnings contained herein could result in damage to the equipment, personal injury, or death, this information should not be a substitute for routine accident prevention, but rather an addition to routine accident prevention. Warning labels are attached to the TP250/400 and are weather resistant.
WARNING: • DO NOT OPERATE THIS EQUIPMENT IF ANY UNSAFE CONDITIONS EXIST OR OCCUR DURING OPERATION. • KEEP TRACK SECTION CLEAR OF ALL ELECTRICAL WIRES AND EQUIPMENT. ALWAYS LOOK UP FOR ELECTRICAL WIRE PRIOR TO MOVING TRACK SECTIONS. • BE AWARE OF OVERHEAD OBJECTS. • NEVER USE TRACK SECTIONS AS A LADDER. • NEVER OPERATE HOIST WITH A HUMAN ON PLATFORM. • NEVER STAND UNDER PLATFORM WHEN LOWERING. • NEVER USE INDOORS OR IN AN AREA WITH POOR VENTILATION (ELECTRIC MODEL IS EXCLUDED).
General Safety Instructions (Continued): 13. Store all parts of the TranzSporter Hoist in such a fashion as not to damage any of the components. 14. Do not operate indoors or in an area with poor ventilation. Electric motor model is excluded. 15. Never lift sheet or panel goods without the use of the plywood brackets and the tie down straps provided (See page 17).
Step 4 “Roll”carriage assembly onto the base. At this time lock the base in place using the Safety Pin as shown. Be sure to loop the lanyard over the carriage base as shown. Important: Always check for wear or damage to the safety pin cable/pull ring assembly. Failure to replace damaged safety pin cable assembly may cause damage or personal injury. Front Front Back Step 5 Back Lay one track section on a flat floor with the “front” side up.
Feed end cable through pully Step 8 Turn the hoist on its side, and working from the back, remove the end of the cable from the drum (shown right). It helps to attach the brake handle, use the brake handle to release the brake drum. The cable will then easily un-spool. Staying on the outside (back) of the base section and track section, take the cable to the top of the last track section where the top cap pulley is attached.
Assembly Instructions for the TP400 Hoist Congratulations on purchasing the TranzSporter TP400 Hoist. Please read the following instructions completely before starting assembly. Step 1 If you have not already assembled the carriage assembly, Stop Now. You must first assemble the carriage, follow the assembly instructions included in the #2 Box “Collapsible Carriage & Plywood Attachments”. Step 2 Remove base section from its box and place on a clean floor or assembly area.
Step 5 “Roll”carriage assembly onto the base. At this time lock the base in place using the Safety Pin as shown. Important: Always check for wear or damage to the safety pin cable/pull ring assembly. Failure to replace damaged safety pin cable assembly may cause damage or personal injury. Front Front Back Back Lay one track section on a flat floor with the “front” side up. This is determined by the space between the track cross bar and the track section edge as shown above.
Step 9 Turn the hoist on one side, from the back side of the hoist, remove the end of the cable from the drum (shown below). It helps to attach the brake handle, use the brake handle back releases the brake drum. The cable will then easily un-spool. Staying on the outside (back) of the base section and track section, pull the cable to top cap on the last track section.
Raising and Lowering the Track Section Assembly WARNING: KEEP TRACK SECTIONS CLEAR OF ALL ELECTRICAL WIRES AND EQUIPMENT. BE AWARE OF OVERHEAD WIRES BEFORE RAISING TRACK SECTIONS. ELECTRICITY KILLS! The hoist assembly is extremely top heavy and must be kept under control at all times. Two alternate methods are suggested for raising the platform hoist to the operating position. Procedure “A” This procedure requires two or preferably three men. 1.
Raising and Lowering the Track Section Assembly WARNING: KEEP TRACK SECTIONS CLEAR OF ALL ELECTRICAL WIRES AND EQUIPMENT. BE AWARE OF OVERHEAD WIRES BEFORE RAISING TRACK SECTIONS. ELECTRICITY KILLS! Procedure “B” This procedure requires two or preferably three men. 1. Place track section assembly perpendicular to the building with the bottom shoes of the steel bottom section resting against the building to prevent slipping. 2.
Hoist Placement and Operational Instructions Track Section Chart: Brace Support and Proper Set Up Distance at Job Site This table provides the suggested information for the distance of the bottom track from the building and the location of the track support for various conditions. Track lengths in excess of 28 feet require the use of the telescoping brace (#60005).
Engine/Motor Base Placement Lift Engine Base Here Engine Base Support Arms Retaining Rings Step 1 Mount the motor assembly to the base unit; from behind the hoist; the foot pad of the motor base slides under the track base section, while “hanging” the motor base. The motor assembly arms must fit outside the two retainer rings shown above. Engine Pully Step 2 Before starting the engine... Align the “V” belt to the large pulley on the base (next to cable drum assembly on track base).
Operating Gasoline Engines IMPORTANT: Lifan and Honda Engines PRIOR TO USE: FILL CRANK CASE WITH OIL. Engine oil recommended: SAE10W-30. As viscosity varies with regions and temperatures, select the proper engine oil in accordance with the chart (on right). IMPORTANT: Gear Reduction Housings Only the Lifan gear reduction housing comes Pre-oiled! The Honda engine gear reduction housing requires Oil! Follow manufactures instructions for adding “Gear Oil” to the Honda gear housing.
Plywood/Flat Panel Tie Down and Lifting Instructions WARNING WARNING WARNING FAILURE TO READ AND UNDERSTAND THE OPERATING INSTRUCTIONS CAN RESULT IN PROPERTY DAMAGE, PERSONAL INJURY OR EVEN DEATH TO USER OR OTHERS • Use the proper tie down equipment - If you are not securing your cargo with the proper safety straps, it could come loose during lifting, resulting in injury or death.
Assembly Instructions TP250/400 Secondary Handle Kit #48468 (Purchased Separately) Allows use of a left side handle to engage the motor and carriage. It is highly recommended when using with the Solar/Plywood Saddle Carriage. Can be used for both TP250 & TP400 models. Parts included with the Secondary Handle Kit: 1 Handle 2 Pivot/Brake Weldmont 3 2 - Mounting Plates 4 4 - Screws 1 2 3 Mounting Slot 4 Step 1 Lay the base section flat on a hard surface.
TRANZSPORTER PRODUCT LINE LIMITED WARRANTY Tie Down Engineering will repair or replace, free of charge, any part, or parts of the TranzSporter lift hoist that are defective in material or workmanship or both. The limited warranty is in effect for 90 days from date of purchase. Return the defective unit to the dealer or contact Tie Down direct at 800-241-1806, x1525.
TP400 Hoist Replacement Parts TP-250 Complete Carriage Wheel Kit Part #90040 Kit Includes: 1/2-13 x 2-3/4” Zinc Bolts (2) 1/2” Lock Washers (2) 1/2” Washers (4) Carriage Wheels (2) TP-400 Complete Carriage Wheel Kit Part #90048 Kit Includes: Carriage Bolts (2) Washers (2) Carriage Wheels (2) Jam Nut (2) Brake Kit Part #90007 Kit Includes: Lock Nut, Eye Bolt, Spring, Cotter Pins, Linkage & Brake Strap TP 250 Complete Drum Assembly Kit Includes: Brake Drums, Cable Drum, Bearings and Cable #48493A Cable Onl
Hoist Accessories H Solar/Plywood Panel Saddle Carriage Allows lifting of four solar panels or plywood sheets. Unique design allows panels to roll off towards the contractor, preventing leaning while on the roof top. Requires roof top anchoring; straps included with carrier. Solar/Plywood Panels attach to TP400 carriage frame. Solar/Plywood Panel Kit #48469 is a complete carriage system for use with the TP250.
