Product Manual B

ManualsBrandsRoofZone ManualsElectric Chain HoistsTranzporter Platform Hoist — 28ft.Lift, 250-Lb. Capacity

TIE DOWN ENGINEERING • Atlanta, GA 30336

www.tiedown.com (404) 344-0000

www.tranzsporter.com

Carriage Assembly Instructions

TP250

(Pages 1-4)

TP400

(Pages 5-8)

Instruction Sheet #08290

E1563; 101317

Congratulations

You’ve purchased a rooﬁng hoist manufactured by TIE DOWN ENGINEERING. All of hoist products are easy to

assembly and is solidly built in USA and tested to ensure years of service.

Before You Begin

We’ve included this easy to use instruction sheet to ensure quick, easy assembly of your carriage

platform. Be sure to read the instructions (a time saver in the long run). Identify all parts and hardware.

Questions?

We’re here to help, just call 800-241-1806. For faster service, have your model and serial number

ready when calling.

Page 1 of 8

Read this manual before using this product.

Failure to follow the instructions and safety precautions in this manual can result in serious

injury or death. Keep this manual in a safe location for future reference.

Summary of content (8 pages)

PAGE 1
www.tranzsporter.com TP250 (Pages 1-4) TP400 (Pages 5-8) Carriage Assembly Instructions Read this manual before using this product. Failure to follow the instructions and safety precautions in this manual can result in serious injury or death. Keep this manual in a safe location for future reference. Congratulations You’ve purchased a roofing hoist manufactured by TIE DOWN ENGINEERING. All of hoist products are easy to assembly and is solidly built in USA and tested to ensure years of service.
PAGE 2
TP250 Carriage Parts Description List Platform Back/Flap Plywood Brackets (TP400 on page 5) Platform Base Description Qty. Platform Back Flap 1 Platform Base 1 Carriage Base 1 Support Struts w/Pins 2 Plywood Brackets w/Pins 2 5/16”-18 x 2” Bolt 4 5/16” Nyloc Nuts 4 Support Struts Carriage Base TP250 Carriage Assembly Instructions (TP400 on page 5) Platform Back/Flap Step #1 Place the Carriage Base (wheels upward) and Platform Base (Smooth flat top upward) on a hard flat surface.
PAGE 3
TP250 Carriage Assembly Instructions Beveled End Step #3 Lift up one side of the carriage 90˚ and let it rest on its side. Support Strut Round End Platform Back/Flap Place the round end of the support strut in the platform (underside) base, align with mounting holes. Beveled End Platform Base The support strut must be positioned with the beveled end as shown right. Insert 5/16”x 2” Bolt through base and strut. Tighten nylock nut with the bolt.
PAGE 4
TP250 Carriage Assembly Instructions Plywood Brackets Step #6 Insert the plywood brackets into slots on the front of the Platform base. If you plan to use the plywood brackets insert the short end into the slots with the long end 90˚ up. Insert safety pins on each bracket. When not in use or during transport turn the plywood brackets down 90˚ and insert safety pins on both sides. Safety Pins When not in use or during transport turn the plywood brackets down 90˚ and insert safety pins on both sides.
PAGE 5
www.tranzsporter.com TP400 Carriage Assembly Instructions Read this manual before using this product. Failure to follow the instructions and safety precautions in this manual can result in serious injury or death. Keep this manual in a safe location for future reference. Congratulations You’ve purchased a roofing hoist manufactured by TIE DOWN ENGINEERING. All of hoist products are easy to assembly and is solidly built in USA and tested to ensure years of service.
PAGE 6
TP400 Carriage Parts Description List Platform Back/Flap Description Qty. Platform Back Flap 1 Platform Base 1 Carriage Base 1 Support Struts w/Pins 2 Plywood Brackets w/Pins 2 5/16”-18 x 2” Bolt 2 5/16”-18 x 1” Bolt 2 5/16” Nyloc Nuts 4 Platform Base Carriage Base Support Strut TP400 Carriage Assembly Instructions Pivot Tab Holes Platform Base Lift This Side Step #1 Place the Carriage Base (wheels down) and Platform Base (Smooth flat top down) on a hard flat surface.
PAGE 7
TP400 Carriage Assembly Instructions Carriage Base Step #3 Flip the carriage base over so that it lays flat on top of the carriage base Align the platform back/flap tap holes with the carriage holes. Insert 5/16”x 1” bolt through back/flap tap holes and carriage base, Tighten nylock nut with the bolt. Do not over-tighten nyloc nut so tight as to prevent free movement. Platform Back Flap Platform Base Platform Back/Flap Tab Holes Repeat for the other side.
PAGE 8
TP400 Carriage Assembly Instructions Plywood Brackets Safety Pins Plywood brackets used when handling panel goods. Plywood brackets in position for transport or storage. Step #5 Flip the completed base over. Insert the plywood brackets into slots on the front of the Platform base. If you plan to use the plywood brackets insert the short end into the slots with the long end 90˚ up. Insert safety pins on each bracket.